Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 57 for “"Hot embossing"”.
-
Hot embossing of polymeric tubular micro-components
… have led to the development of a hot embossing process and corresponding machine for shaping polymeric micro-tubes. The targeted tubular micro-components are of an initial outer diameter of 1.6mm or below, and have reduced inner feature in the micron meter ranges. The proposed …
-
ABAQUS simulation and optimization of PMMA hot embossing process
… the industry has led to increasing attention to hot embossing technology. The hot embossing technology has developed a lot for the past few decades and been proved to be capable to replicate microstructure with high efficiency and high accuracy. This thesis is going to establish a numerical hot …
-
Study of Polymer Flow Behavior in Cavity Filling of Alignment Structures in Micro Hot Embossing
… of polymer flow is a critical aspect in micro hot embossing. The flow behavior significantly depends on the process parameters including molding temperatures and displacement of a mold with respect to a polymer substrate. To achieve accurate replication of microstructures, it is necessary to …
-
Design of a Mold Insert Alignment System for Double-Sided Hot Embossing of Microfluidic Devices Using Kinematic Constraints
The fabrication of microfluidic devices using hot embossing has increased in complexity. Many systems are multi component systems requiring that each be aligned properly with its mating components. Double-sided hot embossing is often used to produce stackable components for these assemblies. …
-
Fabrication of Through-Holes for the Interconnection of Polymer Microfluidic Devices
… into cost effective polymer devices. Hot embossing has been proposed in the fabrication of through-holes. This would allow a fluidic sample to be transferred between multiple interconnected Point-of-Care diagnostics (POCD) systems. The hot embossing process was modified to increase the …
-
Alternative replica molding methods for polymer based microfluidic channels
… can be expensive to prototype due to the use of photolithography equipment meant for the semiconductor industry. In addition, the majority of microfluidic research has been done using rectangular channels but in some cases the ability to make circular cross-section channel microfluidic devices …
-
Rapid production of polymer microstructures
… research is to develop an integrated polymer embossing module, with which difficult-to-emboss polymer microstructures and microparts can be fabricated in a cost-effective manner. In particular, the research addresses three major limitations of the hot embossing process, namely, long cycle …
-
Design of Uniformly Textured Polymer Surfaces for Hard-soft Bearing Systems
… textured surfaces is described that uses hot embossing. The protocol was optimized to produce textured test samples that achieve 95.6% of their target dimensions. Pilot studies of pressure distribution under quasi-static load using a flat cylindrical punch show trends consistent with model …
-
A Template-based Approach for Mass Fabrication of Dielectric Resonator Antenna & Arrays
… nickel molds, which are subsequently used in hot embossing of acrylic sheets for potentially low cost replication of DRA arrays. A detailed investigation into the impact of template material on embedded DRA performance is carried out through simulations and also scrutinized analytically. …
-
A Template-based Approach for Mass Fabrication of Dielectric Resonator Antenna & Arrays
… nickel molds, which are subsequently used in hot embossing of acrylic sheets for potentially low cost replication of DRA arrays. A detailed investigation into the impact of template material on embedded DRA performance is carried out through simulations and also scrutinized analytically. …
-
Fabrication of Long Range Surface Plasmon Polariton Biosensors incorporating Optical Waveguides and Encapsulated Microfluidic Channels via Wafer Bonding"
… attenuation loss of 4.92 dB/mm. An alternative hot embossing process for formation of microfluidic channels on a TOPAS substrate was investigated.
-
Fabrication of proton beam micromachined scaffolds for cell behaviour studies
… surface. Studies are underway to implement the hot embossing process which will allow faster replication of 3D structure to help the analysis of the genes involved in the endothelial cell responses associated with geometrical constraints.
-
The replication of micron scale pillar arrays for medical ultrasound applications
… remain laboratory based. Viscous polymer (VP) embossing has been demonstrated as a route to smaller feature sizes and higher aspect ratios, but the process is limited by the availability of suitable moulds, which must be replicated to make the process cost effective. This thesis reviews the …
-
Fabricating microfluidic devices in polymers for bioanalytica applications
… sacrificial mask, polyimide membrane mask and embossing techniques. PMMA microfluidic devices fabricated using X-ray lithography were characterized using scanning electron microscopy (SEM) and optical microscopy, while analytical techniques such as electroosmotic flow determination, …
-
Investigations of the Fresnel Lens Based Solar Concentrator System through a Unique Statistical-Algorithmic Approach
… this concentrator with high-efficiency photon and heat outputs and a minimized effect of chromatic aberrations. First, a MATLAB®-incorporated algorithm optimizes both the flat-spot and the curved lens designs via a statistical ray-tracing methodology of the incident light, considering all …
-
A Study of Micro-Mechanical Punching for the Interconnection of Polymer Microfluidic Devices
… process was integrated with double-sided hot embossing. A pair of mold inserts were designed with features for the fabrication of through-hole, and features for a passive alignment step. Features for mechanical punching were designed to provide five levels of punch to die clearances, and a …
-
Microbead-Based Biosensing in Microfluidic Devices
… microbead-based biosensing devices. A customized hot embossing technique was used to stamp an array of microwells in a thin plastic substrate where appropriately functionalized agarose microbeads were selectively placed within a conduit. Functionalized quantum dot nanoparticles were pumped through …
-
Interfacing Microfluidic Bioanalysis with High Sensitivity Mass Spectrometry
… polymer microfabrication techniques such as hot embossing and polymer bonding were discussed. Among those, a novel bonding technique of using UV/Ozone surface treatments for achieving low temperature bonds between poly(methyl methacrylte) (PMMA) and cyclic olefin copolymer (COC) microfluidic …
-
Microfluidic devices for biomolecular and cellular analysis
… with LIF detection. Another CE chip was made by hot embossing PMMA (polymethyl methacrylate). It was used to an antibiotic resistance measurement with mecA gene. Confocal four-colour laser induced fluorescence detection system was developed for roll-to-roll hot embossed PMMA chip. Glass chip was …
Page 1 of 3