Global ETD Search

Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.

Results

Showing 1 to 20 of 559 for “"Materials--Testing"”.

  1. Materials testing in hypersonic wind tunnels

    <p>The purpose of this investigation was to evaluate a test technique which can be used to provide a test region which duplicates the thermal environment for flight vehicles at supersonic Mach numbers. This technique utilizes a wedge injected into the wind tunnel test section at some nominal angle. …

    ut-knoxville Repository record for Materials testing in hypersonic wind tunnels (opens in a new tab)

  2. Cryostat System for Spacecraft Materials Testing

    … transport, and luminescence of spacecraft materials now has extended temperature control capabilities. By incorporating a two-stage, closed-cycle helium cryostat, it is now possible to simulate the temperature typical spacecraft will experience when in orbit, ranging from < 40 K to > 450 K. …

    utahstate Repository record for Cryostat System for Spacecraft Materials Testing (opens in a new tab)

  3. Refining materials testing methods for chemical and cementitious grouts

    … consistency. However, the lack of standardized testing methods or a lack of understanding in complex rheological behaviors in the industry hinders accurate comparisons and reliable quality control for both cementitious and chemical grouts. This study aims to address this gap. For chemical …

    texas Repository record for Refining materials testing methods for chemical and cementitious grouts (opens in a new tab)

  4. Widefield NV-center quantum sensing for non-destructive materials testing

    … a huge economic loss every year. Non-destructive testing aims to prevent material failure by assessing the material fatigue state without causing any damage. Most nondestructive testing methods are designed for relatively large construction parts and focus on the detection of cracks and …

    freiburg-diss Repository record for Widefield NV-center quantum sensing for non-destructive materials testing (opens in a new tab)

  5. Design fabrication and calibration of MEMS actuators for in-situ materials testing

    … Nickel (Ni) and Gold (Au) are popular thin film materials used in MEMS/NEMS. Various studies have been conducted in recent years to study the mechanical properties of freestanding thin films in situ in TEM to study their failure mechanisms. Some of these studies utilize MEMS devices as actuators. …

    unm Repository record for Design fabrication and calibration of MEMS actuators for in-situ materials testing (opens in a new tab)

  6. Preliminary Materials Testing of Concrete Canvas for Use in Lunar Dust Mitigation Applications

    … (ISRU) infrastructure from regolith-based materials. Upcoming missions will transport and prepare equipment prior to regolith processing and ISRU production. Alternatives for controlled landing surfaces available for early missions have not been proven viable prior to this research. By …

    tamu Repository record for Preliminary Materials Testing of Concrete Canvas for Use in Lunar Dust Mitigation Applications (opens in a new tab)

  7. Microprocessor-based system for the detection and characterization of acoustic emissions for materials testing

    … time. The AEDCS is designed to be used in the AE testing of materials. It is well-suited for non-destructive applications that produce a relatively low AE count rate, such as AE monitoring of wooden structures. The AEDCS is also capable of recording AE event characteristics in destructive test …

    vt Repository record for Microprocessor-based system for the detection and characterization of acoustic emissions for materials testing (opens in a new tab)

  8. Mechanical Testing and Characterization of Proton Irradiated 99.4% NI Using the Reactor Materials Testing Laboratory

    The Queen’s Reactor Material Testing Laboratory uses proton irradiation to simulate the damage induced in a material from neutrons, within a nuclear reactor environment. Inconel X-750 is a 70wt% Ni superalloy, used for the spacer material in the CANDU® reactor. In this work, 99.4% Ni is irradiated …

    queens Repository record for Mechanical Testing and Characterization of Proton Irradiated 99.4% NI Using the Reactor Materials Testing Laboratory (opens in a new tab)

  9. Design of software package for incorporation of random load testing and data processing on materials testing system machine

    … drive and data acquisition system on a Material Testing System (MTS) machine. A microprocessor, combination analog input/output module, magnetic cassette tape recorder, and strain gage network form a strain data acquisition system for recording sequential strain peaks and troughs on specimens …

    nps Repository record for Design of software package for incorporation of random load testing and data processing on materials testing system machine (opens in a new tab)

  10. Research and development of Ayurvastra activewear

    This study integrates materials testing and consumer marketing analysis to establish the foundation for a sustainable activewear brand designed to enhance comfort and alleviate mild physical discomfort. Guided by a modified Design Thinking (DT) framework, the research is organized into three …

    colostate Repository record for Research and development of Ayurvastra activewear (opens in a new tab)

  11. Use of damage lines in predicting cumulative damage in fatigue

    … the period February through May 1953 in the Materials Testing Laboratory of the U. S, Naval Postgraduate School, Monterey, California, The work was undertaken in an effort to test a means of predicting cumulative fatigue life for machine parts subjected to varying loads.

    nps Repository record for Use of damage lines in predicting cumulative damage in fatigue (opens in a new tab)

  12. Development of material models and acquisition of model parameters for metal cutting simulations

    … work material libraries, many engineering materials are not included in them. When the material is not included in the library, the process of testing and characterizing the new material for the simulations is expensive, time consuming and requires a high level of expertise. In this …

    aalto Repository record for Development of material models and acquisition of model parameters for metal cutting simulations (opens in a new tab)

  13. The Design, Construction, Testing and Evaluation of a Strength-of-Material Testing Device

    … purpose of this study was to design, construct, testing and evaluate a strength-of-materials testing device to be used as an appropriate aid to instruction in industrial arts education. In addition to providing a suitable testing device specifically the criteria of size, economy, simplicity of …

    sdstate Repository record for The Design, Construction, Testing and Evaluation of a Strength-of-Material Testing Device (opens in a new tab)

  14. An exact plane-stress solution for a class of problems in orthotropic elasticity

    … Two load cases similar to those encountered in materials testing are investigated using the solution. The solution method developed is seen to have potential uses in stress analysis of composite structures.

    vt Repository record for An exact plane-stress solution for a class of problems in orthotropic elasticity (opens in a new tab)

  15. Design of a data acquisition and reduction system for fatigue testing

    … reduction system has been created for aircraft materials fatigue testing. The system uses HP-9835 Desktop Calculator, an HP-2240A Measurement and Control Processor and a Materials Testing System loading machine. Three different computer programs on the HP-9835 are used to analyze material …

    nps Repository record for Design of a data acquisition and reduction system for fatigue testing (opens in a new tab)

  16. Iterative Learning Control for Precision Motion Control of Microscale and Nanoscale Tracking Systems

    … may change rapidly such as in micro- and nano-materials testing. The time-frequency ILC is applied to a 3-DOF piezo driven flexure stage yielding 4x higher bandwidth over the original feedback controller and achieving 1500 Hz tracking bandwidth during critical partitions of a given trajectory.

    uiuc Repository record for Iterative Learning Control for Precision Motion Control of Microscale and Nanoscale Tracking Systems (opens in a new tab)

Page 1 of 28