Global ETD Search

Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.

Results

Showing 1 to 20 of 3176 for “"Milling"”.

  1. Virtual milling

    Milling is used to manufacture a wide variety of metal parts, from simple to complex geometries, in small or large volumes. The requirements for these parts usually necessitate that the milling operation is accurate, but also the production rate must be as high as possible. These two requirements, …

    ubc Repository record for Virtual milling (opens in a new tab) Download PDF for Virtual milling (opens in a new tab)

  2. Reaction forces on a milling tool during three-axis milling

    … a graphical numerically controlled (NC) milling simulation. Graphical simulations give a better feel for what happens during a complicated process, such as NC milling, than does numerical output from a mathematical model. NC milling simulations can be used to verify tool paths, detect …

    iastate Repository record for Reaction forces on a milling tool during three-axis milling (opens in a new tab)

  3. Black Bean Milling

    Black bean milling to produce whole-bean flour and cotyledon flour by using a centrifugal mill and a burr mill/roller milling system, respectively, were investigated. The effect of black bean seed pretreatment (cooked-dried, soaked-dried, and tempered) on flour physical, chemical, and pasting …

    ndsu Repository record for Black Bean Milling (opens in a new tab)

  4. Titanium milling strategies.

    This thesis explores the subject of titanium milling and identifies the need for development of titanium milling strategies to address the key process limitations of chatter and tool wear. These subjects are typically studied in isolation and little work has previously been undertaken on titanium …

    whiterose Download PDF for Titanium milling strategies. (opens in a new tab)

  5. Milling of flexible structures

    … processes. In this thesis, peripheral milling of very flexible cantilevered plates is studied. The static and dynamic deflections of the plate under periodic milling forces are modelled. A new dynamic cutting force model is developed which considers five discrete zones of relative …

    ubc Repository record for Milling of flexible structures (opens in a new tab) Download PDF for Milling of flexible structures (opens in a new tab)

  6. Chatter avoidance in milling

    … The investigation of chatter suppression in milling using continuously variable spindle speed is presented in this thesis. The fundamental mechanism in regenerative chatter is due to favorable phasing between the inner and outer modulations on the chip thickness. In this thesis, the spindle …

    ubc Repository record for Chatter avoidance in milling (opens in a new tab) Download PDF for Chatter avoidance in milling (opens in a new tab)

  7. Dynamics of milling flexible structures

    Peripheral milling of aerospace parts takes a considerable amount of manufacturing time on production floors. Recently, due to fatigue constraints and advances in high speed machining, aircraft components are machined as monolithic parts from solid blanks. This thesis focuses on the mathematical …

    ubc Repository record for Dynamics of milling flexible structures (opens in a new tab) Download PDF for Dynamics of milling flexible structures (opens in a new tab)

  8. Surface Design for Flank Milling

    … to design a curved surface for accurately flank milling with a general tool of revolution is presented. Instead of using the ruled surface as the design surface, the flank millable surface can better match the machined surface generated by flank milling techniques, and provide an effective tool …

    waterloo Repository record for Surface Design for Flank Milling (opens in a new tab)

  9. Dynamics of Low Immersion Milling

    In this thesis, dynamics of low immersion milling is explored through analytical and numerical means. Using linear and nonlinear cutting force models, maps are constructed for single degree-of-freedom and two degree-of-freedom systems where the time spent cutting is "small" compared to the spindle …

    maryland Repository record for Dynamics of Low Immersion Milling (opens in a new tab)

  10. Engraving by CNC milling machine

    … is done using the present technology in a CNC milling machine. This thesis also contains the design of a communication interface between Mark Century One Plus controller and different peripherals. Software for Engraving and Communication between the controller and a PC is developed. The …

    njit Repository record for Engraving by CNC milling machine (opens in a new tab)

  11. Process monitoring in end milling

    <p>Monitoring cutting forces in end milling is a necessary step toward the full automation of milling. To monitor the end milling process successfully, the selection of an appropriate signal and signal processing algorithm is very important. In this research, cutting force trends and tool wear …

    iastate Repository record for Process monitoring in end milling (opens in a new tab)

  12. Computer Adaptive Control in Milling

    … base and an Adaptive Control system for a CNC milling machine. The CNC software base consists mainly of Assembly language routines written for the HP-2100 minicomputer for the editing and debugging of N/C data programs. The Adaptive Control system consists of a cutting force transducer, and an …

    mcmaster Repository record for Computer Adaptive Control in Milling (opens in a new tab)

  13. Reactive Milling of Organic Compounds

    … mineral processing, mechanical treatment by ball milling is an extremely versatile technique for the degradation of toxic compounds. Reactive milling can rapidly destroy organic compounds without producing hazardous wastes. Complete breakdown of the organic molecules is achieved after relatively …

    auckland-tech Repository record for Reactive Milling of Organic Compounds (opens in a new tab)

  14. Tool wear monitoring in face milling

    The purpose of this thesis is to investigate tool wear monitoring using Fourier Series simulation of steady state cutting forces. These simulations show that mean and fundamental values are all that is required to accurately predict immersion and tool wear (high frequency terms are ignored). It is …

    ubc Repository record for Tool wear monitoring in face milling (opens in a new tab) Download PDF for Tool wear monitoring in face milling (opens in a new tab)

  15. Adaptive control of the milling process

    Cutting forces in the milling process vary depending on the work-piece geometry and cutting parameters. When the cutting forces exceed a certain limit, the tool may break and cause damage to the work-piece and eventually to the machine tool. Adaptive cutting force control systems can be used to …

    ubc Repository record for Adaptive control of the milling process (opens in a new tab) Download PDF for Adaptive control of the milling process (opens in a new tab)

  16. Mechanics and dynamics of ballend milling

    Ball end milling has been used extensively in current manufacturing industry in producing parts with sculptured surfaces. Due to its complex cutter geometry, ball end milling mechanics and dynamics have not been studied until recently. In this research, the mechanics and dynamics of cutting with a …

    ubc Repository record for Mechanics and dynamics of ballend milling (opens in a new tab) Download PDF for Mechanics and dynamics of ballend milling (opens in a new tab)

  17. Solid modeller based milling process simulation

    … in sensor design and machine intelligence. Milling operations, however, are largely predictable. Within tolerances, information on the geometry and material properties of the cutter and part is available, and the applicable constraints are known. Indeed, current practice is to use CAD/CAM …

    ubc Repository record for Solid modeller based milling process simulation (opens in a new tab) Download PDF for Solid modeller based milling process simulation (opens in a new tab)

Page 1 of 159