Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 30 for “"Lightly Reinforced"”.
-
Seismic Design of Lightly Reinforced Concrete Walls
… Canterbury earthquakes in New Zealand, several lightly reinforced concrete (RC) walls in multi-storey buildings formed only a limited number of cracks at the wall base with fracture of vertical reinforcement observed. Initial investigation highlighted that the vertical reinforcement content was …
-
Seismic Design of Lightly Reinforced Concrete Walls in Tall Buildings
… Canterbury earthquakes highlighted that reinforced concrete (RC) walls designed with a low amount of vertical reinforcement are susceptible to sudden failure caused by strain concentration and reinforcement fracture at discrete cracks. Subsequent research resulted in amendment to the …
-
Thin lightly-reinforced concrete walls in concrete shear wall buildings
This thesis focuses on the behaviour of thin and lightly-reinforced concrete walls subjected to axial and lateral in-plane force and displacement demands within high-rise cantilever and coupled shear wall type buildings. Many older and some new high-rise buildings employ thin wall elements of this …
-
Ductility of lightly reinforced and fiber-reinforced concrete elements: A unified approach
Lightly Reinforced Concrete (LRC), Fiber-Reinforced Concrete (FRC), and Hybrid Reinforced Concrete (HRC) elements subjected to static bending actions exhibit a similar behavior, which depends on the amount of rebar and/or fibers added to the cementitious matrix. In all the cases, if a suitable …
-
TORSIONAL EFFECT ON SOFT STORY FOR LIGHTLY REINFORCED CONCRETE STRUCTURES IN LOW SEISMIC ZONES
This study deals with the performance of lightly reinforced concrete moment frames in low seismic zones. The frames under evaluation comprise vertical and/or plan irregularities and were designed for gravity loads only. Nonlinear time history analysis using scaled ground motions and pushover …
-
Shake table Seismic Performance Assessment and Fragility Analysis of Lightly Reinforced Concrete Block Shear Walls
… reports on shake table tests on fully-grouted reinforced masonry (RM) shear walls. The test walls covers a range of design parameters to facilitate benchmarking, a thorough performance investigation, and calibration of numerical models as well as development of fragility curves within the …
-
Experimental and Analytical Investigation of the Dynamic Response of Lightly Reinforced Concrete Frames and Viscoelastic Dampers
… models were used to characterize the behavior of lightly reinforced concrete subassemblages with and without viscoelastic-damped braces and their results were compared with those from the experiments. The VE dampers were found to be effective in improving the response of the lightly reinforced …
-
Investigation of the Use of Viscoelastic Damping Devices to Rehabilitate a Lightly Reinforced Concrete Slab-Column Structure
Interpretations of the testing results are provided through the use of linear models of the type that might be used in the design office. The analytical models were used to assess strength, stiffness, and serviceability of the structure. In addition, the analytical models were used to assess the …
-
A collapse study of a lightly reinforced concrete shear wall building during the February 22, 2011 Christchurch earthquake
… This sequence displayed the vulnerability of lightly reinforced concrete buildings built prior to 1980; specifically, the Pyne Gould Corporation (PGC) building, which collapsed during the February 22, 2011 event in Christchurch, New Zealand. PGC was a lightly reinforced concrete shear wall …
-
Concrete Shear Walls Retrofit by Weakening Through Vertical Cuts and Self-Centering
… explores seismic retrofit of poorly detailed reinforced concrete shear walls by weakening them through vertical and/or horizontal cuts and by adding self-centering through unbonded post-tensioning. Weakening is used to shift failure from brittle to ductile modes. Unbonded post-tensioning is …
-
Influence of Dynamic Load Rates on the Seismic Response of Reinforced Concrete Walls
… number of unexpected failure modes occurred for lightly reinforced concrete walls, such as a lack of cracking in the wall plastic hinge region and premature bar buckling/fracture. In response to these observations, several amendments were made to the New Zealand Concrete Structures Standard, …
-
Behavior of Deep Reinforced Concrete Beams under Monotonic and Reversed Cyclic Load
Non-slender reinforced concrete beams find extensive application in cases where heavy loads need to be transferred over a given span. The safety of this kind of structural elements is often critical for the safety of the structure as a whole. The research described in this thesis is devoted to …
-
CYCLIC BEHAVIOR of HIGH STRENGTH CONCRETE BEAMS
Four high strength, lightly reinforced concrete beams were fabricated and tested to evaluate member response under severe cyclic loading. Concrete strengths varied from 11,310 to 12,860 psi with reinforcement ratios of 0.68 and 1.02%. Nominal stirrup strength was approximately 170 psi for all …
-
Modeling the behavior of shear-critical reinforced concrete columns under lateral loads
Existing reinforced concrete buildings constructed before the development of modern seismic design provisions represent one of the largest seismic safety concerns worldwide. Such buildings are vulnerable to significant damage and even collapse when subjected to strong ground shaking. Collapse of …
-
Nonlinear shear response of cantilever reinforced concrete shear walls with floor slabs
The nonlinear shear behaviour of cantilever reinforced concrete shear walls is complex and not fully understood. Design assumptions often oversimplify the wall response and can yield results which do not reflect the true response of the shear wall. One such assumption is analyzing the wall ignoring …
-
A Risk Based Approach to Module Tolerance Specification
… methodology. This research concludes that over-reinforced or lightly-reinforced designs are not the best solution for mitigating risks, and reducing costs. For this reason the site-fit risk function will provide a range of pareto-optimal building solutions with respect to the fabrication, …
-
The Behaviour and Design of Reinforced and Prestressed Concrete Members Subjected to Torsion
… to obtain a better understanding of how reinforced and prestressed concrete members resist torsion, either in isolation, or when accompanied by shear and flexure. The results were then used to develop practical, easy-to-use tools which are suitable for analysis and design. The main …
-
Studying the Influence of Cracking on The Behaviour of Reinforced Concrete Beams using Distributed Fibre Optic Sensors
… investigated the post-cracking behaviour of reinforced concrete members in flexure and how the shape and pattern of the cracking affected the behaviour. Two experimental campaigns were conducted, the first involving five slender continuous beams and the second three lightly reinforced one-way …
-
DESIGN OF COMPOSITE END-PLATE CONNECTIONS
… bolted end-plate joints. By casting a layer of lightly reinforced concrete on top of the steel beam in a proper way, the joint capacity can be improved significantly. This advantage attracts more and more research interest nowadays. The behavior of composite joints is not understood completely …
-
ANALYTICAL MODELING OF REINFORCED CONCRETE BEAM COLUMN CONNECTIONS FOR SEISMIC LOADING
<p>Reinforced concrete beam column joints are critical members in frame structures they can be subjected to high shear forces under earthquake loading. As a consequence, they can experience high shear and bond slip deformations that contribute significantly to the story drift. Moreover, the joint …
Page 1 of 2