Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 39 for “"Pressure Probes"”.
-
Calibration and data reduction algorithms for non-conventional multi-hole pressure probes
… algorithms for non-conventional multi-hole pressure probes. The algorithms that have been developed for conventional 5- and 7-hole probes are not optimal for probes with port arrangements (on the probe tip) that are non-conventional. Conventional algorithms utilize the axisymmetry of the …
-
HEIGHT ESTIMATION AND CONTROL OF A ROTORCRAFT IN GROUND EFFECT USING MULTIPLE PRESSURE PROBES
This thesis describes a dynamic height estimator and controller for rotorcraft landing and hovering in ground effect based on flowfield sensing and modeling. The rotor downwash in ground effect is represented using a ring-source potential flow model selected for real-time use. Experimental …
-
Measurement Drift in 3-Hole Yaw Pressure Probes From 5 Micron Sand Fouling at 1050° C
3-hole pressure probes are capable of accurately measuring flow angles in the yaw plane. These probes can be utilized inside a jet engine hot section for diagnostics and flow characterization. Sand and other particulate pose a significant risk to hot section components and measurement devices in …
-
Water permeability of plant cells measured by pressure probes: effects of light and turgor, and the role of unstirred layers
… single cells, during measurements with the cell pressure probe (CPP) and (ii) on the use of the latter technique to investigate changes in water permeability of leaf cells in response to light. Internodes of the giant green alga Chara corallina and parenchyma cells of corn leaves were used in the …
-
Design, Calibration, and Application of a Sensor for Measuring Time Dependent Angle of Attack of Helicopter Blades
Various pressure probes were designed and tested which could be attached to helicopter blades when a helicopter is in flight. The pressure probes consisted of spherical heads which were held in place by cylindrical shanks. Built inside the heads were transducers to measure the pressure differential …
-
High Pressure Nuclear Magnetic Resonance Studies of Homogeneous Catalysts
… from $-40\sp\circ$C to $100\sp\circ$C and pressures up to 4000 psi is described. Its significant features are a built-in stirring mechanism to mix the sample under study with reactive gases, and resolution and sensitivity comparable to that obtained in ambient-pressure probes without sample …
-
The Effects of Freestream Turbulence on Serpentine Diffuser Distortion Patterns
… used to measure inlet turbulence, while static pressure probes located axially along the upper and lower surface of the model diffuser and total pressure probes located across the aerodynamic interface plane (AIP) were used to measure the distortion patterns of the flow passing through the …
-
Experimental study on the hydrodynamics in the riser of a circulating fluidized bed.
… In this work, a pair of dual-stem differential pressure probes have been developed for the measurements of the differential pressure fluctuation in the axial direction of a dense, vertical gas-solid two phase pipe flow. The application of the statistical analysis to the differential pressure …
-
The effects of turbulence on the measurements of five-hole probes
… of turbulence on the measurements of five-hole pressure probes (5HP) and to develop a model capable of predicting the response of a 5HP to turbulence. The five-hole pressure probe is a commonly used device in experimental fluid dynamics and aerodynamics. By measuring the pressure at the five …
-
Computational Characterization of Unsteady Three-dimensional Corner Effects in a Scramjet Isolator Flow Path for Early Unstart Detection
… the flow downstream of the isolator to simulate pressure rises associated with combustion-induced effects that can lead to upstream shock propagation, premature mode transition, and potential unstart. This enables the experimental facility to fine-tune the onset and position of the pre-combustion …
-
Testing and analysis of a transonic axial compressor
… Rig and instrumented with fixed temperature and pressure probes. A new PC-based data acquisition system was commissioned and programmed for stage performance measurements. These were obtained at 50, 60, 65, 70, and 80% of the design speed before failure of the spinner retaining bolt led to the …
-
SEPARATION POINTS ON A CYLINDER IN SINUSOIDALLY OSCILLATING FLOW
… values of the governing parameters. Differential-pressure probes (sublayer fences), flush-mount hot film sensors, and flow visualization were used to determine the instantaneous positions of the separation points. Subsequently, small smooth cylinders, oscillating in water otherwise at rest, and …
-
Study of cylindrical imploding detonations
… a focusing effect by which the temperature, the pressure and the front velocity are drastically increased as the front reaches the center of implosion. We have verified this effect in cylindrical imploding detonations by measuring the front velocity, the pressure and the temperature. The velocity …
-
Base Region Topology of Turbulent Wake around Finite Wall-Mounted Cylinder with Application of Low Order Flow Representation
… can be reconstructed with correlated surface pressure sensors to have a closer look at the mechanisms leading to dipole and quadrupole wakes. It was observed that optimum choice of sensor locations needs analytical considerations to improve the ability of pressure probes in capturing the …
-
MEASURING INTERNAL FLOW PATTERNS OF A TRANSONIC COMPRESSOR
… velocimetry, laser Doppler velocimetry, Kulite pressure probes, and temperature probes, data was gathered within the passage for the first time. The probe data allowed the analysis of flow behavior within the passage. This data was used to provide information on the mass flow recirculation rates …
-
Force and Wake Characteristics of Road Vehicles and Simple Bluff Bodies Near to Ground with an Examination of the Loads on Road Vehicles in Proximity to Others
… are determined. Hot wire anemometer and pressure probes are used to derive velocity profiles, turbulence intensities, decay rates and periodic effects in the wake. Two distinct types of vortex wake are obtained, depending on whether the lift is generated by the influence of camber or …
-
Digitization of Wind Tunnel Experiments: An AI-Based Approach to Wind Field Reconstruction and Visualization
… fields. Furthermore, measurements from porous pressure probes validated the deep learning model’s predictions of velocity profiles and turbulence intensity under low wind speed conditions. Experimental results demonstrate that this approach successfully reconstructs high-resolution, time-series …
-
Friction Factor Measurement, Analysis, and Modeling for Flat-Plates with 12.15 mm Diameter Hole-Pattern, Tested with Air at Different Clearances, Inlet Pressures, and Pressure Ratios
… of 0.254, 0.381, and 0.635 mm and three inlet pressures of 56, 70, and 84 bar with all possible pressure ratios at each configuration. The friction factor data are presented for all tested configurations, with description of the test rig and theory behind the calculations. The effect of hole …
-
Investigation of the Effects of an Upstream Cavity on the Secondary Flow in Transonic Turbine Blade Passages with Endwall Contouring
… understanding of secondary flows in modern high-pressure (HP) turbine blade passages. More specifically, it aims to improve the understanding of vortical structures near the endwall with respect to the presence of an upstream cavity that approximates the gap present in actual engines between the …
Page 1 of 2