Global ETD Search

Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.

Results

Showing 1 to 20 of 257 for “"Machinability"”.

  1. Machinability of bainitic steels

    … performance. This work investigates the machinability of a bainitic steel intended for trucks and compares it with a quenched and tempered (Q&T) steel currently in use. Both workpiece materials were characterized in terms of microstructure, non-metallic inclusion population and hardness …

    chalmers Repository record for Machinability of bainitic steels (opens in a new tab)

  2. Machinability of bainitic steels

    … Thus, the aim of this thesis is to explore the machinability of bainitic steels and compare it with that of the currently adopted pearlitic-ferritic steels. Both materials were characterized in detail, focusing on microstructure evaluation, examination of non-metallic inclusions, and hardness …

    chalmers Repository record for Machinability of bainitic steels (opens in a new tab)

  3. Machinability of Natural Fiber Composites

    … and wear of the tool. Moreover, the focus on machinability studies thus far has been primarily on optimizing the process parameters and identifying the effects of machinability parameters (namely, cutting speed and feed rate) on machining output responses (delamination and surface roughness). …

    auckland-ms Repository record for Machinability of Natural Fiber Composites (opens in a new tab)

  4. Machinability of 100Cr6 bearing steels

    … at various cutting conditions to investigate the machinability. The tool wear results were then correlated with the material and tool characteristics examined using various methods including light optical microscopy, stereo optical microscopy, hardness testing, scanning electron microscopy, and …

    chalmers Repository record for Machinability of 100Cr6 bearing steels (opens in a new tab)

  5. Machinability of aluminum 7075 alloys

    … and cooling methods influence three key machinability factors: surface roughness, cutting force, and particle emission. In the initial phase of the investigation, all three alloys underwent heat treatment at five different aging times and temperatures. Subsequently, the machining process …

    ets-quebec Download PDF for Machinability of aluminum 7075 alloys (opens in a new tab)

  6. Machinability of stainless steel alloys

    … the optimal cutting parameters that favours the machinability of the tested stainless-steel alloys was made.

    ets-quebec Download PDF for Machinability of stainless steel alloys (opens in a new tab)

  7. On the Machinability of Ductile and Strain Hardening Materials - Models and Methods for Analyzing Machinability

    … on, and to a certain extent predict, the machinability of some common ductile and strain hardening materials. The research has focused on evaluating duplex stainless steel, Ti6Al4V and Alloy 718. However, the proposed models have been constructed in a way as to aid future implementation …

    lund Repository record for On the Machinability of Ductile and Strain Hardening Materials - Models and Methods for Analyzing Machinability (opens in a new tab) Download PDF for On the Machinability of Ductile and Strain Hardening Materials - Models and Methods for Analyzing Machinability (opens in a new tab)

  8. Some Aspects of Machinability Data Optimisation

    … wear is a function of cutting temperature. The machinability data such as cutter life, power required at the cutter, surface finish and vibrations, were obtained using two different face milling cutters (the Walter Cutter and the Sandvik cutter), two different types of tool steel material …

    aston Repository record for Some Aspects of Machinability Data Optimisation (opens in a new tab) Download PDF for Some Aspects of Machinability Data Optimisation (opens in a new tab)

  9. Advances in machinability of gamma titanium aluminides

    … and strong tendency to hardening. Poor machinability and, furthermore, the high manufacturing costs, limit the widespread use of those materials in the market. Moreover, while studies on their machinability with conventional and unconventional processes still require an in-depth …

    poli-torino Repository record for Advances in machinability of gamma titanium aluminides (opens in a new tab)

  10. Machinability Study of Fibre-Reinforced Polymer Matrix Composites

    … research has been devoted to investigate the machinability of these materials in order to elucidate their fundamental machining characteristics. Although much attention on turning and drilling of FRP composites can be traced in the existing literature, only a handful of researchers have …

    auckland-ms Repository record for Machinability Study of Fibre-Reinforced Polymer Matrix Composites (opens in a new tab)

  11. The machinability of a gamma titanium aluminide intermetallic

    The work reported details the machinability of the gamma titanium aluminide intermetallic (-TiAl) Ti-45Al-8Nb-0.2C currently under evaluation to be the material of choice for blades and stators in the intermediate compressor (IP) and low pressure (LP) turbine sections of an aeroengine due to the …

    birmingham Download PDF for The machinability of a gamma titanium aluminide intermetallic (opens in a new tab)

  12. Machinability of Duplex and Super Duplex Stainless Steels

    This master thesis aims at investigating the machinability of duplex, grade 1.4462 and super duplex stainless steels, grade 1.4410 from a tool wear perspective, assessing factors such as cutting forces, chip thickness, and wear evolution. To investigate it, two types of tests were used: orthogonal …

    chalmers Repository record for Machinability of Duplex and Super Duplex Stainless Steels (opens in a new tab)

  13. Machinability of Aerospace Tooling Materials for Composite Repairs

    … production applications is a nickel alloy. Poor machinability and high material costs increase the expense of metallic tooling made from nickel alloys such as `Invar 36' or `Invar 42'. Currently, metallic tooling is unable to meet the needs of applications requiring rapid affordable tooling …

    washington Repository record for Machinability of Aerospace Tooling Materials for Composite Repairs (opens in a new tab)

  14. Machinability study of particle reinforced aluminium metal matrix composites

    In this thesis, machinability of particle-reinforced aluminium metal matrix composites, Comral-85 and DURALCANTM, has been studied. Continuous turning of round composite bars, using polycrystalline diamond (PCD) inserts has been selected as the test method. The test conditions included cutting …

    auckland-ms Repository record for Machinability study of particle reinforced aluminium metal matrix composites (opens in a new tab)

  15. Machinability studies of high strength materials: steel (277 BHN)

    Machinabihty assessment of a high strength steel was carried out using uncoated and coated inserts. The material investigated was steel EN24T/817M40T 277 (BHN). The object of this assessment is to generate reliable machining data in terms of tool life, cutting force and surface finish in relation …

    dcu Download PDF for Machinability studies of high strength materials: steel (277 BHN) (opens in a new tab)

  16. Machinability of Nimonic PE16 for Small Modular Reactor Applications

    … The first goal is to accurately perform a machinability study on the material Nimonic PE16 to create a dataset for analysis and generate machining trends. Secondly, this study aims to create a predictive model to accurately determine the best cutting speeds and feed rates based on critical …

    guelph Repository record for Machinability of Nimonic PE16 for Small Modular Reactor Applications (opens in a new tab)

  17. Characterization, cutting mechanisms and machinability of lead-free brasses

    … breaking), as well as the assessment of the machinability of leaded and lead-free brass alloys, widely used in industrial applications for the fabrication of final brass component (bolts, nuts, hydraulic fittings, valves etc.) by machining.Initially, the influence of microstructure and lead …

    greece Repository record for Characterization, cutting mechanisms and machinability of lead-free brasses (opens in a new tab)

Page 1 of 13