Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 34 for “"In-plane bending"”.
-
Static strength of fabricated trunnion and x-joint under shear and in-plane bending moment
Current trunnion joint design practice is very conservative. The detailed engineering designs for trunnion are empirical and dependent on the ingenuity of experienced engineers using empirical equations for design checks. The objective of this study is to close this gap and provide a more rational …
-
Behavior of Sandwich Panels Subjected to Bending Fatigue, Axial Compression Loading and In-Plane Bending
This thesis investigates experimentally and analytically the structural performance of sandwich panels composed of glass fibre reinforced polymer (GFRP) skins and a soft polyurethane foam core, with or without thin GFRP ribs connecting skins. The study includes three main components: (a) …
-
The influence of end constraints on pipe bends : a study of smooth pipe bends with flange and tangent pipe end constraints under in-plane bending
The importance of smooth pipe bends in design of piping systems is well established. Recent publications have been increasingly concerned with the effect of end constraints on the behaviour of smooth bends but there have been relatively few attempts at a solution to the problem. The divergence …
-
Design Methodology for Composite Structures Consisting of Reinforced Hollow Brick Walls and Concrete Beams Connected at a Joint With Flashing and Subject to In-Plane Bending
<p>Due to waterproofing requirements, a flashing joint is generally used at the base of a brick wall to facilitate transport of moisture from the back of a brick wall to the outside of the building. The flashing results in a loss of bond and reduced friction between the reinforced brick wall and …
-
Design of Fillet and PJP Welds in CHS-to-CHS Moment T-Connections: Finite Element Investigation
… the effective geometric property approach in AISC 360-22 for design of welds in circular hollow section (CHS)-to-CHS moment T-connections under in-plane bending. Experimental data from previous full-sized connection tests is used to verify a finite element (FE) modelling approach for …
-
Fracture and Failure Assessment of Fatigue-Cracked Circular Hollow Section X-Joints
In the present study, five fatigue cracked large-scale circular hollow section X-joints with different surface crack profiles at the weld toe were tested under in-plane bending. The present study discovered the first incidence of brittle lamellar splitting phenomenon in laboratory for large-scale …
-
Experimental characterisation and forming analysis of pure unidirectional stitched glass fibre non-crimp fabric
… on the experimental characterisation and forming analysis of pureunidirectional non-crimp fabric (pure-UDNCF). This fabric consists of low-stiffness polyamide stitches with a tricot-chain stitching pattern where the chain stitches run along the front of the fabric, perpendicular to the glass …
-
Experimental study of inelastic stress concentration around a circular notch
Experiments were conducted to determine whether energy-density relations can be used to predict elastic-plastic stresses and strains near a circular notch for 7075-T6 aluminum alloys and ARALL 4 composites. The loading conditions were tension and four-point bending. Glinka and Neuber have developed …
-
Performance quantification of tidal turbines subjected to dynamic loading
The behaviour of Tidal Stream Turbines (TST) in the dynamic flow field caused by waves and rotor misalignment to the incoming flow (yaw) is currently poorly understood. The dynamic loading applied to the turbine could drive the structural design of the power capture and support subsystems, device …
-
Plasticity-Induced Fatigue Crack Closure For Structural Steels In Offshore Applications.
This thesis investigates experimentally and numerically the plasticity-induced fatigue crack closure (PIFCC) behavior in S355 offshore structural steels through large-scale in-plane bending fatigue tests of circular hollow section (CHS) X-joints and small-scale fatigue tests of C(T) and M(T) …
-
EXTENSION OF η METHOD TO MEASURE CRACK DRIVING FORCE OF SURFACE-CRACKED CIRCULAR HOLLOW SECTION X-JOINT
… positions of a Circular Hollow Section (CHS) X-joint can severely reduce the strength. Hence, it is crucial to have accurate estimations of the elastic-plastic crack driving force of the surface cracks. In this work, the η method is extended to surface-cracked CHS X-joints under brace in-plane …
-
GEOMETRICALLY NONLINEAR FINITE-ELEMENT ANALYSIS OF CIRCULAR AND ARBITRARY ARCHES
A curved nonlinear finite element is developed in this work to observe the behavior of slender arches which undergo large deformations. The derivation of the strain equation is based upon the assumption that cross sections of the undeformed state remain undeformed and plane, but not necessarily …
-
Analytical Evaluations of Buckling Behavior of Wood Composite I-Joist with Sinusoidal Web
Flexural-torsional buckling or lateral torsional buckling is an important limit state for wood composite I-joist because the in-plane bending stiffness is typically greater than torsional lateral bending stiffness. Web local buckling is another important limit state because of the thin-walled web …
-
Characterizing the Vibrational Spectra of Hydrogen Bonded Systems with Molecular Dynamics Simulations and Quantum Chemical Methods
… and assess the utility of DMD for the purpose of investigating complex spectral features in N2H+···OC, N2D+···OC, C2O4H-, C2O4D- and (HCOOH)2. The proton transfer as a vibrational motion consists of diffuse qualities that can be accounted for with classical and quantum chemical analyses. Classical …
-
Free vibration and dynamic instability analyses of doubly-tapered rotating laminated composite beams
Due to the outstanding engineering properties, such as high strength/stiffness to weight ratios, capability to be stiff at one location and flexible at another location and favorable fatigue characteristics, doubly-tapered composite beam is used in the rotating structures such as helicopter rotor …
-
A study on pipe bends : an analysis of the smooth pipe bend with flanged end constraints under out-of-plane bending and the development of experimental techniques in the creep of pipe bends
In the design of piping systems the importance of the pipe bend is well established. Recent publications have been increasingly concerned with the effect of end constraints on the behaviour of smooth pipe bends. This has been aimed almost exclusively at in-plane bending, there being no serious …
-
Effects of design details on stress concentrations in welded rectangular hollow section connections
… connections, the “hot spot stress method” in CIDECT Design Guide 8 is widely used. This method forms the basis of various national and international design standards. This thesis sought to address some contemporary design issues where the existing approaches cannot be directly applied. …
-
Stresses and deformations in impulse water turbines
… thesis concerns the theoretical and experimental investigation of the working stresses and deformations in the Turgo impulse wheel and, to a lesser extent, in the Pelton wheel. These wheels are the only impulse water turbines in common use. Directly relevant publications are very few. The most …
-
Rational creep mechanics and engineering applications to high temperature pipework design
The thesis is divided into three sections: The first section is aimed at providing a rational basis for the behaviour of complex structures deforming in time due to creep under the action of arbitrary loading. Two constitutive models were chosen to be studied - the "internal variable theory" and …
-
Study on the Mechanical Properties of Fibre-steered Composites for Aerospace Design Allowables: Investigating the mechanical properties of CTS and AFP manufactured laminates
… to balanced, symmetric, and quasi-isotropic laminates composed of the standard angles 0°, 90°, and ±45°. Whilst convenient and easy to work with, these rules limited the design space to ’black metal’ laminates whereby the laminates take on the same shapes and forms that their metallic …
Page 1 of 2