Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 394 for “"Pressure Loss"”.
-
Effect of cuttings on annular pressure loss
Accurate measurements of pressure loss in the annulus are critical in order to optimize drilling operations and to ensure a safe drilling environment. Monitoring Equivalent Circulating Density (ECD) is essential because it ensures that the applied dynamic fluid pressure is within the drilling …
-
Develop Design Data on Pressure Loss of Large Pipe Fittings
Pressure loss coefficients were determined for large radius ells, large concentric pipe reducers, and expansions, as well as large pipe tees. The fittings tested were 12, 16, 20, and 24 inch forged steel weld. Forty individual fittings from four different manufacturers were tested to determine loss …
-
Pressure loss associated with flow area change in micro-channels
Pressure drop across miniature-scale flow disturbances, including abrupt flow area changes, is an important source of error and confusion in the literature. Such pressure drops are frequently encountered in experiments, where they are often estimated using methods and correlations that have been …
-
Static Pressure Loss in 12”, 14”, and 16” Non-metallic Flexible Duct
… to determine the effects of compression on pressure drops in non-metallic flexible duct. Duct sizes of 12”, 14” and 16” diameters were tested at a five different compression ratios (maximum stretch, 4%, 15%, 30% and 45%) following the draw through methodology in ASHRAE Standard 120 -1999 – …
-
Pressure loss modeling of non-symmetric gas turbine exhaust ducts using CFD
… numerical analysis were used to develop a total pressure loss model. These exhaust ducts comprise an annular inlet, a flow splitter, an annular to rectangular transition region, and an exhaust stub. The duct geometry, which is a three-dimensional complex one, is approximated with a five-parameter …
-
Aerodynamic Force and Pressure Loss Measurements on Low Aspect Ratio Pin Fin Arrays
… pin fin arrays comes at the expense of increased pressure drop. Therefore the pin fin geometry must be judiciously chosen to achieve the required heat transfer rate while minimizing the associated pressure drop. This project culminates in the measurement of both pin fin force and array pressure …
-
A Cfd model to predict pressure loss coefficient in circular ducts with a motorized damper
The pressure loss coefficient was determined for a circular duct with a circular damper using computational fluid dynamics. The CFD package Star-CD was used to predict the air flow and pressure distribution in the duct. A three dimensional computational fluid dynamics model was developed and …
-
Experimental Investigation on Heat Transfer and Pressure Loss Characteristics of Rotating Rectangular and Annular Ducts
… assembled. In this study, the heat transfer and pressure loss characteristics of two of these passages are investigated experimentally. The first of the two passages investigated is the passage in between the turbine blade root and disc. This passage has a unique geometry resembling an S-shape. …
-
Measurement of the heat transfer coefficient and viscous pressure loss for mercury flowing in narrow channels
<p>The Spallation Neutron Source (SNS) is a new linear accelerator that is being designed for neutron scattering experiments. The SNS will supply pulses of high-energy protons to a flowing liquid mercury target. The spallation reaction resulting from the bombardment of the protons on the mercury …
-
Pressure Loss Coefficients for Large Mitered Elbows with Diameters Ranging from 36-inches to 144-inches
… system, it is important to understand the pressure losses that will occur within the system. One common source of pressure loss is from elbow pipe fittings. There is extensive research available for pressure loss coefficients of elbow pipe fittings, but the research is derived from elbows …
-
Numerical Investigation of a sub-1 kN Turbojet Combustor: Quantification and Reduction of the Combustor Pressure Loss
… of a small turbojet combustor to determine total pressure loss and its impact on specific thrust and thrust-specific fuel consumption. Manufacturer specifications were used to estimate key thermodynamic states, which served as boundary conditions for a cold-flow CFD simulation in ANSYS CFX. The …
-
Improved Pressure Loss And Multiphase Flow Behavior Predictions For In-Line Gas-Liquid Contactors Using Experimental Measurements And CFD Simulations
… for counter-current service. Unfortunately, the pressure loss correlations available to the design engineer are sparse and only valid up to Re_G<50,000. In contrast, most gas pipelines operate in the range of 10^5
-
Evaluation of an in-house GPU based CFD solver
… are used. One evaluated flow parameter is total pressure loss. The pressure loss is presented in three different ways with respect to the inlet swirl angle, using a so called loss bucket and also two factors with normalized result. The two normalized factors are called off-design factor and loss …
-
A systematic approach to evaluate in-stope compressed air inefficiencies in deep-level mines
… and the effect thereof on drilling pressure. The study provides a verified method for identifying compressed air inefficiencies inside the stoping area and evaluating the viability and efficacy of various approaches to address in-stope compressed air inefficiencies. A method is …
-
Experimental investigation of reversed flow in a compressor cascade
… The investigation included total and static pressure measurements upstream and downstream of the cascade as well as blade surface measurements. Aerodynamic performance parameters were presented for a reversed flow cascade. Comparison of corrected total pressure loss curves suggested that …
-
Pressure losses at bends and junctions
… whether the CFD simulations could yield accurate pressure loss data for input into a one-dimensional engine simulation code. The experiments were carried out on a steady flow rig, and three bends with varying degrees of curvature, a T-junction, and a Y-junction were tested. The experiments covered …
-
Flow and Heat Transfer in Tubes with Obstacles
… enhance the understanding of heat transfer and pressure loss in heated tubes equipped with flow obstacles by experimentally investigating the axial and circumferential distributions of convective heat transfer in a heated tube, complemented by pressure loss and velocity measurements in an …
Page 1 of 20