Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 21 for “"Joint capacity"”.
-
Effects of load proportioning on the capacity of multiple-hole composite joints
… load transmitted by each hole in a multiplehole joint so that the joint capacity is a maximum. Specifically two-hole-in-series joints are examined. The results indicate that when each hole reacts 50% of the total load, the joint capacity is not a maximum. One hole generally is understressed at …
-
Withdrawal and combined load capacity of threaded fastener wood joints
In this study, general models of the capacity of threaded fastener joints were developed from extensive experimental tests. One study objective was to develop a general model of threaded fastener withdrawal strength applicable to joints containing fasteners with widely varying thread geometries. A …
-
Solution of large-scale multicommodity network flow problems via a logarithmic barrier function decomposition
… network flow problem. Placing the complicating joint capacity constraints of the multicommodity network flow problem into a logarithmic barrier term of the objective function creates a nonlinear mathematical program with linear network flow constraints. Using the technique of restricted …
-
Experimental and analytical evaluation of curved bar nodes in reinforced concrete frames joints: strut and tie approach
… This included the determination of the corner capacity and studying the effect of the bend radius at the outside of the frame corners. A total of nine specimens were tested. The specimens were all constructed using ordinary concrete strength (ranges between 4.6 ksi and 5.79 ksi), steel bar …
-
Experimental investigations of shear connections with self-tapping-screws for cross-laminated-timber panels
… connections need to be designed for appropriate capacity, stiffness, and if applied in seismic zones – ductility; however, current North American design standards contain no provisions for STS in CLT. The research developed in this dissertation first examined the withdrawal resistance of STS in …
-
The Performance of Reinforced Concrete Pipe Joints under Differential Ground Settlement
Leakage from reinforced concrete pipe joints has negative environmental impacts and can compromise the sewer or culvert’s service life. Pipes can fracture, corrode, rotate, experience joint pullout, and potentially undergo damage during their installation – leading to leakage into or out from the …
-
The K-group maximum-flow network-interdiction problem
… arcs using limited resources so that the total capacity of uninterdicted arcs crossing between subsets is minimized. The multi-commodity network-interdiction model (MCNIM) explicitly minimizes the maximum amount of flow that can potentially be moved among node groups using K single-commodity …
-
Optimal signaling techniques for crosstalk-dominated communication channels
… rates. We present a framework for maximizing the capacity (or bit rate) of symmetric and asymmetric bit-rate communication services dominated by crosstalk, in particular Digital Subscriber Line (DSL) services. We assume Gaussian noise and crosstalk characteristics, and hence second order …
-
Modeling and Optimization of Resource Allocation in Supply Chain Management Problems
… The third part of the dissertation studies the joint capacity (i.e., resources) and demand allocation problem in a service delivery network. The objective is to minimize the total cost while satisfying a required service reliability, which measures the probability of satisfying customer demand …
-
Investigating the Capacity and Stiffness of Joints used in Gypsum Wallboard Sheathed Light-Frame Wood Shearwalls
… fastened with screws. In total, 270 GWB sheathed joints were subjected to reversed cyclic loading with variations including GWB type, thickness, fastener type, fastener size and manufacturers. The power model type is used to develop the fastener slip equations for nails and screws, which have GWB …
-
Path based p-cycle for resilient MPLS network design : a thesis presented in partial fulfilment of the requirements for the degree of Master of Engineering in Telecommunications and Networking, Massey University, Wellington, New Zealand
… of ring-like recovery speed and mesh-like capacity efficiency. They are suitable for application to the MultiProtocol Label Switching (MPLS) protocol that is widely used in Next Generation Networks (NGNs), in that it provides shared, failure independent, end-to-end protection to whole …
-
DESIGN OF COMPOSITE END-PLATE CONNECTIONS
A study on the behavior of bolted end-plate joints in steel and steel-concrete composite frame structures is presented in this thesis. Bolted end-plate joints are examined extensively in accordance with the most modern code, Eurocode 3 (1992). A design procedure is given in the Annex J of Eurocode …
-
Strengthening T-Joints of Rectangular Hollow Steel Sections Using Through-Wall Bolts and Externally Bonded FRP Plates
T-joints are common in beam-column connections of steel frames, vierendeel girders and at mid-span of N-trusses. Strengthening the members of these structures increases the demand on the joints, which may require joint strengthening. This thesis examines different strengthening techniques of …
-
ANALYTICAL MODELING OF REINFORCED CONCRETE BEAM COLUMN CONNECTIONS FOR SEISMIC LOADING
<p>Reinforced concrete beam column joints are critical members in frame structures they can be subjected to high shear forces under earthquake loading. As a consequence, they can experience high shear and bond slip deformations that contribute significantly to the story drift. Moreover, the joint …
-
Effect of Differential Movement of Straight Reinforcing Bars During Early Age Curing on the Bond Strength
… in differential movements occurring across the joints connecting the elements of these structures. Potential reductions in joint capacity, joint stiffness, and structural durability are the byproducts of these differential movements. The research presented in this paper seeks to address one …
-
Data-driven reconfigurable supply chain design and inventory control
… the resources can be inventory and manufacturing capacity. Our objective is to examine how resource mobility, coupled with data-driven analytics, can result in supply chains that without customer service level reduction blend the advantages of distributed production-inventory systems (e.g., fast …
-
Static Response of FRP Structural Systems – Piles, Platforms, and Poles
… (0ft-lb, 20ft-lb, and 40ft-lb) to establish joint rigidity and find joint failure under different bolt torques and corresponding load-strain and deflection response are plotted. ETABS (FE) modelling was carried out to compare the experimental data. The joint capacity was also determined …
-
Algorithmic Approaches to Battery Consolidation in a Smart Grid
… first problem, we focus on finding an efficient joint capacity and placement planning of BESs among candidate zones and the exchange decisions of EV drivers at a BCS (CPPED) with the aim of minimizing the implementation cost of BESs placement, the distance traveled by EVs to exchange their …
-
Strategic shifts toward regenerative sustainability: The pivotal role of ecological knowledge
… of knowledge and the perspective of absorptive capacity with the notion of ecological knowledge from modern ecology, especially from the social-ecological systems literature, to shed light on the processes through which organizations can effectively access, co-create, integrate and utilize new …
-
Dosage optimization and bolted connections for UHPFRC ties
… In a second part, the idea of a bolted joint connection between UHPFRC elements was proposed. The connection system would be especially useful for struts and ties elements, as truss structures. The possible UHPFRC failure modes were introduced and two different types of tests were …
Page 1 of 2