Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 231 for “"Reduction factor"”.
-
Re-Evaluation of the CSA S304 Concrete Masonry Flexural Compressive Strength Reduction Factor
… the inclusion and maintenance of the χ-factor in Clauses 10.2.6 and 11.2.1.6 of the CSA S304 Design of Masonry Structures to reduce the flexural compressive strength when the internal compressive stress acts perpendicular to the head joint. The results from recent research conducted …
-
The Structure of The Carbon Dioxide Reduction Factor, a Novel Carbon Carrier in Methanobacterium Thermoautotrophicum
Made available in DSpace on 2014-12-16T06:12:51Z (GMT). No. of bitstreams: 1 8409984.pdf: 3721066 bytes, checksum: eb26f8d46b1910adac3f827266c16bb5 (MD5) Previous issue date: 1983
-
Determination of stiffness reduction factor for U-shaped reinforced concrete shear walls under bi-axial loading
… study was devoted to determining a stiffness reduction index that can monitor current damage state of the wall system as a whole, and apply the unified damage index to decrease stiffness and strength on other directions. This study proposes an analytical framework at microscopic length scale …
-
Evaluation of Strength Reduction Factor for Concentrically Braced Frames Based on Nonlinear Single Degree-of-Freedom Systems
Strength Reduction Factor (R-Factor), often referred to as Response Modification Factor, is commonly used in the design of lateral force resisting systems under seismic loading. R-Factors allow for a reduction in design base shear demands, leading to more economical designs. The reduction of …
-
Uplift loaded standing seam roof systems
… It was found that by normalizing the data, a reduction factor could be established for each test set configuration. This reduction factor applies to both the base test and confirming multi-span test in each test set. Three analytical models were applied to predict the failure of the purlin. It …
-
Hysteresis rules of perforated low-rise reinforced concrete shear walls and seismic design parameters assessment of buildings
… study of design parameters includes ductility reduction factor, force reduction factor, overstrength factor, and ratio of displacement amplification to force reduction factor. Results are recommended for future building code development"--Abstract, page iii.
-
Modeling of Microstructures and Stiffness of Injection Molded Long Glass Fiber Reinforced Thermoplastics
… In various fiber orientation models, a strain reduction factor is usually applied to match the slower fiber orientation evolution observed experimentally. In this research, a variable strain reduction factor is determined locally by the corresponding local flow-type and used in fiber …
-
Effect of Inclined Loading on Passive Force-Deflection Curves and Skew Adjustment Factors
… Frederickson 2015) led to the proposal of a reduction curve used to determine a passive force skew reduction factor depending on abutment skew angle (Shamsabadi and Rollins 2014). In all previous tests, a uniform longitudinal load has been applied to the simulated bridge abutment. During …
-
Flange Buckling Behavior of Stainless Steel Girders with Trapezoidally Corrugated Webs - A parametric numerical study
… the elastic buck ling coefficient and required reduction factor. The analyses are performed in theanalysis software ABAQUS. The results of the parametric numerical studies arecompared to the existing models for carbon steel girders suggested by Eurocode 3(EN1993-1-5), the DASt Richtlinie 015 and …
-
Wave loads and motions of long structures in directional seas
… as a directionally averaged, frequency dependent reduction factor for the wave loads and a response ratio for the body motions. Numerical results are presented for the force reduction factor and response ratio of a long floating box subject to a directional wave spectrum with a cosine power type …
-
Developing freeway merging calibration techniques for analysis of ramp metering In Georgia through VISSIM simulation
… performed to determine the effects of the safety reduction factor and the maximum deceleration for cooperative braking parameter on the simulated merging behavior. Results indicated that having both the advanced merging and cooperative lane change setting active produced the best results and that …
-
Load-Deformation Behavior of Tension-Only X-Brace Roof Truss Diaphragms
… methods. However, the diaphragm design force reduction factor has not yet been determined for tension-only roof truss diaphragms, a common system used in metal buildings. In this study, experimental tests of two cantilevered diaphragm subassembly specimens with tension-only rod bracing were …
-
Sensitivity analysis of the response characteristics of pattern search techniques applied to exponentially smoothed forecasting models
… size, 3) pattern search step size, 4) step size reduction factor, 5) exponential smoothing constants (A, B and C). As the values of these input parameters were changed during the course of the analysis the resultant changes in certain criterion variables of the system were noted. These variables …
-
Αντισεισμικός σχεδιασμός επίπεδων μεταλλικών διασυνδεδεμένων πλαισίων με χρήση τριών νέων μεθόδων
… while the second makes use of modal strength reduction factors resulting from the corresponding modal damping ratios. The basic idea of first two design method is related to the creation of an equivalent linear MDOF structure that is able to respond in a similar way to the corresponding …
-
Assessment of seismic force modification factors for conventional construction reinforced concrete shear wall structures in Canada using the performance-based unified procedure
… (NBC). NBC specifies seismic force modification factors, such as ductility-related factors (Rd) and overstrength-related factors (Ro), with values of 1.5 and 1.3 for conventional construction concrete shear walls, respectively. Values for these parameters are largely based on engineering judgment …
-
The engineering of construction specifications for externally bonded FRP composites
… as through fibers, it is recommended to use a reduction factor for strength and no reduction factor for stiffness to account for fiber misalignment. Findings from concrete beams strengthened with misaligned CFRP laminates verified these recommendations. The fourth and fifth papers investigate …
-
Calculation of stiffness in slender reinforced columns and arches in concrete bridges: A parametric study on stiffness calculation for isolated columns according to Eurocode
… by at least 29 %. The analysis shows that a reduction factor of approximately 0.45 can be applied to single, isolated columns, whereas columns with adjacent structural elements require a uniform reduction factor of 0.85 for all cases considered. By incorporating these factors into …
-
Improved Prediction of Glass Fiber Orientation in Basic Injection Molding Geometries
… strain closure model) and non-objective (strain reduction factor model) orientation model. The predicted values of the strain reduction factor model showed reasonable agreement with experimentally obtained values of orientation throughout the three-dimensional cavity when using orientation …
-
Reliability-based durability assessment of GFRP bars for reinforced concrete
… of environmental and flexural strength reduction factors, which have minimal experimental validation. Our goal in this research is the development of a Monte Carlo simulation to assess the durability of glass fiber reinforced polymer (GFRP) reinforced concrete designed for flexure. The …
Page 1 of 12