Global ETD Search

Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.

Results

Showing 1 to 11 of 11 for “"O-Temper"”.

  1. F-TEMPER VS O-TEMPER BRAZING OF 3003 ALUMINUM RETURN BENDS

    As-extruded (F-temper) 3003 return bends can provide cost savings over annealed (O-temper) return bends in aluminum heat exchangers. To assess if F-temper return bends are an alternative to the baseline O-temper bends, the grain structure, bending performance, and melting behavior were assessed …

    mtu Repository record for F-TEMPER VS O-TEMPER BRAZING OF 3003 ALUMINUM RETURN BENDS (opens in a new tab)

  2. Investigation of effect of temperature and forming speed on the formability of AA3003 Brazing Sheets

    … present work investigates the effect of forming temperature and forming speed on the formability of AA3003 aluminum alloy brazing sheet in three temper conditions (O, H22 and H24) and two different thicknesses (0.2 and 0.5 mm). Limiting Dome Height (LDH) experiments were conducted from which …

    waterloo Repository record for Investigation of effect of temperature and forming speed on the formability of AA3003 Brazing Sheets (opens in a new tab)

  3. A Component-Level Study on the Effect of Warm Forming on Formability and Springback of Aluminum Alloy Brazing Sheet

    … brazing sheet (0.2 mm gauge) for three temper conditions: O-, H22- and H24-tempers. The geometry under study is referred as a surrogate heat-exchanger component (SHC) and contains complex features found on commercial automotive thermal management systems. The hardening behavior of the …

    waterloo Repository record for A Component-Level Study on the Effect of Warm Forming on Formability and Springback of Aluminum Alloy Brazing Sheet (opens in a new tab)

  4. Formability and Failure of Automotive Sheet Material AA5754

    … of AA5754 automotive sheet material in the O-temper, produced via two different processing routes, CC and DC casting, has been investigated by the use of the forming limit diagram (FLD).</p> <p>An in-plane forming test, developed by Marciniak (1973) was used to determine p.p1 {margin: 0.0px …

    mcmaster Repository record for Formability and Failure of Automotive Sheet Material AA5754 (opens in a new tab)

  5. Effect of Forming Temperature and Sheet Temper on the Brazing Characteristics of Aluminum Alloy Sheet

    … research is to understand the effect of forming temperature and initial sheet condition on the brazing performance of Al brazing sheets. The Al brazing sheet used throughout the current work was industrially produced, with an overall thickness of 200 µm, and a single AA4045 clad layer comprising …

    waterloo Repository record for Effect of Forming Temperature and Sheet Temper on the Brazing Characteristics of Aluminum Alloy Sheet (opens in a new tab)

  6. Impact of Manufacturing Pauses in Additive Friction Stir Deposition Aluminum 7075

    … builds were produced using a closed-loop temperature control system, with intentional 15- and 100-hour pauses introduced midway. Some builds were reheated to 120 C before resumption; others restarted without preheating. Structured light scanning evaluated base plate deflection, and neutron …

    utk-theses Repository record for Impact of Manufacturing Pauses in Additive Friction Stir Deposition Aluminum 7075 (opens in a new tab)

  7. Effect of temper conditions on torsional behavior of selected 2000 series aluminum alloys at high strain rates

    … of naturally aged specimens to obtain T651 and O temper condition. The effect of temper conditions on the microstructural evolution in the investigated alloys was investigated. Optical and scanning electron microscopy techniques were used to observe the morphology or composition of the second …

    sask Repository record for Effect of temper conditions on torsional behavior of selected 2000 series aluminum alloys at high strain rates (opens in a new tab)

  8. Strengthening Mechanisms in Microtruss Metals

    … hard anodizing treatments were conducted on O-temper and T8 temper AA2024 truss cores, the strength increase was different for different architectures, but was nearly the same for the two parent material tempers. Finally, the question of how much microtruss strengthening can be obtained for a …

    toronto-retro Repository record for Strengthening Mechanisms in Microtruss Metals (opens in a new tab)

  9. Study of Uniaxial Compression Process for AA7075 Aluminum Alloy

    … conducted to characterize the room and elevated temperature uniaxial compressive deformation behavior of AA7075-T6 and O-temper materials. The experiments consisted of testing cylindrical and cubic specimens prepared from a rolled and heat-treated plate stock of AA7075 alloy. The tests were …

    mcmaster Repository record for Study of Uniaxial Compression Process for AA7075 Aluminum Alloy (opens in a new tab)

  10. Effect of Elevated Temperature on Mechanical Behaviour and Springback of Aluminum Alloy Brazing Sheets

    … AA4045 clad layer used to promote brazing. Three temper conditions were considered including O-, H22- and H24-temper. Two custom tooling sets were designed to form U-shaped channels, allowing forming temperature, blank holding force and lubricant type to be varied. The forming temperature range …

    waterloo Repository record for Effect of Elevated Temperature on Mechanical Behaviour and Springback of Aluminum Alloy Brazing Sheets (opens in a new tab)

  11. Tensile High Strain Rate Behavior of AZ31B Magnesium Alloy Sheet

    … alloy sheets was characterized. Two different temper conditions were considered: AZ31B-O (fully annealed) and AZ31B-H24 (partially hardened). Three different sheet thicknesses were considered for the O temper condition, 1.0, 1.6 and 2.5 mm, while the H24 temper was 1.6 mm in thickness. The …

    waterloo Repository record for Tensile High Strain Rate Behavior of AZ31B Magnesium Alloy Sheet (opens in a new tab)