Global ETD Search

Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.

Results

Showing 1 to 20 of 102 for “"HEAT TRANSFER MODELS"”.

  1. Thermodynamic and heat transfer models of an open accumulator.

    … air but creating large temperature swings if the heat transfer during compression and expansion is poor. This thesis investigates thermodynamic and heat transfer aspects of an open accumulator to assist in its design. A thermodynamic model was created to determine the efficiency and required heat …

    umn Repository record for Thermodynamic and heat transfer models of an open accumulator. (opens in a new tab)

  2. Comparison of heat transfer models at the pebble, gas and reflector interface in the PBMR

    … of the PBMR to accurately predict gas flow and heat transfer in the reactor. Understanding the heat transfer at the core-reflector interface in particular is a very important aspect as the reactivity of the control rods housed in the reflectors is highly temperature dependent. It is also very …

    nwu-za Repository record for Comparison of heat transfer models at the pebble, gas and reflector interface in the PBMR (opens in a new tab)

  3. Climate resilience: Examination of revised heat transfer models in the enhanced integrated climatic model for pavement temperature prediction

    … predictions from externally based climate models into the MEPDG to create robust designs for climate change. As pavement designers and researchers seek robust solutions while formulating resilient pavement designs, it is likely that the EICM will be used to import predicted pavement …

    marshall Repository record for Climate resilience: Examination of revised heat transfer models in the enhanced integrated climatic model for pavement temperature prediction (opens in a new tab)

  4. A study of the heat transfer in low temperature combustion engines

    … work, an experimental study was performed of the heat transfer in low temperature combustion engines. The heat transfer was measured in two single-cylinder engines: a Waukesha CFR engine at Ghent University and a Scania D13 engine at Lund University. The CFR engine was operated in HCCI mode and …

    ghent Repository record for A study of the heat transfer in low temperature combustion engines (opens in a new tab)

  5. Granular Flow Experiments and Models Coupled with Measured Temperature-Dependent Properties for Solar Thermal Energy Transport and Storage

    … electricity, renewable fuel, and production of heat for industrial processes. High temperature granular media were characterized for solar thermal energy transport and storage. The characterization included three steps: (1) measurement of flow properties of granular media at different …

    gatech Repository record for Granular Flow Experiments and Models Coupled with Measured Temperature-Dependent Properties for Solar Thermal Energy Transport and Storage (opens in a new tab)

  6. Predicting temperature profiles during simulated forest fires

    … when conducting prescribed fire programs. Heat transfer models in soil are needed to predict temperatures in soil during forest fires. Many of the heat transfer models in soil that include the effects of moisture are complex and in most cases do not have very good predictive abilities. …

    sask Repository record for Predicting temperature profiles during simulated forest fires (opens in a new tab)

  7. CFD Modelling of Generic Gas Turbine Combustor

    … as turbulent swirling flow, chemical reactions, heat transfer, and so on. In this project we try to design a simple yet accurate model, for a generic combustor of industrial interest, that may be tested in a relatively short time and that yields reliable results. An important topic is here to …

    chalmers Repository record for CFD Modelling of Generic Gas Turbine Combustor (opens in a new tab)

  8. A Comprehensive Heat Transfer Analysis for Thermoplastic Composites Made by Automated Fiber Placement Using Hot Gas Torch

    … gradients and residual stresses, accurate heat transfer models need to be developed. In this study a two-dimensional transient heat transfer model was developed for thermoplastic structures manufactured by AFP process with a hot gas torch. The accuracy of heat transfer model for AFP process …

    concordia Download PDF for A Comprehensive Heat Transfer Analysis for Thermoplastic Composites Made by Automated Fiber Placement Using Hot Gas Torch (opens in a new tab)

  9. A coupled electromagnetic and heat transfer finite-element model for simulating microwave processing of composite materials in a cylindrical resonant cavity

    A coupled electromagnetic/heat transfer model capable of simulating microwave processing of composite materials in a cylindrical resonant cavity was developed. The two-dimensional model simulates processing of axisymmetric material loads in cylindrical resonant cavities operating in the TM₀₁₀ mode. …

    vt Repository record for A coupled electromagnetic and heat transfer finite-element model for simulating microwave processing of composite materials in a cylindrical resonant cavity (opens in a new tab)

  10. Using STAR-CCM+ to Evaluate Multi-User Collaboration in CFD

    … architecture is tested and evaluated on five models. The testing of these models is a start to finish set-up of an entire simulation excluding computational time for generating mesh and solving the solution. The different models have distinct differences which test every operation that would …

    byu Repository record for Using STAR-CCM+ to Evaluate Multi-User Collaboration in CFD (opens in a new tab) Download PDF for Using STAR-CCM+ to Evaluate Multi-User Collaboration in CFD (opens in a new tab)

  11. Thermodynamic Analysis of an Autogenous Pressurization System

    … of pressure-fed systems, the plethora of heat and mass transfer mechanisms mentioned earlier complicate the modeling process. Therefore, the research presented in this thesis does not attempt to define a single, generalized model of autogenous pressurization. Instead, this research aims to …

    ut-knoxville Repository record for Thermodynamic Analysis of an Autogenous Pressurization System (opens in a new tab)

  12. Microwave heating of a coating on a temperature-sensitive substrate

    Microwave heating has been considered for the heating of a coating in contact with a temperature-sensitive substrate. A methodology was developed to conduct a microwave heating feasibility study for a candidate system. The study consisted of dielectric property determination, development of heat …

    vt Repository record for Microwave heating of a coating on a temperature-sensitive substrate (opens in a new tab)

  13. Numerical Modelling for Alternative Solution Designs of Steel and Timber Structures in Fire

    … in fire was gained and the knowledge was transferred to numerical model development. A validated modelling methodology allows designers to predict structural performance in fire which can then be used to justify decision making and as a method to show the design is code compliant. This …

    york Repository record for Numerical Modelling for Alternative Solution Designs of Steel and Timber Structures in Fire (opens in a new tab)

  14. Design, Modeling, and Thermal Characterization of Temperature Gradient Gas Chromatography Micro-Columns

    … out of silicon with 21 nickel thin-film heaters evenly placed along the length of the column. Computational heat transfer models using ANSYS Mechanical APDL predict heating and cooling rates up to 32,000 deg C/min and 3,600 deg C/min, respectively. These results are verified through …

    byu Repository record for Design, Modeling, and Thermal Characterization of Temperature Gradient Gas Chromatography Micro-Columns (opens in a new tab) Download PDF for Design, Modeling, and Thermal Characterization of Temperature Gradient Gas Chromatography Micro-Columns (opens in a new tab)

  15. Theoretical study of the improvement of the condensation rate of a vertical condensing plate in a basin type desalination unit

    … was calculated using empirical and theoretical heat transfer models, under both drop and filmwise condensation conditions to determine their effects on the amount of useable water produced by the system. The filmwise and dropwise models were verified through a results comparison with known …

    ttu Repository record for Theoretical study of the improvement of the condensation rate of a vertical condensing plate in a basin type desalination unit (opens in a new tab)

  16. Study of Granular Flow and Radiative Properties of Bauxite Particles for Solar Thermal Applications

    … particles are important for understanding energy transfer processes in solar energy conversion by particulate media. Single particle scattering properties were measured by the unique taped particle method with a laser scatterometer. Modeling granular flow is necessary for delivering mass transport …

    gatech Repository record for Study of Granular Flow and Radiative Properties of Bauxite Particles for Solar Thermal Applications (opens in a new tab)

  17. Heat transfer, pressure drop and void fraction in two-phase, two-component flow in a vertical tube

    … existing in two-phase, two-component flow where heat transfer, pressure drop and void fraction have all been measured under the same conditions. Such data are very valuable for two-phase heat-transfer model development and for testing existing heat-transfer models or correlations requiring …

    manitoba Repository record for Heat transfer, pressure drop and void fraction in two-phase, two-component flow in a vertical tube (opens in a new tab)

  18. Solidification and heat transfer in the continuous casting of steel

    … gold. One and two-dimensional finite difference heat transfer models were developed to calculate the pool profiles in strands being continuously cast. The predicted pool profiles and pool depths have been compared to profiles measured from autoradiographs and pool depths measured with tungsten …

    ubc Repository record for Solidification and heat transfer in the continuous casting of steel (opens in a new tab) Download PDF for Solidification and heat transfer in the continuous casting of steel (opens in a new tab)

Page 1 of 6