Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 11 of 11 for “"Glaze layer"”.
-
Wear Rate and Mechanism Maps for Stainless Steel at High Temperature
… that a compacted and sintered wear protective layer, namely “glaze layer” can be formed in many Co, Ni and Fe alloys under certain circumstances, and it is possible to take advantage of glaze layer formation to reduce friction and wear at high temperature. The dissertation is aimed for better …
-
Wear and Erosion Behaviours of FeCoCrNi-based Medium- and High-Entropy Alloys
… and Cr. FeCoNi rapidly developed a Co3O4-based glaze layer that improved wear resistance at moderate temperatures but failed at 1000 °C due to layer deformation. The development of a Cr2O3-rich glaze layer was delayed in CoCrNi, but the layer remained resistant to wear at 1000 °C. Alloying both …
-
An Investigation of Molybdenum Disulphide Dry Film Lubricant Coatings used in Aero-Engine Fan Disc Applications
… retained in the contact, a durable, low friction glaze layer was observed to form on the surface. This layer occurred as a consequence of compaction and sintering of wear debris, generated during the initial interaction between the two surfaces. With time, this layer was observed to lose …
-
Development and Tribological Performance of Thermally Sprayed Coatings Inspired by Glaze Layers
Ceramic coatings inspired by the glaze layers naturally formed on Co-Cr-W superalloys (e.g., Haynes 25) were developed to meet the demands of next-generation gas turbine engines operating at elevated temperatures. Four distinct chemical compositions were investigated: CoO, CoO-21Cr₂O₃, CoO-42Cr₂O₃, …
-
Effect of surface finish on wear of ceramics
… treatment (polished, machined, polished, then glazed, and machined, then glazed). Ceramics were subjected to 200,000 cycles against Vita Mark II using the two-body pin-on-plate linear wear tester under dead weight a load of 1 Newton. The wear performance of ceramic was determined using volume …
-
Toothbrush Resistance Of Resin-Based Stain And Glaze Materials Applied To 3D-Printed Denture Resins
… resin, after which surface stain and glaze coatings are applied to reproduce gingival coloration, enhance the esthetic appearance and improve clinical longevity of characterized prostheses. However, daily oral hygiene procedures such as toothbrushing degrade surface coatings, leading …
-
Efeito de diferentes regimes de acabamento e polimento na resistência à flexão e topografia superficial de zircônias monolíticas
… + diamond polishers, PG- grinding with burs + glaze) and "Degradation" - 2 levels (WithD: autoclave at 127 ° C, 1,7 bar / 24h, without degradation). The miniflexion resistance test (3 points) was performed, with v: 1mm / min and 500N and 5000N load cells. Two samples from each group were …
-
Μελέτη της βυζαντινής κυπριακής εφυαλωμένης κεραμικής: διερεύνηση της τεχνολογίας κατασκευής και της προέλευσης με φυσικοχημικές μεθόδους
… present PhD thesis, samples of Cypriot Byzantine glazed ceramics and tripod stilts were studied by means of micro X-Ray Fluorescence Spectrometry (μ-XRF), Powder X-Ray Diffraction (PXRD), Scanning Electron Microscopy with Energy Dispersion Spectrometry (SEM - EDS) and Atomic Emission Spectroscopy …
-
The effect of full-contour Y-TZP ceramic surface roughness on the wear of bovine enamel and synthetic hydroxyapatite : an in-vitro study
… procedure: G1-as-machined (n = 8), G2- glazed (n = 16), G3-diamond bur-finishing (Brasseler, USA) (n = 8) and G4- G3+OptraFine polishing kit (Ivoclar-Vivadent) (n = 16). Thirty-two sintered HA disks (diameter = 11 mm × 2.9 mm in height) and 16 bovine enamel samples with a minimum surface …
-
Investigation of Glaze Formation in Reciprocating Wear of Superalloys
… avoid metal-to-metal contact is to have an oxide layer on the surface. As sliding begins, the transient oxide layers on the surface break down due to adhesive wear. This exposes fresh metal, which then oxidises, generating wear debris in the contact area and resulting in abrasive wear. These …
-
Brake performance and emission behaviors of brake materials on a sub-scale dynamometer
… processes are high enough to form a thick glaze layer on the surfaces. The glaze layers were correlated to a lubricating effect, or fade effect, at disc temperatures above 400 °C, especially when their extension covered the steel fibers. The cermet-coated disc displayed the same fade …