Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 13 of 13 for “"Process control agent"”.
-
Synthesis and characterization of Al-Nanodiamond composite powders by high-energy ball milling
… component powders. Stearic acid was used as a process control agent to minimize agglomeration of the powders upon milling. A uniform distribution of the ND reinforcement was successfully obtained after milling the powders for a period of ten hours with a ball-to-powder ratio of 30:1 in a SPEX …
-
Synthesis and Characterization of Aluminum-Carbon Nanotube Composite by Cryogenic Milling
… was conducted in preparation for bulk powder processing to be used in cold spray. Al-CNT metal matrix composite powders with 5 wt.% and 10 wt.% CNT were synthesized by cryogenic milling of the blended component powders. Stearic acid was used as a process control agent to minimize agglomeration …
-
Fabrication and characterisation of Pt-Co electrocatalysts for oxygen reduction reaction in polymer electrolyte membrane fuel cells
… ball to powder ratio, milling time and amount of process control agent were fabricated to optimize ball-milling conditions. Process control agents used were carbon and stearic acid. Ball to powder ratios of 39:1 or 78:1 were used and milling time was varied from 10 minutes to 90 hours. The …
-
Nano-engineering of composite material via reactive mechanical alloying/milling (RMA/M)
… This Reactive Mechanical Alloying/Milling process uses in situ reactions between the metallic powders and elements from a process control agent and/or a gaseous environment to assemble a dispersed small hard particle phase within the matrix by a bottom-up approach. In the current research …
-
Experimental and Computational Studies of Cobalt-Containing High-Entropy Alloys for Wear-Resistance Application
… by SPS. Carbon introduced from the toluene process control agent (PCA) promoted carbide formation in the milled powders. Characterization by XRD, DSC, and SEM/EDS revealed that the SPS-consolidated CoCrFeNiWx and CoCrFeNiMox alloys possess homogeneous, ultrafine microstructures consisting of …
-
Study on hydrogen storage performance of as-milled Ti-V-Cr-Fe-Mn high entropy alloys
… systematically investigates the effects of processing parameters (including milling time, ball-to-powder ratio, rotation speed, and process control agent (PCA) addition), alloy composition, and heat treatment on the phase structure, thermodynamic stability, and hydrogen storage performance …
-
Calcium oxide-based sorbents for CO2 capture at high temperature
… lies in improved and cost-effective capture processes/materials. Pre-combustion CO2 capture from coal-fired power plants is of particular interest in integrated gasification combined cycle (IGCC) design. High concentrations of CO2 and elevated operating pressures/temperatures reduce the …
-
Aluminum-silicon carbide composite coatings by plasma spraying
… 37 um in the Al-50vol%SiC composite coatings. A Process Control Agent (PCA) was used to modify the morphology of the powders during the process of mechanical alloying. Mechanical alloying produced composite powders in a size range between 40 and 120 u.m with the SiC phase uniformly dispersed …
-
Production of strengthened copper materials by Mechanical Milling-Mechanical Alloying and Spark Plasma Sintering
… induced by severe plastic deformation during the process. Then an enhanced hardening has been obtained by dispersion of a second harder phase in the copper matrix by mechanical alloying (MA), leading to the production of metal matrix composites (MMC). In this PhD thesis strain hardened and …
-
Synthesis and characterization of mechanically alloyed aluminum-based compounds as high energy density materials
… measurements were performed to identify the processes affecting ignition for the prepared metastable powders. Al-Ti alloys were prepared with compositions ranging from Al_{0.95}Ti_{0.05} to Al_{0.75}Ti_{0.25}. Mechanically alloyed powders comprised solid solution of Ti and Al. Upon their …
-
Preparation and characterization of reactive composites combining boron with mixed oxides
Thirteen liquids have been explored as Process Control Agents (PCAs) for high-energy mechanical milling of two metal oxide powders, CuO and Bi_2O_3, with the practical purpose to reduce the sizes of powder particles and refine their crystal structure. Multiple liquid properties have been considered …
-
The role of microstructure on the combustion and impact behavior of mechanically activated nickel/aluminum reactive composites
… (MA) Ni/Al reactive composite. A two-step process is adopted that includes dry milling followed by wet milling using hexanes as a process control agent. The microstructure of the resulting powder contains layered Ni and Al laminates that have micron to nano-scale dimensions depending upon …
-
Cryomilling and Spark Plasma Sintering of 2024 Aluminium Alloy
… cryogenic milling does not require use of process control agent (PCA) that can contaminate the powder with carbon and oxygen. A very important factor to preserve the nanostructure of a material is its thermal stability that depends on the balance between driving and resisting forces. It is …