Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 50 for “"Oil Flow Visualization"”.
-
Investigation of the Flowfield Downstream of a Discontinuous Backward-Facing Step on a Swept Flat Plate
… to improve the understanding of iced swept-wing flow fields. The swept flat plate model included two interchangeable backward-facing steps that were mounted to the full span of the plate leading edge, as well as an adjustable trailing-edge flap. Each of the steps was designed to recreate one of …
-
An experimental study : using honeycomb to reduce secondary flows in curved ducts
… the effectiveness of using honeycomb to improve flow quality by reducing secondary flow in curved ducts. An experimental setup that consisted of two 90° elbows joined by a 6-inch straight connector duct was used. Traditional solid honeycomb and honeycombs of varying porosity (20%, 30%, and 40%) …
-
Some Features of Tip Gap Flow Fields of a Linear Compressor Cascade
… study of three-dimensional turbulent tip gap flows in the linear cascade wind tunnel, for two different tip gap clearances (t/c=1.65% and 3.3%). The experiments focus on near-wall flow field measurements for the stationary wall and moving wall, and static pressure measurement on the low …
-
Aerodynamic characterization of a Griffith-type transonic, laminar-flow airfoil
… Tunnel Facility on a Griffith-type transonic airfoil to evaluate the effectiveness of its laminar flow qualities and boundary-layer flow-control characteristics in the transonic regime. Airfoil surface and wake pressure data were acquired to characterize the aerodynamic performance across a range …
-
Understanding Unsteady Corner Separation Within Wing-Body Junction Flows
Wing-body junction flows, formed at the interface between a wing and fuselage surface, are a complex, coupled, three-dimensional, turbulent flow field. This thesis focused on the unsteady corner separation that develops at the trailing edge of this wing-body junction under certain conditions. A …
-
Performance optimization of a subsonic Diffuser-Collector subsystem using interchangeable geometries
… 3-hole and 5-hole probes were traversed into the flow to generate multiple diffuser inlet and collector exit performance profile plots. Surface oil flow visualization was performed to gain an understanding of the complex 3D flow structures inside the diffuser-collector subsystem. The cutback …
-
Three-Dimensional Shockwave/Boundary-Layer Interactions on Swept Compression Ramps at Mach 4
… number, Reynolds number, and other pertinent flow conditions on the dynamics of 2D and 3D SBLIs. The three model configurations consisted of a high sweep ramp (λ = 27.5 ◦ ), a low sweep ramp (λ =10 ◦ ), and an unswept ramp (λ = 0 ◦ ). All three ramps had a compression angle of 30 ◦ . Oil flow …
-
Investigation of transonic flow separation phenomena on a two-dimensional airfoil
… experimental study was made to investigate flow separation phenomena on airfoils at transonic speeds. The objective of the study was to determine the location and conditions under which local separation and fully separated flow will occur. A wind tunnel test was therefore conducted on a …
-
Aerodynamics of Runback Ice Accretions
… and stalling angle-of-attack of the NACA 3415. Flowfield investigations using fluorescent-oil flow visualization and hot-wire anemometry showed that the simulations that were similar in height to the clean-model local boundary-layer thickness acted to stabilize the recovering boundary layer, …
-
The effects of vortex generating fins and jets on the crossflow separation of a submarine in a turning maneuver
… of fin and jet vortex generators on the crossflow separation of a 688 class submarine in a turning maneuver was studied. The vortex generators are located on the top and bottom centerline of the submarine. The intent of the vortex generators is to improve turning performance by changing the …
-
Boundary Layer Separation Control on a Salient Back-facing Ramp
… feasibility and the performance of the serration flow control devices on a salient edge where the laminar boundary layer separation is two-dimensional. Three geometries of serrations: a sharp delta, a double delta and a divergent delta are examined on 15° and 30° deflected, backward-facing ramps. …
-
A Study of Flow Unsteadiness Due to an Impinging Oblique Shock-Wave Boundary Layer Interaction
… wedge installed on the base of the test section. Oil flow visualization was conducted on the wall opposite the wedge (top-wall) and one of the side walls. Unsteady pressure measurements were acquired on the same top and side walls utilizing pressure transducers. The results revealed a decreasing …
-
Analyzing the flow characteristics of a fluidic oscillator
… water tunnel. Qualitative appreciation of the flow characteristics was gained using dye injection as a method of flow visualization. A second model was machined out of aluminum for testing with air. Quantitative measurements of the flow parameters were obtained with various instrumentation …
-
Strut and wall interference on jet-induced ground effects of a STOVL aircraft in hover
… test rig was used to study the ground plane flow field generated by a STOVL aircraft in hover. The objective of the research was to support NASA-Ames Research Center planning for the Large Scale Powered Model (LSPM) test for the ARPA-sponsored ASTOVL program. Specifically, small scale oil …
-
An experimental investigation of jet-induced ground effects and support strut interference on a STOVL configuration in hover
… and fabricated to study the ground-plane flow field generated by a STOVL aircraft in hover. The objective of the research was to support NASA Ames Research Center's planning for the upcoming large-scale powered model hover tests for the ARPA sponsored ASTOVL program. Specifically, …
-
Iced Airfoil Separation Bubble Measurements by Particle Image Velocimetry
Previous iced airfoil investigations have demonstrated somewhat reduced aerodynamic penalties resulting from a three-dimensional ice simulation, compared to those of a two-dimensional ice simulation of a representative cross section. Correspondingly, the current measurements revealed accelerated …
-
Optimal design of municipal and irrigation water distribution systems
In two-dimensional flow, the point of flow separation from the surface coincides with the point at which the skin friction vanishes. However, in three-dimensional flow, the situation is much more complex and the flow separation is rarely associated with the vanishing of the wall shear stress except …
-
Effects of Mach Number and Flow Incidence on Aerodynamic Losses of Steam Turbine Blades
… total pressure, and endwall static pressures. Flow visualization techniques such as shadowgraph photography and color oil flow visualization were performed to complement the measured data. When the exit Mach number for both nozzles increased from 0.9 to 1.1, the total pressure loss coefficient …
-
A Study of Compressible Turbulent Free Shear Layers Using Laser Doppler Velocimetry (Supersonic Flow, Mixing, Recirculating)
… layers formed by the separation of a Mach 2.43 flow over a backward facing step was conducted. Two different wind tunnel test sections were used to achieve a constant pressure separation of the shear layer at the backstep corner so that the developing free shear layer was unaffected by …
-
High Reynolds Number Turbulent Boundary Layer Flow over Small Forward Facing Steps
… single and 2 point velocity fluctuations and, oil flow visualization. Pressure fluctuation measurements were made 5 boundary layer thicknesses upstream of step to 22 boundary layer thickness (or 600 step heights for smallest step size) downstream of the step. The results show that the steps …
Page 1 of 3