Global ETD Search

Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.

Results

Showing 1 to 20 of 40 for “"Load Distribution Factors"”.

  1. Live load distribution factors for glued-laminated timber bridges

    … with the objective of determining how truckloads are distributed to the structural members of glued-laminated timber bridges. Glued-laminated timber girder bridges with glued-laminated timber deck panels and longitudinal glued-laminated timber deck bridges were the focus of this paper. …

    iastate Repository record for Live load distribution factors for glued-laminated timber bridges (opens in a new tab)

  2. Live load distribution factors for exterior girders in steel I-girder bridges

    … of a complex three-dimensional analysis, live load distribution factors (also referred to as girder distribution factors or wheel load distribution factors) are commonly employed by bridge engineers to simplify the analysis of a bridge system. Specifically, instead of looking at the bridge …

    wvu Repository record for Live load distribution factors for exterior girders in steel I-girder bridges (opens in a new tab)

  3. Live Load Distribution Factors and UHPC Shear Key Performance of SCDOT NEXT-D Beam

    … This leads to a decrease in the transverse load sharing capabilities of these sections. Shear key cracking also leads to reflective cracks developing on the bridge deck, which allows water and other corrosive agents access to the girder reinforcement. APCBGs are often used by SCDOT for short …

    clemson Repository record for Live Load Distribution Factors and UHPC Shear Key Performance of SCDOT NEXT-D Beam (opens in a new tab)

  4. Lateral Load Distribution Factors for Military Vehicles on Multi-Girder Deck Slab Bridge Systems

    … (ASHTO) specifications have prescribed lateral load distribution factors to calculate the bending moments and shear forces for the design of highway bridges for civilian highway traffic. The maximum bending moments and shear forces caused by a wheel line load (or the entire vehicle) placed on …

    vt Repository record for Lateral Load Distribution Factors for Military Vehicles on Multi-Girder Deck Slab Bridge Systems (opens in a new tab)

  5. Load distribution factors of straight and curved steel concrete composite box and I girder bridges

    In the present research, load distribution factors of steel-concrete composite bridges subjected to loads recommended by Australian Bridge Design Code are determined. The bridges can have straight or curved (in plan) alignments with box girder or I girder sectional configurations. The load …

    adelaide Repository record for Load distribution factors of straight and curved steel concrete composite box and I girder bridges (opens in a new tab)

  6. Application of the Grillage Methodology to Determine Load Distribution Factors for Spread Slab Beam Bridges

    Transverse load distribution behavior amongst bridge girders is influenced by many parameters including girder material properties, spacing, skew, deck design, and stiffening element interactions. In order to simply and conservatively approximate the bridge superstructure load distribution between …

    tamu Repository record for Application of the Grillage Methodology to Determine Load Distribution Factors for Spread Slab Beam Bridges (opens in a new tab)

  7. Live load distribution factors for multi-span girder bridges with plank decking subjected to farm vehicles

    … provide simplified formulae to determine Live Load Distribution Factors (LLDFs) for highway bridges. The formulae for the AASHTO code-specified LLDFs have been developed, considering the effect of typical highway trucks. In addition to highway bridges, there are a large number of bridges …

    iastate Repository record for Live load distribution factors for multi-span girder bridges with plank decking subjected to farm vehicles (opens in a new tab)

  8. Live Load Distribution Factors and UHPC Shear Key Performance of SCDOT NEXT D Beam and Solid Slab Bridges

    … to a decreased ability for a bridge to share load among its adjacent members. Both hollow core and solid slab sections are designed to distribute load transversely across the bridge and longitudinally to the girder bearings. Individual girders resist only a portion of the loads on a bridge. If …

    clemson Repository record for Live Load Distribution Factors and UHPC Shear Key Performance of SCDOT NEXT D Beam and Solid Slab Bridges (opens in a new tab)

  9. Development and Validation of Improved Live Load Distribution Factors for Moment in Press-Brake-Formed Steel Tub Girder Bridges

    … the design and analysis of PBFTGs regarding live load distribution factor (LLDF) prediction. Field testing performed on PBFTG bridges showed that the empirical equations found in the American Association of State Highway and Transportation Officials’ Load and Resistance Factor Design Bridge Design …

    wvu Repository record for Development and Validation of Improved Live Load Distribution Factors for Moment in Press-Brake-Formed Steel Tub Girder Bridges (opens in a new tab)

  10. Simplified live-load moment distribution factors for simple span slab on I-girder bridges

    … and assess various methods of computing live load distribution factors and to use the results of laboratory and field tests to compare these methods. It is further a goal of this work to use these methods to perform a parametric study over a wide range of typical slab on steel I-girder bridges …

    wvu Repository record for Simplified live-load moment distribution factors for simple span slab on I-girder bridges (opens in a new tab)

  11. Evaluation, Comparison, and Design of Two Experimental Bridges in Tennessee

    … with the reinforced concrete deck under the live load. After completing a moment comparison analysis, it is concluded that the Massman Drive bridge indeed acts as continuous over the pier as it was designed.</p> <p>This thesis also compares the measured lateral wheel load distribution factors for …

    ut-knoxville Repository record for Evaluation, Comparison, and Design of Two Experimental Bridges in Tennessee (opens in a new tab)

  12. Live-Load Test and Computer Modeling of a Pre-Cast Concrete Deck, Steel Girder Bridge, and a Cast-in-Place Concrete Box Girder Bridge

    … concrete deck, steel girder bridge. A live-load test was performed under the directions of Bridge Diagnostic Inc (BDI) and Utah State University. Six different load paths were chosen to be tested. The recorded data was used to calibrate a finite-element model of this superstructure, which …

    utahstate Repository record for Live-Load Test and Computer Modeling of a Pre-Cast Concrete Deck, Steel Girder Bridge, and a Cast-in-Place Concrete Box Girder Bridge (opens in a new tab)

  13. Bridge Rating Based on In-Situ Weigh-In-Motion and Health Monitoring Data

    … changes from the Allowable Stress Design to the Load Factor Design, and then to the reliability based Load and Resistance Factor Design (LRFD), bridge load rating method has also been evolving. Applying the reliability theory to the bridge load rating is more complex than applying to the LRFD …

    lsu-thes Repository record for Bridge Rating Based on In-Situ Weigh-In-Motion and Health Monitoring Data (opens in a new tab)

  14. Development of lightweight FRP bridge deck designs and evaluations

    … and determine their adequacy under AASHTO's HS25 loading case with minimum stringer spacings of five feet. Two different multicellular decks were designed and tested during this study. Both decks had fiber volume fractions of approximately 54% and weighed 14--15 lb/ft2 of deck area. Testing was …

    wvu Repository record for Development of lightweight FRP bridge deck designs and evaluations (opens in a new tab)

  15. Modeling and Analysis of the DuPont Access Bridge

    <p>This thesis evaluates the lateral wheel load distribution on a two-span experimental highway bridge, examines the continuity of the superstructure over the center pier, and investigates the connection between bridge girders and abutments. Simplified finite element models of the bridge …

    ut-knoxville Repository record for Modeling and Analysis of the DuPont Access Bridge (opens in a new tab)

  16. Design guidelines for FRP honeycomb sandwich bridge decks

    … (1) deck attachment procedures; (2) transverse load distribution factors; (3) local deck deflections; and (4) system fatigue behavior. After the bridge model was tested in the linear range, a 1.2-m wide T-section, of an FRP deck section attached to the middle stringer, was cutout from the bridge …

    wvu Repository record for Design guidelines for FRP honeycomb sandwich bridge decks (opens in a new tab)

  17. Live Load Test and Finite Element Model Analysis of a Box Girder Bridge for the Long Term Bridge Performance Program

    … due to environmental variables and vehicle loads. Part of this program includes the periodic testing of selected bridges. The Lambert Road Bridge was subjected to nondestructive testing in the fall of 2009. Part of this testing included a live load test. This test involved driving two heavy …

    utahstate Repository record for Live Load Test and Finite Element Model Analysis of a Box Girder Bridge for the Long Term Bridge Performance Program (opens in a new tab)

  18. Finite element analysis of multi-channel-beam bridges

    … To study the possible reductions in their load carrying capacities, a number of laboratory and field tests were conducted by Iowa State University. Theoretical analysis, the topic of this paper, was performed to verify the testing results. The PCDBs tested are composed of reinforced …

    iastate Repository record for Finite element analysis of multi-channel-beam bridges (opens in a new tab)

  19. Behavior and design of U-shaped girder bridges supporting heavy railings and sound walls

    … which commonly assume a uniform railing load distribution, may be inadequate for heavy or tall railings, potentially leading to underestimation of girder and overhang forces. This dissertation investigates the structural behavior of prestressed concrete (PSC) U-girder and steel tub girder …

    texas Repository record for Behavior and design of U-shaped girder bridges supporting heavy railings and sound walls (opens in a new tab)

Page 1 of 2