Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 185 for “"Injection molded"”.
-
High strength injection molded thermoplastic composites
… of blade size on wind generators for example. Injection molding is one of the most versatile methods of producing polymer parts in high quantities and low cost. It is common to use textile on printed films to decorate injected parts. Why not to use carbon or glass fabric reinforcements as an …
-
Injection-molded Thermoplastic Foams for Sound Insulation
… extrusion systems, open-cell foaming with the injection molding process has not received enough attention due to its inherent challenge to produce an open-cell structure. However, despite that challenge, injection molding is one of the most cost-effective and widely used polymer processing …
-
Development of an Injection Molded Boot Adapter
A boot adapter is an injection moulded polymer component intended to isolate a spark plug in a combustion engine used in heavy vehicles. The boot adapter failed too fast either by cracking or electrical puncture and there were large variations of quality among the produced parts. The aim of this …
-
Improved Fiber Orientation Predictions for Injection Molded Composites
Our new orientation model is aphenomenological theory, and the value of the scalar factor to reduce the orientation change rate is determined by matching experimental data. Since the rheology of a fiber suspension is affected by the fiber orientation, a rheological experiment measuring the shear …
-
Fabrication and analysis of injection molded plastic microneedle arrays
… microneedle devices, their fabrication by injection molding, and analysis of the penetration mechanics. Injection molding is an economical mass-production technique that may encourage widespread adoption of microneedles for drug delivery. Four polymers were injection molded into hexagonal …
-
Characterization of injection molded HDPE using SAXS and WAXS
… produced through a manufacturing process called injection molding. The project was carried out in collaboration with Tetra Pak® that uses HDPE as a component in their packages. The aim of the thesis was to characterize the structure of the material HDPE during mechanical deformation. When the …
-
Mechanical behavior and performance of injection molded semi-crystalline polymers.
I have used computer simulations to investigate the behavior of polymeric materials at the molecular level. The simulations were performed using the molecular dynamics method with Lennard-Jones potentials defining the interactions between particles in the system. Significant effort was put into the …
-
Flow line formation of injection molded polypropylene/EP rubber blends
Thesis (M.S.)--Michigan State University. Department of Chemical Engineering, 2001
-
Numerical stimulation of stress-induced crystallization of injection molded semicrystalline thermoplastics
Injection molded semicrystalline plastic products exhibit variable morphology along their thickness directions. The processing conditions have a significant effect on the crystallinity distribution in the final parts. However, because of the lack of sound theoretical models for stress-induced …
-
Process-induced Long-term Deformation Behavior of Injection Molded Semicrystalline Thermoplastics
Process-induced Long-term Deformation Behavior of Injection Molded Semicrystalline Thermoplastics Injection molding is a very complex process because the polymer experiences a complex thermorheological history during molding that influences the molecular orientation, residual stresses, frozen-in …
-
An experimental design approach for predicting shrinkage of plastics injection molded parts
… dimensions and hence the part quality of plastic injection molded parts. In this study, the experimental design approach is used to study the effects of three processing parameters on the shrinkage behavior for along-the-flow and across-the-flow directions of injection molded parts. Multiple …
-
Fiber orientation in injection-molded composites: A comparison of theory and experiment
… of fiber orientation are reported for two parts injection molded from nylon 6/6 reinforced with 43 weight percent of glass fibers. The parts are a center-gated disk and a film-gated strip. Orientation is measured from polished cross-sections and reported as a function of position, both across the …
-
Automated measurement of 3-D fiber orientation distribution in injection molded composites
Thesis (Ph. D.)--Michigan State University. Department of Mechanical Engineering, 1993
-
High Numerical Aperture Injection-Molded Miniature Objective For Fiber-Optic Confocal Reflectance Microscopy
… dissertation presents the design of a miniature injection-molded objective lens for a fiber-optic confocal reflectance microscope. This is part of an effort to demonstrate the ability to fabricate low cost, high performance biomedical optics for high resolution in vivo imaging. Disposable …
-
Modeling of Microstructures and Stiffness of Injection Molded Long Glass Fiber Reinforced Thermoplastics
… has resulted in the growth of the use of injection molded discontinuous fiber-reinforced thermoplastics. During the intensive injection molding process, severe fiber breakage arises in the plasticating stage leading to a broad fiber length distribution. Fiber orientation distribution (FOD) …
-
Fracture and welding of injection molded polypropylene and short glass fiber reinforced polypropylene
Thesis (M.S.)--Michigan State University. Department of Materials Science and Mechanics, 1994
-
Material Characterization and the Effects of Moisture and Drying on Injection Molded Torlon 5030
… of water absorption and drying were studied on injection molded Torlon 5030, a high performance thermoplastic fabricated by Solvay Specialty Polymers. Torlon 5030 contains 30% by weight glass fibers in a polyamide-imide base resin. The objective behind this work was to test and better define …
Page 1 of 10