Global ETD Search

Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.

Results

Showing 1 to 8 of 8 for “"Opening Force"”.

  1. Relationship between Peel Force, Opening Force, and Burst Force for a Semi-rigid Cup and Lid, Pre- and Post-Retort

    … if there is any relationship between the peel force, the opening force and the burst force for a semi-rigid cup and lid system, for pre- and post-retort conditions. It also compares the relationship (regression lines) between these forces pre- and post-retort. These seal results were studied by …

    clemson Repository record for Relationship between Peel Force, Opening Force, and Burst Force for a Semi-rigid Cup and Lid, Pre- and Post-Retort (opens in a new tab)

  2. Maximum Opening and Closing Forces Exerted by Diverse Skeletal Types

    … appliance was constructed to measure the maximum opening force, whereas, a gnathodynamometer was utilized to record maximum closing force of 44 subjects. The collected data was analyzed by computer, regardless of sex, to determine both the mean and the standard deviation of the opening forces, and …

    loma-linda Repository record for Maximum Opening and Closing Forces Exerted by Diverse Skeletal Types (opens in a new tab)

  3. Experimental investigation of ASR/DEF-induced reinforcing bar fracture

    … to simulate a fracture of the transverse reinforcement within the time frame of the study and the applicability of various NDT monitoring techniques to detect bar fracture was evaluated. Furthermore, a number of reinforcing bar samples were tested and analyzed to investigate (1) the …

    texas Repository record for Experimental investigation of ASR/DEF-induced reinforcing bar fracture (opens in a new tab)

  4. Modeling, Analysis, and Verification of a Weld-Breaking Mechanism for Automatic Circuit Recloser Applications

    … formed, a mechanism is used to complement the opening force and impart an impact load on the weld. This mechanism is generally designed based on rules of thumb and engineering judgment. This thesis develops a dynamic model of an ACR, which acts as a blueprint for the further development and …

    marquette Repository record for Modeling, Analysis, and Verification of a Weld-Breaking Mechanism for Automatic Circuit Recloser Applications (opens in a new tab)

  5. Design of Novel Endoscopic Suction Grasping and Superelastic Surgical Clips Based on a Novel Model of Thin Collagenous Tissue

    … them. Small grasping jaws cannot distribute force widely enough to apply large forces without tearing tissue, thereby limiting the applied pulling force. Additionally, the surface of tubular organs is smooth, concave, and lubricated, making conventional grasping difficult or requiring hooked …

    toronto-retro Repository record for Design of Novel Endoscopic Suction Grasping and Superelastic Surgical Clips Based on a Novel Model of Thin Collagenous Tissue (opens in a new tab)

  6. Simulation of Fault Characteristics for Commercial Refrigeration Systems via Semi-Empirical Models

    … valve inlet as well as the calculation of the opening force of the TXV from evaporator superheat value. The receiver causes additional modeling errors in comparison to a receiver-less system due to the difficulty in the calculation of two-phase refrigerant properties in the liquid line for some …

    nebraska Repository record for Simulation of Fault Characteristics for Commercial Refrigeration Systems via Semi-Empirical Models (opens in a new tab)

  7. Bistable prestressed spring steel grippers for aerial perching and grasping

    … a single band gripper with a cable driven opening system, then an improved silicone encased single PSSB gripper design. The first single band gripper is experimentally tested to determine the triggering force, effect of offset on triggering force, effect of spring pretension on triggering …

    colostate Repository record for Bistable prestressed spring steel grippers for aerial perching and grasping (opens in a new tab)

  8. Effectiveness of smoke barriers: pressurised stair enclosures

    … was assessed in terms of achieving the door opening force and airflow performance conditions of AS1668.1. This was done using a computer network program known as CONTAM. Initially a base building model was developed, complying with the performance conditions of the Australian Standard and …

    vu-aus Download PDF for Effectiveness of smoke barriers: pressurised stair enclosures (opens in a new tab)