Global ETD Search

Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.

Results

Showing 1 to 19 of 19 for “"Mode-Mix"”.

  1. Experimental measurements of thermal barrier coating interfacial fracture toughness as a function of mode-mix

    Mechanism-based lifetime assessment models of thermal barrier coating (TBC) systems for gas turbine engines rely on accurate knowledge of the experimentally measured interfacial fracture toughness over a range of mode mix and especially at mode-II. Previously no reliable test method had been …

    jhu Repository record for Experimental measurements of thermal barrier coating interfacial fracture toughness as a function of mode-mix (opens in a new tab)

  2. The adhesive interactions between graphene and substrates by blister tests

    … by a full field interference method. Different mixed-mode conditions were achieved by varying the thickness of the backing layers. The measured adhesion energy for the graphene/copper and graphene/silicon interfaces showed a strong dependence on the mode-mix. The deflection profiles were modeled …

    texas Repository record for The adhesive interactions between graphene and substrates by blister tests (opens in a new tab)

  3. A network assignment based approach to modeling mobile source emissions

    <p>Operating mode fractions are among the most important inputs to the mobile source emission inventory studies. This study proposes a methodology to determine alternative operating mode fractions to the outdated operating mode mix derived from the Federal Test Procedure (FTP) driving cycle. The …

    utk-theses Repository record for A network assignment based approach to modeling mobile source emissions (opens in a new tab)

  4. An investigation of vehicle operating mode profiles for use in preparing a high-resolution emission inventory

    … of this investigation was to determine operating mode profiles for vehicles in the cold-start, hot-start and stablized modes on five roadway types, 24 hours of the day, for rural and urban fringe areas. The results are referred to as the New Jersey/California (NJCA) profile. The NJCA profile was …

    ut-knoxville Repository record for An investigation of vehicle operating mode profiles for use in preparing a high-resolution emission inventory (opens in a new tab)

  5. Linking travel demand management and emission estimation tools

    … of the four step travel demand forecasting models for each emission analysis. This could delay the process of approving a transportation program to be included in the State Implementation Plan. To simplify the process of emission impact analysis of TDMs using TDM software, a link between TDM …

    vt Repository record for Linking travel demand management and emission estimation tools (opens in a new tab)

  6. Modeling competing fracture for dry transfer of thin films to a flexible substrate

    … computational analysis with cohesive zone models. Two approaches are used: 2D finite element simulations and 1D finite difference beam theory models. Both mode I and mixed-mode fractures are simulated. Scaling equations are developed to quantify load, crack length, end rotation, damage zone …

    texas Repository record for Modeling competing fracture for dry transfer of thin films to a flexible substrate (opens in a new tab)

  7. Modelling Travel Behaviour with Shared Micro-Mobility Services and Exploring their Environmental Implications

    … users choose between these and more established modes (e.g., public transport, private cars). This thesis contributes by offering some of the first empirical evidence on users, mode choice, substitution patterns and net CO2 emissions of shared micro-mobility services. It goes beyond previous work …

    ethz Repository record for Modelling Travel Behaviour with Shared Micro-Mobility Services and Exploring their Environmental Implications (opens in a new tab)

  8. An Investigation of Interfacial Behaviour in Steel-Concrete Composite System by Cohesive Zone Method

    … between in steel-concrete composite system is modelled with cohesive zone model (CZM). The research objective is to effectively and efficiently model both mechanically connected and adhesive bonded steel-concrete interfaces. A novel tri-linear CZM and an effective damage formulation to account …

    nus Repository record for An Investigation of Interfacial Behaviour in Steel-Concrete Composite System by Cohesive Zone Method (opens in a new tab) Download file for An Investigation of Interfacial Behaviour in Steel-Concrete Composite System by Cohesive Zone Method (opens in a new tab)

  9. Rate-dependent fracture of a silicon/epoxy interface under mixed-mode loading conditions

    … fracture for a silicon/epoxy interface under mixed-mode loading conditions, and the development of a multiscale, mechanism-based model for simulating rate-dependent fracture at interfaces. First, nominally mode-I fracture experiments were conducted with double cantilever beam (DCB) specimens. …

    texas Repository record for Rate-dependent fracture of a silicon/epoxy interface under mixed-mode loading conditions (opens in a new tab)

  10. Controlling fiber/matrix adhesion with binary self-assembled monolayers

    A mixed self-assembling monolayer was applied to a sapphire fiber using two carbon based molecules, Dodeciltrichlorosilane (DTS), and Bromoundecyltrichlorosilane, (BrUTS), in varying ratios. Fibers were cured in an epoxy matrix and pulled in tension to initiate interfacial cracking. The interfacial …

    texas Repository record for Controlling fiber/matrix adhesion with binary self-assembled monolayers (opens in a new tab) Restricted access

  11. Quantitative and consistent tests for interlayer adhesion in laminated glass

    … factors, energy release rate and fracture mode-mix with crack length for the extraction of toughness. Further microscopic analysis of the fracture surfaces elaborated different scenarios to describe the observed fracture mechanisms. At least partial delamination was observed, followed by …

    texas Repository record for Quantitative and consistent tests for interlayer adhesion in laminated glass (opens in a new tab) Restricted access

  12. Understanding cohesive zone models : top-down and bottom-up approaches

    … and packaging. Over the years, cohesive zone modelling has emerged as the natural successor to the classical linear elastic fracture mechanics. Cohesive zone modeling relies on the accurate description of the damage zone through the traction-separation relations relating the effective …

    texas Repository record for Understanding cohesive zone models : top-down and bottom-up approaches (opens in a new tab)

  13. Using far-field measurements for determining mixed-mode interactions at interfaces

    … work is to develop a direct method to extract mixed-mode TSRs using only the far-field measurements. The first topic of the dissertation deals with extracting mixed-mode TSRs based on a combination of global and local measurements including load-displacement, crack extension, crack tip opening …

    texas Repository record for Using far-field measurements for determining mixed-mode interactions at interfaces (opens in a new tab)

  14. Mechanism of Fatigue Crack Growth at Polymer/metal Interface

    … along an Al/epoxy interface was examined under mixed-mode conditions. To provide different combinations of Mode-I and Mode-II conditions, a flexural peel (FP) technique was developed, which proved to be particularly useful for subcritical crack growth studies. Using this technique, fatigue crack …

    uiuc Repository record for Mechanism of Fatigue Crack Growth at Polymer/metal Interface (opens in a new tab)

  15. The notched coating adhesion specimen: a fracture test for coatings and accelerated screening test for adhesion

    … calculations. The specimen geometry results in a mode mix which drives the debond to the interface, thus obtaining a measure of interfacial behavior. Because of the geometry and testing method, the technique is simple, inexpensive and may be conducted quickly. The properties of the coating and the …

    vt Repository record for The notched coating adhesion specimen: a fracture test for coatings and accelerated screening test for adhesion (opens in a new tab)

  16. Characterization of delamination in silicon/epoxy systems

    … However this approach has been unable to model crack-nucleation, which plays an important part in analyzing the mechanical reliability of chip-package systems. The cohesive interface modeling approach, which is considered here, has the capability to model crack nucleation and growth, …

    texas Repository record for Characterization of delamination in silicon/epoxy systems (opens in a new tab)

  17. Durability of Polyimide/Titanium Adhesive Bonds: An Interphase Investigation

    … of an accelerated aging geometry and a mode mix that leads to failure through the interphase, the region of interest. The bulk samples have the advantage of an increased interphase volume and allow for the application of bulk analysis techniques to the interphase, a region that is …

    vt Repository record for Durability of Polyimide/Titanium Adhesive Bonds: An Interphase Investigation (opens in a new tab)

  18. Effect of moisture on mixed-mode TSR on a glass/epoxy interface

    … separation relations and giving rise to the term mixed-mode fracture. This research investigates the effect of moisture on interfacial fracture for different mode-mixes. The content is developed in four parts. First, the adhesive is experimentally characterized via the following tests: mechanical …

    texas Repository record for Effect of moisture on mixed-mode TSR on a glass/epoxy interface (opens in a new tab)

  19. Durability of Polyimide Adhesives and Their Bonded Joints for High Temperature Applications

    … among the three adhesive systems. The effect of mode-mixity on the fracture toughness of the Ti-6Al-4V/FM-5 adhesive bonded system was also evaluated. DCB tests in conjunction with end-notched flexure (ENF) and mixed-mode flexure (MMF) tests, were used to fracture the bonded joints under pure …

    vt Repository record for Durability of Polyimide Adhesives and Their Bonded Joints for High Temperature Applications (opens in a new tab)