Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 20 for “"Microelectromechanical systems Design"”.
-
Testing for delay defects utilizing test data compression techniques
As technology shrinks new types of defects are being discovered and new fault models are being created for those defects. Transition delay and path delay fault models are two such models that have been created, but they still fall short in that they are unable to obtain a high test coverage of …
-
Parylene Microcolumn for Miniature Gas Chromatograph
… of rectangular GC column; second, the design optimization of parylene column and embedded heating element; third, the development of new processes such as parylene micromolding and stationary phase coating technique for parylene column; fourth, the fabrication of parylene GC column with …
-
MEMS micro-bridge actuator for potential application in optical switching
… have been achieved. This microbridge actuator is designed, simulated using ANSYS, fabricated and tested. The results from the testing have shown a good agreement with analytical prediction and ANSYS simulation. The actuator demonstrated bi-stability, two-way actuation and 31µm out-of-plane …
-
Piezoelectrically-Transduced Silicon Micromechanical Resonators
This thesis reports on the design and fabrication of micro-electro-mechanical (MEM) resonators on silicon that are piezoelectrically-transduced for operation in the very high frequency (VHF) range. These devices have a block-type or beam-type design, and are designed to resonate in their in-plane …
-
Advanced sensing technologies : from vanadium dioxide MEMS resonators to polypropylene ferroelectret nanogenerators
… fundamental and applied research studies designed to enable smart material-based advanced sensing technologies including the use of vanadium dioxide (VO2) thin films in resonant frequency tuning methods, and the self-powering/energy harvesting capabilities of polypropylene ferroelectret …
-
Use of decision-centric templates in the design of a separation column for a microscale gas chromatography system
… the interactions unique to microscale devices, designers of microelectromechanical systems (MEMS) require information about complex fabrication and packaging techniques in order to fully complete a successful design. To that end, the successful design of MEMS requires the collaboration of …
-
Characterization of the mechanical properties of freestanding platinum thin films
… material properties. In order to effectively design MEMS devices it is important that these material properties are explored and mechanical behavior of the structure they form be characterized. Popular thin film materials used in MEMS devices are Aluminum (Al), Copper (Cu), Nickel (Ni) and …
-
Monitoring and Control of Semiconductor Manufacturing Using Acoustic Techniques
… and control. A silicon acoustic sensor was designed, fabricated, and implemented as a process monitor. Silicon acoustic sensors are favorable because of their utilization of integrated circuit and micromachining processing techniques; thus, enabling miniature devices with precise dimensions, …
-
Micromachined Components for RF Systems
… especially as frequencies of operation of RF systems continue to increase (and therefore wavelengths continue to shrink).
-
Development of Monolithic SiGe and Packaged RF MEMS High-Linearity Five-bit High-Low Pass Phase Shifters for SoC X-band T/R Modules
… performance of a phased array radar system. The design of the individual phase shifter filter sections, and the influence of bit ordering on overall performance was also addressed. A variety of X-band four- and five-bit phase shifters were fabricated in a 200 GHz SiGe HBT BiCMOS technology …
-
Design and Optimization of Temperature-Stable MEMS Resonators for Timing Applications Based on Thin-Film Lithium Tantalate
… and high turnover temperature, crucial for designing micro-oven-controlled oscillators with excellent stability. Experimental fabrication confirms their high-quality factor (~2000 at 200 MHz), high turnover temperature (>80°C), and moderately large effective electromechanical coupling (~5% …
-
Fabrication of High-Frequency Piezoelectric Resonant Micro-Accelerometers based on Capacitive Loading Effect
… is presented. This novel sensor was designed to operate in 10's of MHz frequency range utilizing an out-of-plane capacitive mechanism for acceleration sensing. The sensor is comprised of a 2-port RF MEMS piezoelectric resonator, operating at 27MHz, and a Capacitive Mass-spring …
-
Monolithic Thin-film Lithium Niobate Scanning Micromirror: Design and Simulation
… piezoelectric medium. In this novel monolithic design, the conventional composite torsional hinges are avoided. The finite element simulations performed and reported in here indicate that the proposed design offers a superior performance in terms of higher scan angle and linear angle control …
-
An Electromagnetic Actuated Microvalve Fabricated on a Single Wafer
… components of the miniaturization of the fluidic systems to control of fluid flow in a variety of applications as diverse as chemical analysis systems, micro-fuel cells, and integrated fluidic channel arrangements for electronic cooling. Using microvalves, these systems offer important advantages: …
-
A Mixed-Signal Low-Noise Sigma-Delta Interface IC for Integrated Sub-Micro-Gravity Capacitive SOI Accelerometers
This dissertation presents the design and development of a mixed-signal low noise second-order integrated circuit (IC) for the open-loop and closed-loop operation of integrated capacitive micro- and nano-gravity accelerometers. The micromechanical accelerometers are fabricated in thick (less than …
-
Characterization of the MEMS directional sound sensor fabricated using the SOIMUMPs process
… the directional sound sensing. The MEMS sensor design considered in this thesis is fabricated using a process by which the sensor has two resonant vibrational modes: rocking and bending. The sensor is simulated using finite element analysis and tested by actuating the sensor using a sound …
-
Design Considerations and Thermodynamic Feasibility Study of a Meso-scale Refrigerator
… of chemical, environmental and energy systems. This foreseeable trend towards miniaturization in chemical, environmental and mechanical systems is expected to revolutionize the ways the human life is being perceived today. The high volume and mass reproducibility is seen as the striking …
-
Development of a compliant micro gripper : a thesis submitted in partial fulfillment for the degree of Masters of Engineering in the School of Engineering and Advanced Technology, Massey University
… of the gripper given an input actuation. Design parameters of the gripper have also been optimised through various techniques such as FEA (finite element analysis) simulation and the effects of altering individual flexure beam lengths. The gripper is operated by a piezo actuator with a …