Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 120 for “"Pearlite"”.
-
Fatigue in pearlite structures.
… were produced in the steel,these being coarse pearlite,;fine pearlite and spheroidised carbide.Pearlite structures were selected because of their practical importanceand also because multi-phase alloys have, until recently, receivedlittle attention from research workers.Specimens were fatigued …
-
Kinetics of the pearlite to austenite reversion transformation
The pearlite-to-austenite reversion transformation kinetics under isothermal and continuous heating conditions in a eutectoid plain-carbon steel have been measured, using a dilatometric technique on a Gleeble 1500 Thermomechanical Simulator. The isothermal data was characterized in terms of the …
-
Induction hardening response of ferrite and pearlite banded steel
Includes bibliographical references (pages 127-133).
-
Thermodynamics and Kinetics for the Pearlite Reaction in Chromium Steels
… system, essential for the understanding of the pearlite reaction in low chromium steels, has been calculated from the thermodynamic data. The experimentally determined tie-lines are in good agreement with the calculated phase diagrams.</p> <p>The pearlite growth rates and interlamellar spacings …
-
Effect of microalloying on pearlite transformation of high carbon wire steels
… eutectoid steels showed delayed pearlite transformation with additions of niobium and accelerated pearlite transformation with additional nitrogen. This study investigates the origin of the CCT shifts with microalloying additions and whether trends in hardness and microstructural …
-
The Beta transformation in brass and the physical structure of pearlite
Thesis (M.S.)--Michigan State College of Agriculture and Applied Science. Dept. of Chemical Engineering, 1938
-
Static strain aging in low carbon ferrite-pearlite steel : forward and reverse loading
… a low carbon steel (0.16 wt% C) with a ferrite-pearlite microstructure. Torsion tests on hollow tubular samples were used for the mechanical tests. The shear strain on the surface of the sample was measured with the digital image correlation. The influence of the amount of pre-strain, aging time …
-
Effects of vanadium microalloying of 1080 steel on pearlite transformation kinetics and microstructural development
The effects of V alloying on the pearlite transformation kinetics and microstructure in 1080 steel were evaluated. Two industrial wire rod steels, 1080 and 1080V with a 0.035 wt pct V addition, were isothermally heat treated using dilatometry to assess pearlite transformation rates. A detailed …
-
Mathematical modelling of the onset of transformation from austenite to pearlite under non-continuous cooling conditions
… the start of transformation from austenite to pearlite has been developed based on the assumption of the consumed fractional incubation time being additive. The curve is characteristic of the chemistry and the austenite grain size of the steel. A mathematical relationship between the …
-
The effects of certain trace elements on carbides and pearlite during the heat treatment of ductile iron
Electronic Thesis or Dissertation
-
Effects of forging on the microstructural development, strength, and dynamic fracture behavior of microalloyed ferrite-pearlite steels, The
Includes bibliographical references.
-
Effect of ferrite and pearlite banding on the rotating bending fatigue behavior of induction hardened 4140Ca4 bar steel, The
Includes bibliographical references (pages 95-97).
-
Calorimetric Measurements on High Purity Iron and Eutectoid Steels
… is, during the transformation of austenite to pearlite at temperatures well below the critical temperature, the problem was approached from the reverse transformation. The specific heat of the pearlite and austenite are known throughout the temperature range over which the transformations are …
-
Experimental investigation of microstructure and properties in structural alloys through image analyses and multiresolution indentation
… are performed on small volume ferrite-pearlite steel samples that were excised from in-service gas turbine components after prolonged exposure (up to 99,000 hours) to elevated temperatures, which promotes microstructural changes (spheroidization of pearlite and graphitization) as well …
-
The correlation of microstructure with the strength and fracture toughness of pearlitic steels
… In Part 1, the influence of various ferrite-pearlite microstructures on the hardness and flow stress has been examined with respect to a Hall-Petch analysis. In contrast with previous reports it was found that a Hall-Petch equation can be applied satisfactorily in describing these properties …
-
Computer-Aided Estimation of Steel Hardenability On the Basis of Alloy-Chemical Composition
… including the latent heat evolution of the pearlite reaction has been developed to predict thermal conditions in a Jominy bar. This has been combined with a model for pearlite nucleation and growth developed by Kirkaldy and used to predict the TTT curves for the austenite → pearlite …
-
Intergranular and transgranular stress corrosion cracking of carbon steel in fuel-grade ethanol
… with pure MnS. The selective dissolution of pearlite nodules was studied by making cathodic polarization measurements with pure iron and cementite. Clear differences were found between the intergranular and transgranular SCC mechanisms. With negligible chloride concentrations the …
-
EFFECTS AND LIMITATIONS OF RESIDUAL ALLOYING ELEMENTS IN SILICON SOLID SOLUTION STRENGTHENED FERRITIC DUCTILE IRON
… because of the need to reduce the amount of pearlite promoting elements, particularly copper and manganese, which are used in traditional grades. Knowing the acceptable threshold of residual alloying elements will allow for more cost-effective tailoring of the charge stream. Data were …
-
Machine Learning Based Ultra High Carbon Steel Image Segmentation
… microstructures composed of constituents such as pearlite and spheroidites. Locating micro constituents and quantitatively measuring its presence is key for material researchers to study the physical properties of the carbon steel materials. This micrograph analysis is currently done manually and …
Page 1 of 6