Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 60 for “"Reference plane"”.
-
The determination of an extra-skeletal reference line and its reliability
… was undertaken to determine an extra-skeletal reference plane and its reliability. The results of this study revealed that it seems possible for an orthodontist to establish an extra-skeletal reference plane, if a specially designed analyzer is used. It has been shown that by using this devise …
-
Characterization of diffusers and light-emitting diodes using radiometric measurements and mathematical modeling
… the position of the apparent detector receiving plane (reference plane). In this thesis, the reference planes of four spectroradiometer diffusers have been investigated and found to be located, in most cases, inside the diffuser. The reference plane shift should be taken into account in the …
-
Geometry-Aware Modeling of Rough-Wall Turbulence Using Reynolds-Averaged Navier-Stokes (RANS) Frameworks
… sublayer. The second study introduces a reference-plane framework that explicitly partitions the flow into a geometry-dominated near-wall inner region and an outer region governed by the k-ε model. The reference plane is placed at the equivalent sand-grain roughness height, with velocity …
-
Facial Planes as Landmarks for Diagnosis and Treatment Planning
… elements of craniofacial morphology to selected reference planes. Ideally, a valid reference plane should have good intra-individual reproducibility, low inter-individual variability, and good reliability. The aim of this study was to determine 1.) the reliability and reproducibility of FALL and …
-
Calibration of structured light system using unidirectional fringe patterns
… to calibrate the camera-projector system using a reference plane. The object geometry was reconstructed by comparing the phase difference between the object and the reference plane. However, the chosen reference plane needs to simultaneously possess a high planarity and a good optical property, …
-
Effects of Wall Roughness on Adverse Pressure Gradient Boundary Layers
… velocity and momentum thickness at the reference plane) is 2300. A sand-grain roughness model was implemented and spatial resolution requirements were determined. Two roughness heights were used and a fully-rough flow condition is achieved at the reference plane with roughness Reynolds …
-
General parallel-leg mechanism : position analysis
… imposed are the leg bases are all on the same reference plane and the tool orientation is normal to the mobile upper plate. This is done for a parallel leg mechanism having any number of legs. The variable chosen is the first leg's vertex position on the upper plate. The state space is the …
-
A linked-plane obstacle-set algorithm for modeling broad muscle paths : application to the deltoid muscle.
… Each band is constrained to lie in its own plane and wrap around its own sphere. Each band plane forms a given angle with respect to the adjacent band plane, with the first band plane forming an optimized angle with respect to a fixed reference plane. The optimization seeks to minimize the …
-
DEVELOPMENT OF PHASE RETRIEVAL TECHNIQUES FOR DIGITAL FRINGE PROJECTION PROFILOMETRY
… extra fringe patterns. In the third work, novel reference-plane-based methods are proposed for high-quality absolute phase retrieval with a minimum number of fringe patterns. Finally, an effective assessment method is proposed to quantify the phase retrieval quality obtained by the FPP …
-
A proposed method for evaluation of morphological changes in the condyle and glenoid fossa by cone beam computed tomography
… them in magnitude (mm) and direction (°) on a reference plane after superimposing the cone beams three-dimensionally on the inferior alveolar nerve canal and the lower contour of the third molar tooth germ. Two sets of measurements were compared for reliability and each measurement showed …
-
Cephalometric Objectives for the Maxillary Central Incisor
… and stepwise regressions. The Frankfort plane was found to be the most reliable reference plane when measuring the inclination of the maxillary central incisor. The maxillary central incisor inclination was found to be dependent upon the lower incisor position and inclination, chin …
-
ΣΧΕΔΙΑΣΗ ΚΑΙ ΑΝΑΠΤΥΞΗ ΕΝΕΡΓΩΝ ΔΙΑΤΑΞΕΩΝ ΧΙΛΙΟΣΤΟΜΕΤΡΙΚΩΝ ΣΥΧΝΟΤΗΤΩΝ ΜΕ ΣΥΝΑΦΕΙΑ ΦΑΣΗΣ
… COMPLEX IMPEDANCE OF THE CAVITY IS COMPUTED WITH REFERENCE PLANE THE POSITION OF THE GUNN DIODE WHICH WILL PRODUCETHE NEGATIVE RESISTANCE IN ORDER TO MAINTAIN THE MMW OSCILLATIONS. THE METHODUSED TO COMPUTE THE COMPLEX IMPEDANCE IS GALERKIN ONE WHICH LEADS TO PACKLINGTON TYPE INTEGRAL EQUATIONS. …
-
Clinical Photographic Analysis of Dentofacial Midline Asymmetries
… problems in locating a reliable median sagittal reference plane, and because of the complexity and time involved in analysis. For these reasons, the clinician has generally resorted to direct visual observation in diagnosing midline discrepancies. A quick, precise, chairside method of dentofacial …
-
Selective Subtraction: An Extension of Background Subtraction
… standard background subtraction, and show that a reference plane in a scene viewed by two cameras can be used as the decision boundary between foreground and background. In our definition, the foreground may actually occur behind a moving object. Our novel use of projective depth as a decision …
-
Comparison of the Facial Changes According to the Treatment Modalities: Anterior Segmental Osteotomy vs. Extraction Orthodontic Treatment with Palatal TAD
… backward by 3.92mm relative to the Vertical Reference Plane(VRP), whereas in Group B, the SNA decreased by 4.26° and the A point moved backward by 5.97mm (SNA, p = 0.000; A point, p = 0.002). As a result of the analysis of dental changes, in group A, the maxillary anterior teeth had 8.92mm …
-
Propagation of delamination in layered anisotropic cylinders
… force. The axial and shear strains of the reference plane are considered negligible compared to its circumferential strain. The cylinder, after delamination, is modelled as three shell elements joined at the crack tip. A sharp, flat crack tip is assumed, and the slopes of the three shell …
-
Exploring the Sources of Variation in the SN-FH Angle and Its Components: A Comparison of Three Ethnic Groups
… both the sella-nasion and Frankfort horizontal reference planes between and within these populations. Secondarily, the study aimed to determine if the SN-FH angle correlates to facial divergence and growth tendencies observed radiographically. Materials and Methods This retrospective, …
-
Matrix algebra applied to the calculation of fifth-order aberrations in optical systems.
… produce a matrix for one surface to obtain image plane coordinates from those in the object plane, when given an initial ray direction, by multiplying in proper syquence two translation and one refraction matrices. He also constructed another objeqt to image matrix which used paraxial …
-
Three-dimensional CBCT analysis of cranial base symmetry
… a set of normative data that can be used as a reference for future studies. Material and Methods: Pre-treatment Cone Beam Computed Tomography (CBCT) films of 160 esthetic human subjects previously used by another investigator were screened for use in our current research. These DICOM files were …
Page 1 of 3