Global ETD Search

Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.

Results

Showing 1 to 17 of 17 for “"Notch toughness"”.

  1. Study of Fracture Toughness and Notch Toughness under Impact loading of Electron Beam Melted Ti-6Al-4V alloy

    … a comprehensive investigation into the fracture toughness and the notch toughness behavior of Electron Beam Powder Bed Fused (EB-PBF) Ti-6Al-4V alloy, with particular focus on the effects of build orientation, key mechanical properties and microstructural characteristics. Vertical compact tension …

    washington Repository record for Study of Fracture Toughness and Notch Toughness under Impact loading of Electron Beam Melted Ti-6Al-4V alloy (opens in a new tab)

  2. Embrittlement and Flow Localization of Reactor Structural Materials

    Notch effects have been analyzed utilizing finite element method (FEM) and EBSD misorientation map for unirradiated and irradiated 316L stainless steel. The major issue of interest is the possibility that low ductility, often found following irradiation exposure, will translate into low notch …

    uiuc Repository record for Embrittlement and Flow Localization of Reactor Structural Materials (opens in a new tab)

  3. Evaluation of Temper Embrittlement in 2.25 Cr- 1 Mo Weld Metals Utilizing X-Ray Diffraction.

    … of this type of embrittlement are a reduction in notch toughness, an increase in the ductile-to-brittle transition temperature as measured by Charpy vee-notch impact tests, and a change in fracture mode from ductile transgranular to brittle intergranular.

    uab Repository record for Evaluation of Temper Embrittlement in 2.25 Cr- 1 Mo Weld Metals Utilizing X-Ray Diffraction. (opens in a new tab)

  4. Robust Prediction of Charpy Toughness of Additively Manufactured Kovar Using Deep Convolutional Neural Networks

    … of physical properties, such as fracture toughness, is time consuming and alters the condition of the material, leading to potentially misleading findings. In this study, additively manufactured test coupons were produced over a wide range of process conditions to test the impact toughness …

    unm Repository record for Robust Prediction of Charpy Toughness of Additively Manufactured Kovar Using Deep Convolutional Neural Networks (opens in a new tab)

  5. Mechanical and microstructural properties of ultra-low carbon bainitic steel weld metal

    … power and cover gas. The strength and Charpy V-notch toughness of the resulting welds was investigated. It was found that the GTA weld using 100% argon cover gas had excellent toughness (well above Navy requirements), but the strength was at the minimum specification. The GMA welds using a cover …

    nps Repository record for Mechanical and microstructural properties of ultra-low carbon bainitic steel weld metal (opens in a new tab)

  6. Aboveground fuel oil storage tanks

    … shell stresses. Design limitations imposed by notch toughness and residual stresses are pointed out. Design considerations for the installation of an internal floating roof in a standard cone roof tank are discussed. Methods of calculating evaporation losses and an economic justification for a …

    njit Repository record for Aboveground fuel oil storage tanks (opens in a new tab)

  7. Investigation of heat-affected zone cracking in welded joints of modified HY-80 steel.

    … adjacent to the outer weld passes, showed low notch toughness, high hardness, and in a tensile test did not deform to any appreciable extent without cracking. In fact, the mechanical properties in this area are not greatly different from those of fully hardened base plate, and microscopic …

    nps Repository record for Investigation of heat-affected zone cracking in welded joints of modified HY-80 steel. (opens in a new tab)

  8. Failure mechanisms in surface treated tool steels

    … Izod impact test results indicated reductions in Notch-toughness of between 1.7% to 12.3% for similar coatings to those applied to fatigue testpieces above. The failure mechanisms were also similar to those observed on the fatigue testpieces. Finally slow bend test results showed that, all except …

    aston Repository record for Failure mechanisms in surface treated tool steels (opens in a new tab) Download PDF for Failure mechanisms in surface treated tool steels (opens in a new tab)

  9. Development of Stage-I tempered high strength cast steel for ground engaging tools

    … oxygen melt practice gave 35% improvement in notch toughness. A Mn-Si-Mo-V steel was formulated to minimize solidification shrinkage porosity. Steels were heat treated to a lath martensitic microstructure, and a Stage-I tempered hardness of 53-55 HRC. Yield strength and ultimate tensile …

    must-thes Repository record for Development of Stage-I tempered high strength cast steel for ground engaging tools (opens in a new tab)

  10. Development of an engineering assessment procedure for predicting notch fracture toughness using a constraint-based approach.

    … of a large test programme of Single Edge Notch Bend (SEN(B)) specimens with deep sharp cracks and U-shaped notches. These were used to measure the increase in effective fracture toughness that accompanies increasing notch tip radius. Additional tests of SEN(B) specimens with shallow sharp …

    bristol Repository record for Development of an engineering assessment procedure for predicting notch fracture toughness using a constraint-based approach. (opens in a new tab) Download PDF for Development of an engineering assessment procedure for predicting notch fracture toughness using a constraint-based approach. (opens in a new tab)

  11. Mechanical Behaviour of Cold-formed Hollow Structural Section Material

    … plus heat-treated counterparts.The Charpy V-notch (CVN) impact toughness properties of six RHS specimens were studied via 378 CVN coupons. For RHS with different cross-sectional geometries and produced by different methods, complete CVN toughness-temperature curves of the flat face and the …

    toronto-retro Repository record for Mechanical Behaviour of Cold-formed Hollow Structural Section Material (opens in a new tab)

  12. The effect of welding speed on the properties of ASME SA516 grade 70 steel

    … strength, microstructure, hardness and impact toughness of the specimens were examined. Charpy impact testing was performed according to ASTM E 23 on specimens notched in the weld metal (WM) and in the heat-affected zone (HAZ), to measure the impact toughness. Fractography was performed on …

    sask Repository record for The effect of welding speed on the properties of ASME SA516 grade 70 steel (opens in a new tab)

  13. The Toughness of a Hot Work Die Steel

    … reduction and heat treatment on the fracture toughness of B.S.S. 224 No. 5. nickel-chromium—molybdenum hot work die steel has been determined in the ambient to 500°C. temperature range. Arising from these tests the expected rise in fracture toughness from ambient temperature to 100°C. occurs, …

    aston Repository record for The Toughness of a Hot Work Die Steel (opens in a new tab) Download PDF for The Toughness of a Hot Work Die Steel (opens in a new tab)

  14. Optimalizace tepelného zpracování a volby materiálu průmyslových nožů na zpracování dřeva

    Předložená práce se zabývá řešením problematiky optimalizace tepelného zpracování a volby materiálu průmyslových nožů na zpracování dřeva ve spolupráci s firmou Pilana Tools Knives. Nože této firmy jsou používány v různých částech světa, mimo jiné i v severních státech, kde pracují v extrémních …

    brno-tech Repository record for Optimalizace tepelného zpracování a volby materiálu průmyslových nožů na zpracování dřeva (opens in a new tab)

  15. Využití technologie 3D tisku v automobilovém průmyslu

    Tato diplomová práce se zabývá zkoumáním technologie 3D tisku a její využitelností v automobilovém průmyslu. Rozebírá typy technologií, materiály používané pro 3D tisk, potřebný software a konkrétní možnosti použití. Jeden z materiálů je vybrán a podroben analýze jeho vlastností, poté jsou z něj …

    brno-tech Repository record for Využití technologie 3D tisku v automobilovém průmyslu (opens in a new tab)

  16. Vliv pigmentu na vlastnosti 3D tištěného materiálu metodou DLP

    Diplomová práca sa zaoberá vplyvom pigmentácie na vlastnosti 3D tlačených materiálov vyrobených technológiou DLP (Digital Light Processing). Cieľom práce bolo experimentálne analyzovať, ako rôzne typy a koncentrácie práškových pigmentov ovplyvňujú mechanické, optické a technologické vlastnosti …

    brno-tech Repository record for Vliv pigmentu na vlastnosti 3D tištěného materiálu metodou DLP (opens in a new tab)