Global ETD Search

Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.

Results

Showing 1 to 20 of 177 for “"Process temperature"”.

  1. A Study on the Effect of Bond Stress and Process Temperature on Palladium Coated Silver Wire Bonds on Aluminum Metallization

    … In this thesis, the effect of the two specific process parameters “bond stress” and “process temperature” on the ball bonds made with the new candidate wire are investigated. Using 20 μm diameter wire and various level-combinations of these process parameter, ball bonds are produced according to …

    waterloo Repository record for A Study on the Effect of Bond Stress and Process Temperature on Palladium Coated Silver Wire Bonds on Aluminum Metallization (opens in a new tab)

  2. Hydrogen Passivation of Polycrystalline Silicon Thin Film Solar Cells on Glass

    … solar cells is focused on finding impact of process parameters on thicker cells (3, 4, and 5 um) than baseline 2 um cell. It is discovered that higher process temperature improves open-circuit voltage most and the impact increases as cell is getting thicker. Process time and plasma power does …

    unsw Repository record for Hydrogen Passivation of Polycrystalline Silicon Thin Film Solar Cells on Glass (opens in a new tab)

  3. Lignin Yield Maximization of Lignocellulosic Biomass by Taguchi Robust Product Design using Organosolv Fractionation

    … a byproduct of the organosolv pretreatment process using lignocellulosic biomass from switchgrass (<em>Panicum virgatum</em>) and tulip poplar (<em>Liriodendron tulipifera</em>) is currently being explored for its potential use in the production of value-added chemicals and biobased …

    ut-knoxville Repository record for Lignin Yield Maximization of Lignocellulosic Biomass by Taguchi Robust Product Design using Organosolv Fractionation (opens in a new tab)

  4. Fabrication of Capacitive Micromachined Ultrasonic Transducers based on Adhesive Wafer Bonding

    … trade-offs and limitations associated with process complexity, structural parameter optimization and wafer materials selection. For example, surface micromachining approaches can suffer from complicated fabrication processes. In addition, structural parameters cannot be fully optimized due …

    waterloo Repository record for Fabrication of Capacitive Micromachined Ultrasonic Transducers based on Adhesive Wafer Bonding (opens in a new tab)

  5. Transient Thermal Modeling of Bioprocessing Equipment

    Bioprocessing is leveraging cells to produce high value, lifesaving products. Precise environmental control is needed to maintain integrity of the bioprocessing production process. Temperature control requires both appropriate equipment choice and correct control parameter selection. To aid in the …

    utahstate Repository record for Transient Thermal Modeling of Bioprocessing Equipment (opens in a new tab)

  6. Selektyviai sužadintų krūvininkų dinamika kolegiruotame ir nekolegiruotame scintiliatoriuje GAGG:Ce /

    … electron traps and their role in scintillation process, temperature dependent photoluminescence spectroscopy was carried out. Three different sets of measurements for both samples were made by exciting 5d1, 5d2 levels of Ce3+ and by exciting electrons from valence band of GAGG to the shallow …

    vilnius Repository record for Selektyviai sužadintų krūvininkų dinamika kolegiruotame ir nekolegiruotame scintiliatoriuje GAGG:Ce / (opens in a new tab)

  7. Investigation of processing and structural properties of cathodic arc deposited carbon-based coatings for bipolar plates

    … rate and elevated ionization enabling rapid processing and precise tuning of coating properties. This capability allows for the development of coatings with enhanced performance characteristics important for metallic bipolar plates. First, metal ion sputtering (MIS) for surface preparation is …

    qucosa-diss

  8. TRANSIENT THERMAL FINITE ELEMENT SIMULATION FOR PROCESS MODELING IN WIRE ARC ADDITIVE MANUFACTURING

    … thermal behavior for a given voltage, initial temperature, and travel speed during the process to predict process temperature. The outcomes of this thesis aim to significantly decrease material waste and repetitive experiments and accelerate production process design for WAAM. Furthermore, this …

    mtu Repository record for TRANSIENT THERMAL FINITE ELEMENT SIMULATION FOR PROCESS MODELING IN WIRE ARC ADDITIVE MANUFACTURING (opens in a new tab)

  9. Analytical Modeling and Simulation of Capacitive Micromachined Ultrasonic Transducer

    … This thesis also lays out the detail fabrication process flow of cMUTs. They are promised to be fabricated using mature of semiconductor processes which include photolithography, metal deposition and selective etching. In this thesis, in order to define the cMUT’s membrane, we will use direct …

    texas-state Repository record for Analytical Modeling and Simulation of Capacitive Micromachined Ultrasonic Transducer (opens in a new tab)

  10. Sustainable vegetable greenhouse production through bio-conversion of greenhouse solid wastes and re-utilization

    … wastes could reach the requirement for Process to Reduce Further Pathogens, PFRP (55 OC for 3 days). Ammonia emission might be a problem but it could be reduced by using air-recirculation or removed by a biofilter with compost as medium. Recirculation cooling control was found to be a …

    ubc Repository record for Sustainable vegetable greenhouse production through bio-conversion of greenhouse solid wastes and re-utilization (opens in a new tab) Download PDF for Sustainable vegetable greenhouse production through bio-conversion of greenhouse solid wastes and re-utilization (opens in a new tab)

  11. Efficient Regeneration Of Chemical Solvents For Carbon Dioxide Capture By Polymeric Membrane Contactors

    … aqueous MEA solution by the thermal swing process. The stripped CO2 gas was swept by mass flow controlled N2 reference gas and was measured by a non-dispersive infrared CO2 analyzer and gas chromatography. Substantial CO2 permeation flux through the membrane together with superior …

    nodak Repository record for Efficient Regeneration Of Chemical Solvents For Carbon Dioxide Capture By Polymeric Membrane Contactors (opens in a new tab)

  12. Predictive iterative learning control with data-driven model for near-optimal laser power in selective laser sintering

    … machines today due to a lack of sufficient process control. In order to improve process control, a Predictive Iterative Learning Control (PILC) controller is introduced that minimizes the deviation of the post-sintering temperature profile of a newly scanned part from a desired temperature. …

    texas Repository record for Predictive iterative learning control with data-driven model for near-optimal laser power in selective laser sintering (opens in a new tab)

  13. Investigation on the forgeability of magnesium alloys

    … and study the mechanism behind the forging process. Temperature is one of the vital aspects to be reviewed in this investigation, as these alloys exhibit poor deformation at low temperature. The stress-strain relation, strength coefficient and strain-hardening effect are also studied. …

    nus Repository record for Investigation on the forgeability of magnesium alloys (opens in a new tab) Download file for Investigation on the forgeability of magnesium alloys (opens in a new tab)

  14. Design of self-tuning frequency synthesizer

    … that is able to self-tune when there is a process, temperature and voltage variation. This allows the designers to design a low gain frequency synthesizer system, which produces a low phase noise without process variation constraint. The simulation results and the experimental results are …

    nus Repository record for Design of self-tuning frequency synthesizer (opens in a new tab) Download file for Design of self-tuning frequency synthesizer (opens in a new tab)

  15. Texturization processes of monocrystalline silicon with Na2CO3/NaHCO3 solutions for solar cells

    A novel Na2CO3/NaHCO3 texturization process for the surface structuring of the monocrystalline silicon substrate, aimed to improve the silicon optical characteristics to be used in solar cells, has been proposed in this thesis. The proposed process consists in the wet chemical anisotropic …

    ull Repository record for Texturization processes of monocrystalline silicon with Na2CO3/NaHCO3 solutions for solar cells (opens in a new tab)

  16. An investigation of the effects of secondary processing on the fracture properties of a SiCp-6XXX Al composite

    … the impact of post- fabrication deformation processing and heat treatment on the fracture properties of a 17.5 vol. % SiCsubp reinforced Al 6092 matrix composite is investigated. Process temperature, total strain and strain rate during extrusion were varied in order to explore the feasibility …

    nps Repository record for An investigation of the effects of secondary processing on the fracture properties of a SiCp-6XXX Al composite (opens in a new tab)

  17. GE-BASED HIGH MOBILITY CHANNEL TRANSISTORS FOR LOW POWER LOGIC AND BACK-END-OF-LINE COMPATIBLE 3D INTEGRATED CIRCUITS

    … 3D monolithic integration as well due to its low process temperature. In this thesis, we demonstrate a heterogeneous integration between Ge pFET and IGZO nFET for high performance BEOL-compatible CMOS circuit, which can be a key enabler in future 3D monolithic integrated systems.

    nus Repository record for GE-BASED HIGH MOBILITY CHANNEL TRANSISTORS FOR LOW POWER LOGIC AND BACK-END-OF-LINE COMPATIBLE 3D INTEGRATED CIRCUITS (opens in a new tab) Download file for GE-BASED HIGH MOBILITY CHANNEL TRANSISTORS FOR LOW POWER LOGIC AND BACK-END-OF-LINE COMPATIBLE 3D INTEGRATED CIRCUITS (opens in a new tab)

  18. AMORPHOUS INDIUM-GALLIUM-ZINC-OXIDE-BASED TRANSISTORS FOR EMERGING NON-VOLATILE MEMORY AND NEUROMORPHIC COMPUTING APPLICATIONS

    … attention due to the back-end-of-line compatible process temperature and excellent electrical characteristics for 3D integration. This thesis is devoted to realizing emerging non-volatile memories based on the a-IGZO channel, targeting high-density storage, neuromorphic in-memory computing, and …

    nus Repository record for AMORPHOUS INDIUM-GALLIUM-ZINC-OXIDE-BASED TRANSISTORS FOR EMERGING NON-VOLATILE MEMORY AND NEUROMORPHIC COMPUTING APPLICATIONS (opens in a new tab) Download file for AMORPHOUS INDIUM-GALLIUM-ZINC-OXIDE-BASED TRANSISTORS FOR EMERGING NON-VOLATILE MEMORY AND NEUROMORPHIC COMPUTING APPLICATIONS (opens in a new tab)

  19. Studies of ReCrete: A polyurethane foam

    … This study investigates the effect of mold temperature and mold size on the average density and some of the resulting mechanical and thermal properties for a polyurethane foam system molded in aluminum cylinders and boxes. Resulting properties are also compared to more uniform foam samples …

    unlv Repository record for Studies of ReCrete: A polyurethane foam (opens in a new tab) Download PDF for Studies of ReCrete: A polyurethane foam (opens in a new tab)

  20. Power and Area Efficient Sub-threshold 6T SRAM with Horizontal Local Bit-Lines and Bit-Interleaving

    SRAM in the typical microprocessor consumes a substantial amount of on-chip area and significantly contributes to static power dissipation. This study presents a new SRAM architecture with minimum area that utilizes a modified 6T SRAM cell for sub- and near-threshold operation in ultra-low power …

    carleton Repository record for Power and Area Efficient Sub-threshold 6T SRAM with Horizontal Local Bit-Lines and Bit-Interleaving (opens in a new tab)

Page 1 of 9