Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 151 for “"Punching Shear"”.
-
Punching Shear of Flat Slabs
Užití lokálně podepřených desek ve výstavbě je v nynější době rozšířeno v mnoha zemích díky svým ekonomickým a funkčním výhodám. Přes svůj jednoduchý vzhled, je chování lokálně podepřených desek v ohybu a smyku značně komplexní. Problematika protlačení tudíž patří z hlediska návrhu betonových …
-
Punching shear strength of reinforced concrete slab.
This thesis presents the results of punching shear tests performed on a 2 x 2 bay continuous slab with/and without supplementary supports. On the basis of these tests, the code method of calculating the ultimate strength of interior, edge and corner column connections of flat slab were …
-
Characterization of Punching Shear Capacity of Thin Uhpc Plates
… and contained no reinforcing steel to resist shear. The lack of steel reinforcement allowed for the possibility of a punching shear failure to occur from the application of a point load such as a wheel tire patch load. The model and optimized section served as the foundation for this research, …
-
Punching shear strength of continuous post-tensioned concrete flat plate.
… 44 MPa. The load was applied monotonically until punching shear occurred at an edge column on the side parallel to banded tendons. The failed column was shored and the slab reloaded until punching shear occurred at the interior column. The lack of supplementary bonded reinforcing steel in regions …
-
Punching shear strength of steel fibre reinforced lightweight concrete slabs.
… the problems in slab-column connections is the punching shear failure at over loads. Such failures are sudden and catastrophic, and are undesirable since they do not allow an overall yield mechanism to develop. Fibre reinforcement restrains cracking, and increases the tensile strength of …
-
Punching shear of reinforced concrete flat plates : behavior and design considerations
… expanding the current knowledge regarding the punching shear behavior of RC flat plates by investigating the response of slab-column connections under highly-controlled two-way shear loading conditions. The influence of through-thickness shear reinforcement, longitudinal reinforcement ratio, …
-
Punching shear behaviour of FRP-reinforced concrete interior slab-column connections
… strength, type of the reinforcement, moment-to-shear ratio and the spacing between the shear stud reinforcement. Test results revealed that increasing the GFRP reinforcement ratio or the concrete strength increased the connection capacity. Moreover, compared to the control steel-RC specimen, the …
-
Punching shear strength of edge column connections of rectangular flat plates
… continuous flat plate structures, under combined shear and moment transfer, can be susceptible to failure by punching shear. A 2 bay by 2 bay, rectangular flat plate, panel aspect ratio 2:1, was fabricated and loaded to failure under a simulated uniformly distributed load. The edge and corner …
-
Effect of Unbalanced Moment on Punching Shear Strength of Slab-Column Joints
… the distribution of unbalanced moments between shear and flexure stresses were introduced in the 1970s based on limited research. Research on the topic of slab-column connections subjected to eccentric loading has deviated away from the linear shear distribution assumptions of Canada, the U.S., …
-
Punching Shear Retrofit of Concrete Slab-Column Connections with GFRP Shear Bolts
… structures might need to be strengthened for punching shear. Using steel shear bolts to strengthen connections for punching shear is a new technique used for retrofit that was developed at the University of Waterloo. If the retrofitted part of the structure is exposed to the atmosphere, or to …
-
Punching Shear Strength of Unbonded Prestressed Flat Slabs at Edge Column Connections
… an experimental and theoretical study of the punching shear strength of unbonded prestressed flat slabs at edge column junction. Six tests were conducted under monotonic loading and two under cyclic loading. The models were approximately 1000 x 1000 x 130 mm and prestressed in two directions …
-
Punching shear of concrete flat slabs reinforced with fibre reinforced polymer bars
… polymer (GFRP) and steel bar materials for punching shear behaviour. Six full-scale two-way slab specimens were constructed and tested under concentric load up to failure. One of the main objectives is to study the effect of reinforcement spacing with the same reinforcement ratio on the …
-
Punching shear failure of foundations on strong sand overlying deep weak deposit
… failure mechanisms in conjunction with the punching shear failure. Accordingly, assumptions were used to simplify the evaluation of the level of mobilization of the shear strength on the punching column. This is mainly due to the complexity of modeling the earth pressure distribution on the …
-
Nonlinear Finite Element Analysis of Punching Shear of Reinforced Concrete Slab-Column Connections
… due to the extensive cost and time that a punching shear test requires. Thus, there is a need for verification of the actual code provisions and this can be done in part by using finite element (FE) simulations. The finite element analyses (FEA) can supplement the existing testing …
-
Flexure And Punching Shear Behavior Of Uhpc Elements Post-Tensioned With Unbonded Tendons
ABSTRACTFLEXURE AND PUNCHING SHEAR BEHAVIOR OF UHPC ELEMENTS POST-TENSIONED WITH UNBONDED TENDONS by Mehmet Dogu August 2021 Advisor: Dr. Fatmir Menkulasi Major: Civil and Environmental Engineering (Structural Engineering) Degree: Doctor of Philosophy Procedures for predicting the flexural …
Page 1 of 8