Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 61 for “"Orthogonal cutting"”.
-
Orthogonal cutting of titanium alloys
… of relating the energy required for the orthogonal cutting of titanium alloys with the chip geometry and the mechanical properties of the material, is discussed. The solution is obtained from the extension of the apparent strain analysis of orthogonal cutting of ductile materials to the …
-
Orthogonal cutting in lubricated conditions
The work investigates the role of cutting fluids in metal cutting and comparas their effectiveness in orthogonal cutting conditions. The basic functions of a cutting fluid are defined and the lubricating function is selected as a feasible measure for comparison. The effectiveness of a cutting fluid …
-
Numerical Modeling for Orthogonal Cutting of Brittle Materials
… However, the models of brittle materials cutting are not yet well-established. The difficulty of modeling such a process can be attributed to the crack initiation and propagation governed by fracture mechanism. A brittle cutting generally produces powder-like chips, fragmented and dusty …
-
Incipient Plastic Deformation in Orthogonal Cutting of 70/30 Brass
Made available in DSpace on 2014-12-09T17:13:51Z (GMT). No. of bitstreams: 1 7013533.pdf: 5026912 bytes, checksum: 091b1dfe2c68710de23f3d57cdc89fb2 (MD5) Previous issue date: 1969
-
Numerical modeling of orthogonal cutting of carbon fibre reinforced polymer composites
The focus of this study is on the orthogonal cutting of fibre reinforced composites. A thorough review of the literature is presented in both experimental and numerical work that has thus far been conducted. It is found that in orthogonal cutting of composites, cutting forces, chip formation …
-
FEM for the Determination of Temperature Distribution in Orthogonal Cutting Process
The study of metal cutting process is primarily aimed at reducing production cost. One way of reducing the cost of production would be to increase the speed at which metal is cut. However, since operating at high speed is found to decrease the tool life, an economic balance which takes into account …
-
A Thermal-Mechanical Finite Element Analysis of Orthogonal Cutting for Normalized Steels
… analysis is performed in order to simulate orthogonal cutting of normalized steels. The Johnson-Cook cook material and damage parameters are utilized to define the behavior and failure of the material. Four cases are simulated with workpiece materials of A2024-T351, AISI 1045, AISI 4140, and …
-
Prediction of Hardness and Residual Stress in Orthogonal Cutting of Inconel 718
… alloy with poor machinability. For instance, the cutting force is high in cutting Inconel 718, resulting in work-hardening of the machined surface and high residual stress in the machined surface. When residual stress releases, the part deforms and scrapes with error beyond tolerance. Therefore, …
-
Advanced modelling for the orthogonal cutting of unidirectional carbon fibre reinforced plastic composites
… methodologies to improve the simulation of the orthogonal cutting of unidirectional carbon fibre reinforced plastic (UD-CFRP) composites. In a meso-scale approach, a new cohesive model was developed to overcome the excessive deformations shown by the generally implemented zero thickness cohesive …
-
MACHINABILITY STUDY AND FEM ANALYSIS OF UD-CFRP COMPOSITE MTM 44-1 MATERIAL UNDER ORTHOGONAL CUTTING CONDITION
… a number of process parameters and relative cutting forces generated during the machining process. A Finite Element Model (FEM) was created to predict cutting forces during orthogonal cutting of Unidirectional Carbon Fibre Reinforce Polymer (UD-CFRP) composite material. The material analysed …
-
The influence of aluminium additions on titanium during machining through the application of a novel orthogonal cutting test method
… behaviours such as yield stress. A novel orthogonal cut test was successfully developed to generate deformation behaviour from high speed milling and flow behaviour from axisymmetric compression tests in a single test method. This suggests the potential to incorporate `machinability' …
-
Mechanics of machining zirconium-based bulk metallic glass
… model of chip formation is developed for orthogonal cutting of Zirconium (Zr) - based BMG considering the process kinematics, material constitutive law, heat, and free volume evolution. The model predicts the segmented chip formation, oscillations of stress and temperature in the primary …
-
Microstructure -Level Machining Modeling of Ferrous Alloys
… two of its constituents: pearlite and ferrite. Orthogonal cutting experiments and simulations were conducted of the three materials. The measured chip morphology and machining forces were compared with the model predictions, and a good correlation between them was found. In addition, the …
-
High bandwidth cutting force measurement during the cutting of aa 7075-t6 and its application to measure the evolution of flow stress within developing shear bands
… called shear bands. Shear bands occur in metal cutting when material deformation in the primary shear zone is accompanied not by hardening but by weakening, by ductile damage and/or thermal softening by adiabatic heating. Recent work [1] has shown that the force supported by shear bands induced …
-
A generalized approach for mechanics of chip formation in steady-state and dynamic orthogonal metal cutting using a new model of shear zone with parallel boundaries and its validation to cutting-forces prediction in self-piloting machining
… parallel-sided shear zone models. A steady-state cutting force model has been derived and adapted to orthogonal cutting of a self-piloting drilling. In the formulated model, special attention has been devoted to the thermomechanical state which defines the effect of the temperature on the yield …
-
A study of heat fluxes in oblique cutting of A390 using infrared imaging and inverse heat conduction
The energy released during mechanical cutting is carried away by the metal chips and conduction into the tool. This report focuses on determination of the heat fluxes into the tool during orthogonal cutting using Beck's method. An infrared camera is used to measure the temperature rise on the …
-
Investigation of the effect of tool geometry on the machining process
Cutting tool geometries play important roles in tool performance, such as tool life, surface integrity, and cutting force. The most common commercial tools edge geometries are honed, chamfered and hone-chamfered. This study investigates new ways to develop tool geometry. An uncoated carbide tool is …
-
A study of the cutting forces and vibration characteristics in titanium machining
… of titanium machining is presented in terms of cutting mechanics and dynamics. An experimental study examines the effects of the cutting parameters on the machining process of titanium alloy Ti6Al4V, as well as chatter vibration. The chip formation in near-orthogonal cutting transits from a …
-
PROCESS-INDUCED SURFACE INTEGRITY IN MACHINING OF NITI SHAPE MEMORY ALLOYS
… which give significant reductions of tool-wear, cutting forces, and surface roughness. The influence of machining process conditions, including dry, MQL, preheated, cryogenic machining, and the effects of prefroze cryo machining on surface integrity characteristics such as microhardness, phase …
Page 1 of 4