Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 110 for “"IIP3"”.
-
Understanding distortion in silicon-germanium transistors, and its application to RF circuits
… is the Input/Output Third Order Intercept Point (IIP3/OIP3), which represents the input/output power level at which the power of fundamental frequency (PFUND) become equal to that of the third-order intermodulation product (P3rd). Clearly, a higher IIP3 number yields improved linearity, and is …
-
Reconfigurable Mixer Design for Software-Defined Radios
… (IRR), acceptable third-order intercept point (IIP3), and good conversion gain (CG) while maintaining a low noise figure (NF). However, the existing architectures cannot maintain good trade-offs among these performance parameters and doesn’t have wide tuning range. Despite the rapid development …
-
Structured design of a 60 GHz LNA in 40-nm CMOS technology
… taking also other specifications such as IIP3 into account. The results of each level of design are given and analyzed. The final simulation results show that the LNA achieves 4.5 dB noise figure, 11 dB available gain, 16 dB voltage gain and 0 dBm IIP3 with 12 mW power consumption.
-
Design of mm-wave Front-end for Multiantenna Communication Systems
… tor diodes is demonstrated and it achieves an IIP3 of 45 dBm, with a conversion loss of 20 dB. In order to support the proposed mixer, an inductive emitter-degenerated cascode LNA cascaded with a differential pair active balun is proposed. The LNA has a reflection coefficient of less than -20 …
-
Millimeter-Wave Wideband Mach-Zehnder Modulator Driver Design in CMOS Technology
… enhances the third-order input intercept point (IIP3) to 4.8 dBm at 25 GHz. The second work introduces a co-integrated 16-32GHz RF photonic front-end with a 22nm CMOS driver and a silicon traveling-wave MZM (TW-MZM) for radio-over-fiber systems. It integrates an MCR-based impedance matching …
-
Modelling of Spectral Regrowth
… scale, ACPR was confirmed to depend on IIP3 with a factor of 2 dB/dBm while the dependence on input power is a factor of -2 dB/dBm. The model can predict the ACPR for different channel setups with a maximum deviation of 2.3 dB compared to measurements, for the majority of the frequency …
-
Design of CMOS active downconversion mixers for gigahertz multi-band and multiple-standard operation
… an IBM 0.13 mm CMOS process improvements on IIP3 and IIP2 in comparison to the conventional Gilbert-cell mixer are demonstrated. For the first topology, we achieved a conversion gain of 10.2 dB with a NF of 12 dB for the designed mixer working at 2 GHz, with a low-IF of 500 kHz and an IIP2 …
-
Broadband microwave diode mixer design and implementation
… most frequencies across the band. Furthermore, IIP3 of 13 dBm is achieved for LO drive level of 13 dBm. The second design proposes improved IF bandwidth up to 4 GHz. Conversion loss of 6 dB is typically measured for the RF frequency of 5 GHz-15 GHz. It shows excellent LO-RF isolation of better …
-
Highly linear low noise amplifier
… Linearity is usually measured in terms of IIP3 and the LNA has an IIP3 of +21dBm, with a gain of 11 dB, NF of 3.1 dB and power consumption of 22.5 mW.
-
Wideband Inductor-less LNA with Resistive Feedback and Noise Cancelation
… gain of 27 dB. The NF is below 2.1 dB and IIP3 is greater than -4 dBm with a power consumption of only 28 mW. In the receiver test bench the mixer is used as load which results in a conversion gain higher than 24 dB, S11 below -12.8 dBm, NF below 4 dB and IIP3 higher than -6.2 dB. This …
-
Inductorless balun low-noise amplifier (LNA) for RF wideband application to IEEE 802.22
… figure), an input third-order intercept point (IIP3) > 3.3 dBm (7.6 dBm max.) and an input power reflection coefficient S11 < -16 dB. When optimized for best NF, it achieves a voltage gain > 24.7 dB (power gain > 19.8 dB), a NF < 2 dB over the entire band, an IIP3 > -0.3 dBm and an S11 < -11 dB. …
-
Linearized 4-7 GHz LC Tunable Filter with Active Balun in 0.18um SiGe BiCMOS
… input while preserving noise figure and IIP3 performance. Two different linearization techniques are applied for the balun designs. Simulated NF ranges from 7.5 to 13 dB and IIP3 averages about 5 dBm with the peak value of 21 dBm.
-
Study of Radio Base Station Receiver Topologies for Multiband use
… in the laboratory the Noise Figure, Gain, IIP3 of each branch were measured. 3GPP co-location specification was measured too, for each branch, and inter branch. The results obtained in the laboratory, Noise Figure and IIP3 are 3GPP compliant. Good margins exist in all cases, 1 and more than …
-
High Linearity Full Duplex System Implemented with Novel Impedance Matching Network
… a highly-linear impedance matching network, the IIP3 can reach +60dBm with a VSWR of 1.5:1. Additionally, the overall cancellation depth from TX to RX is larger than 60dB.
-
CMOS integrated commutated circuits for interference filtering at radio-frequency
… operates at 3.5-to-6.2 GHz and achieves IIP3 of >+27 dBm at 1xBW offset with a minimum NF of 9.7 dB in measurement. For the N-path LPF, a mathematical analysis on N-path LPF is given, and a good match between theoretical plots and Cadence simulation is reported.
-
Nonlinear characterisation of reconfigurable antennas
… asymmetry, third-order input intercept point (IIP3) and 1-dB gain compression point (P\(_1\)\(_-\)\(_d\)\(_B\)). The measurements are performed when the antenna is transmitting signals. All measurements are performed on the state-of-the-art, 4-port ZVA67 Rohde & Schwarz VNA. Based on the …
-
Design of a 3.1-4.8 GHZ RF front-end for an ultra wideband receiver
… of 15dB, noise figure of less than 2.6dB and IIP3 of more than -7dBm. Mixer is a modified version of double balanced Gilbert cell topology where both I and Q channel mixers are merged together. Frequency response of each sub-band is matched by using an additional inductor, which further …
-
Reconfigurable Circuits for Communication Applications and Environment-Aware Receivers
… required phase noise and main linearity merits, IIP3 and P1dB. A novel highly linear, recon figurable mixer with four states of power consumption and linearity is designed based on the dynamic current injection method, introduced in this work. The mixer is a crucial part of the proper adjustment …
-
High-Isolation Low-Power Active Quasi-Circulator for 44GHz Transceiver with Power and Noise Optimization in 0.18 Micrometer BICMOS
… combiner. OIP3 of in-phase divider is 8.15dBm, IIP3 is 4.48dBm, P1dB,in is -5.97dBm. OIP3 of out-of-phase active combiner is 5.18 dBm, IIP3 is 3.85dBm, P1dB, in is -2.79dBm. All the isolations better than -37 dB are achieved and forward gains better than 4 dB are achieved with power consumption …
-
Design of Ultra Wideband RF IC for Medical Imaging Applications
… good performance compared with other works with IIP3 of -0.996 dBm. Finally, all of these specifications are achieved while consuming only 4.01 mW and occupying 1.3 mm2 of chip area.</p> <p> Second, an ultra-wideband mixer is designed to work as a multiplier in this configuration, and to perform …
Page 1 of 6