Global ETD Search

Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.

Results

Showing 1 to 20 of 21 for “"PolyMUMPs"”.

  1. A PolyMUMPs Capacitive Micromachined Ultrasonic Transducer

    … electrodes and their fabrication using the PolyMUMPs technique provided by MEMSCAP Inc. It also reports a new behavioral model of the CMUTs written in VHDL-AMS, complemented by a comparison between finite element analysis, behavioral simulations and experimental measurements on the newly …

    ubc Repository record for A PolyMUMPs Capacitive Micromachined Ultrasonic Transducer (opens in a new tab) Download PDF for A PolyMUMPs Capacitive Micromachined Ultrasonic Transducer (opens in a new tab)

  2. MEMS polymumps-based miniature microphone for directional sound sensing

    … employed in this thesis was fabricated using the PolyMUMPs process. The sound sensor has two primary vibrational modes (rocking and bending) which were simulated by finite element analysis and tested by actuating the sensor using both electrostatics and sound. The experimentally observed …

    nps Repository record for MEMS polymumps-based miniature microphone for directional sound sensing (opens in a new tab)

  3. Fabrication, Testing and Characterization of MEMS Gyroscope

    … fabrication using MEMSCAP's SOIMUMPs and PolyMUMPs processes is described. For the former, post-processing was carried out at the Quantum Nanofab Center (QNC) on a die-level in order to create the vibratory structural elements (cantilever beam). Following this, the PolyMUMPs gyroscopes are …

    waterloo Repository record for Fabrication, Testing and Characterization of MEMS Gyroscope (opens in a new tab)

  4. Fabrication and Study of AC Electro-Osmotic Micropumps

    … discrete electrode arrays was made using PolyMUMPs® process. The breakthrough of this work was discretizing the continuous 3D stepped electrodes which were commonly seen in the past research. The “T-shaped” electrodes did not only create ACEO flows on the top surfaces of electrodes but …

    queens Repository record for Fabrication and Study of AC Electro-Osmotic Micropumps (opens in a new tab)

  5. Design optimization of a microelectromechanical electric field sensor using genetic algorithms

    … designs were modified for fabrication using the PolyMUMPs abrication process but failed to operate due to the process. In order to fabricate the sensors in-house with a silicon-on-glass process, an anodic bonding apparatus has been designed, built, and tested.

    manitoba Repository record for Design optimization of a microelectromechanical electric field sensor using genetic algorithms (opens in a new tab)

  6. MEMS ultrasonic sensors for anemometry applications on MARS

    … available surface micromachining technique, PolyMUMPs. PolyMUMPs process from MEMSCAP inc. is a three-layer polysilicon surface micromachining process. The CMUT devices proposed in this thesis make use of two out of three polysilicon layers. COMSOL Multiphysics simulations were used to …

    manitoba Repository record for MEMS ultrasonic sensors for anemometry applications on MARS (opens in a new tab)

  7. Electro-Thermal Mechanical Modeling of Microbolometer for Reliability Analysis

    … testing of Polysilicon Multi-User MEMS Process (PolyMUMPs®) test devices as the groundwork for the investigation of microbolometer performance and reliability in space applications. An electro-thermal analytical and numerical model was developed to predict the temperature distribution across the …

    waterloo Repository record for Electro-Thermal Mechanical Modeling of Microbolometer for Reliability Analysis (opens in a new tab)

  8. 3D MEMS Microassembly

    … The microcomponents were fabricated using PolyMUMPS, a part of the Multi-User MEMS Processes (MUMPS), and experimentation was conducted with the goal of constructing a 3D microstructure. The results were partially successful in that both grippers were able to pick up corresonponding parts …

    waterloo Repository record for 3D MEMS Microassembly (opens in a new tab)

  9. Design and Analysis of a MEMS Fabry-Perot Pressure Sensor

    … pressure for pressures below 40 psi. For the PolyMUMPs fabricated sensors, the error is less than 4% for pressure values smaller than 40 psi.

    waterloo Repository record for Design and Analysis of a MEMS Fabry-Perot Pressure Sensor (opens in a new tab)

  10. Capacitive Micromachined Ultrasonic Transducers: Design, Fabrication and Characterization

    … resonant frequencies, were fabricated using a PolyMUMPs sacrificial technique. An analytical and finite element model was used to further understanding of the physical behaviour of the transducer. The basic functionality of the CMUT devices was investigated through capacitance and electrical …

    manitoba Repository record for Capacitive Micromachined Ultrasonic Transducers: Design, Fabrication and Characterization (opens in a new tab)

  11. Characterization of multiple moving membrane capacitive micromachined ultrasonic transducer

    … arrays of these devices were fabricated using PolyMUMPs technology, a sacrificial fabrication technique for the MEMS transducers. The electrical and acoustic characterizations of the fabricated devices were performed to measure the actual transducer properties. The measured data and the model …

    manitoba Repository record for Characterization of multiple moving membrane capacitive micromachined ultrasonic transducer (opens in a new tab)

  12. Modeling, Design, and Testing of an Underwater Microactuation System Using a Standard MEMS Foundry Process

    … fabricated with a MEMS fabrication process, PolyMUMPS. This work also shows the development of an elliptic integral model to analyze the compliant fixed-guided beams in the TIM and gives new insight into the buckling behavior, reaction forces, and displacement of the beams. The derivation, …

    byu Repository record for Modeling, Design, and Testing of an Underwater Microactuation System Using a Standard MEMS Foundry Process (opens in a new tab) Download PDF for Modeling, Design, and Testing of an Underwater Microactuation System Using a Standard MEMS Foundry Process (opens in a new tab)

  13. Novel RF MEMS Varactors Realized in Standard MEMS and CMOS Processes

    … MEMS variable capacitors are built by the PolyMUMPs process. The fifth novel parallel-plate MEMS varactor has thin-film vertical comb actuators as its driver. Such an actuator can vertically displace both plates of the parallel-plate capacitor. By making use of the fringing field, this …

    waterloo Repository record for Novel RF MEMS Varactors Realized in Standard MEMS and CMOS Processes (opens in a new tab)

  14. Design and analysis of capacitive micromachined ultrasound transducer

    … that the CMUTs are to be fabricated using PolyMUMPs technology, for this technology being precise, accurate and well established in the micro-electromechanical systems (MEMS) community. CMUTs were first analytically modeled and designed by exploiting the parallel-plate capacitor equations. …

    ubc Repository record for Design and analysis of capacitive micromachined ultrasound transducer (opens in a new tab) Download PDF for Design and analysis of capacitive micromachined ultrasound transducer (opens in a new tab)

  15. Design and evaluation of CMUTs for medical ultrasound imaging with a focus on non-invasive blood pressure waveform monitoring

    … First, four CMUT topologies fabricated in a PolyMUMPs process are studied, combining spring versus straight arms with rocker versus fixed anchoring. Laser Doppler vibrometer in air and vacuum is used to extract resonance frequency and quality factor as a function of dc bias and ac drive. A …

    ets-quebec Download PDF for Design and evaluation of CMUTs for medical ultrasound imaging with a focus on non-invasive blood pressure waveform monitoring (opens in a new tab)

  16. Rotary micro-electro-mechanical scanner for chip-level beam steering application

    … actuation was designed and fabricated using the PolyMUMPS process to implement the rotary platform. Various micro-polyhedron of different size for beam deflection were designed and fabricated using the PiezoMUMPS process and a simple integration technique was developed to mount these …

    ets-quebec Download PDF for Rotary micro-electro-mechanical scanner for chip-level beam steering application (opens in a new tab)

  17. Microactuators and their application in micro-opto-electro-mechanical systems (MOEMS)

    … and fabricated by surface micromachining using PolyMUMPs (Polysilicon Multi-User MEMS Processes) foundry process. The principle is simply interrupting the light beam by a vertical microshutter. An array of SDAs have been used to drive the microshutters. Microhinges are employed to build the …

    strathclyde Repository record for Microactuators and their application in micro-opto-electro-mechanical systems (MOEMS) (opens in a new tab)

  18. MEMS based atomic scale 3D printer for nanofabrication

    Additive manufacturing is revolutionizing the aerospace, transportation, energy, healthcare and various consumer product industries, replacing centralized manufacturing plants with more localized fabrication. 3D printing has become ubiquitous within these industries for prototyping and production. …

    bu Repository record for MEMS based atomic scale 3D printer for nanofabrication (opens in a new tab)

  19. Optical MEMS Switches: Theory, Design, and Fabrication of a New Architecture

    … of the 3DRIM was achieved after several PolyMUMPs fabrication runs. The new switch architecture is neither 2-D nor 3-D. Since it is composed of two layers, it can be considered 2.5-D. The new switch overcomes many of the limitations of current traditional 2-D MEMS switches, such as …

    waterloo Repository record for Optical MEMS Switches: Theory, Design, and Fabrication of a New Architecture (opens in a new tab)

  20. A Multifunctional MEMS Pressure and Temperature Sensor for Harsh Environment Applications

    … the new sensing mechanism fabricated using the PolyMUMPs® foundry process were tested to verify its thermal behavior up to 125 °C. The experiments were performed using a ceramic heater mounted on a probe station with the device connected to a precision LCR-meter for capacitive readouts. …

    waterloo Repository record for A Multifunctional MEMS Pressure and Temperature Sensor for Harsh Environment Applications (opens in a new tab)

Page 1 of 2