Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 16 of 16 for “"High-speed testing"”.
-
High-speed, low cost test platform using FPGA technology
… research is to develop a low-cost, adaptable testing platform for multi-GHz digital applications, with concentration on the test requirement of advanced devices. Since most advanced ATEs are very expensive, this equipment is not always available for testing cost-sensitive devices. The approach …
-
Experimental Emissions and Fuel Economy Analysis of a Diesel Engine Operating on Vegetable Oil
… six steady state test modes of different engine speeds and loads. It was determined that the engine exhaust emissions was similar for both VO and diesel fuel. However, the soot production for VO was higher under maximum load and high speed testing conditions. This study suggests that VO is an …
-
Empirical Modeling of Tilt-Rotor Aerodynamic Performance
… of the NASA LA-8 aircraft. Investigation of low-speed performance included a maximum speed of 12 m/s and a maximum RPM of 6800 tested over a range of incidence angles from 0° to 100°. High-speed testing achieved a maximum speed of 30 m/s and maximum RPM of 6000 while incidence angle was varied …
-
Intermediate strain rate testing methodologies and full-field optical strain measurement techniques for composite materials characterisation
… is relatively unexplored. For this purpose a testing methodology that combines high speed imaging and the use of a high speed test machine is devised. The overall goal is to extract composite materials constitutive parameters to be used in the modelling of strain rate dependent behaviour. …
-
Low-Speed Flight Testing and System Identification of a Small-Scale Supersonic Uncrewed Aerial Vehicle
… demonstrator possessing satisfactory low-speed stability and control characteristics. Following an iterative prototype development program, sustained flight of a second-generation demonstrator was achieved. Comprehensive development consisted of: modular design and fabrication; ongoing …
-
Algorithms and methodology for incoherent undersampling based acquisition of high speed signal waveforms using low cost test instrumentation
… wide-band waveform acquisition techniques for testing high speed com- munication systems. High resolution waveform capture is a versatile testing tool that enables flexible test strategies. However, waveform capture at high data rates requires costly hardware because the increased bandwidth of …
-
Modelling and Nonlinear Control of Instability in Electric Skateboards
… electric drive system has greatly increased the speed achievable on the skateboard platform, driving the need for investigation into the dynamic instabilities associated with this unique mode of transportation. At high speeds, the skateboard system encounters a bifurcation, at which point the …
-
High-speed lateral stability analysis of articulated heavy vehicles using driver-in-the-loop real time simulation
High-speed testing procedures for evaluating the lateral stability of multi-trailer articulated heavy vehicles (MTAHV) include the use of both an open-loop and a closed-loop maneuvers as specified in ISO-14791. The standard testing procedures are used to determine the Rearward Amplification (RA), …
-
Mixed-Signal Implementation of Low-Density Parity-Check Decoder
… good BER is a metric of reliable communication, high throughput and energy-efficiency are also desired. Low-density parity-check (LDPC) decoders are able to perform well in term of these metrics. In this thesis, the Modified Differential Decoding Binary Message Passing (MDD-BMP) algorithm of LDPC …
-
An integrated low-cost functional tester for CMOS logic
… Very Large Scale Integration (VLSI) chips. The testing of timing parameters become increasingly important with higher performance technology. Circuits that operate correctly at low speeds may fail at higher speeds because of timing problems. Most low-end test systems lack the performance …
-
An Experimental Investigation Of The Aerodynamic Losses For An Incident Tolerant Low Pressure Turbine Blade Over Moderate To Low Reynolds Numbers At Engine Representative Mach Numbers
… as the engine transitions from 100% shaft speed at takeoff to 54% shaft speed at cruise. The blading in this engine must be designed to optimize fuel efficiency, especially at cruise. The flow conditions in the LP turbine will change significantly from a Reynolds number of about 500,000 …
-
Study of A Direct Measuring Skin Friction Gage with Rubber Compounds for Damping
… surface, and for temperature compensation. In high speed testing the oil leaks out; therefore, a gage with rubber to fill the gap instead of oil was introduced This study employed a finite element method model to fully understand the strains involved with the rubber and the skin friction gage. …
-
Investigation of wear mechanisms in abradable-blade contacts
… blades and NiCrAl-bentonite abradable used in higher temperature compressor stages. This was accomplished through commissioning a new high-speed testing rig with a capability to achieve speed up to 280m/s and instrumenting it with a front-on stroboscopic imaging system. The new imaging system …
-
Analysis of rate-dependent deformation and fracture phenomena during cutting of viscoelastic materials
… regarding a process description for industrial high-speed cutting. The aim of the work is the analysis of the velocity-dependent cutting behavior of foods up to the high-speed range. The focus is on the deformation and fracture phenomena, analysed by methods of classical material analysis but …
-
The Dynamic Character of the Flow Over a 3.5 Caliber Tangent-Ogive Cylinder in Steady and Maneuvering States at High Incidence
… over a 3.5 caliber tangent-ogive cylinder at high angles of incidence. The goal of the investigations is to characterize the natural and forced flow unsteadiness, using a variety of experimental tools. In the first investigation, flow data are collected over a stationary model in a water …
-
Towards certification by analysis of thermoplastic composites for aircraft structures: an integrated experimental and computational approach
In the present thesis, several novel integrated testing and numerical methodologies are devel-oped towards the certification of new thermoplastic composite systems used in primary aero-space structural applications, through the building block approach, reinforcing the need of research community and …