Global ETD Search

Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.

Results

Showing 1 to 18 of 18 for “"Reinforcing fiber"”.

  1. Development of polypropylene fiber as concrete reinforcing fiber

    … of this research is to produce polypropylene fibers with improved interface bonding with a concrete matrix. The Laboratory Mixing Extruder paired with the Randcastle fiberline drawing device was used for producing fiber from polypropylene (PP) chips. A target diameter of 0.5 mm fiber was …

    ubc Repository record for Development of polypropylene fiber as concrete reinforcing fiber (opens in a new tab) Download PDF for Development of polypropylene fiber as concrete reinforcing fiber (opens in a new tab)

  2. An analysis of the interfacial bond between polypropylene reinforcing fiber and cement matrices

    … the interfacial bond between polypropylene fiber and Type l Portland cement and also to investigate the improved qualities of the interfacial bond. The process chosen to improve the interfacial bond between polypropylene fiber and the cement matrix was a chemical surface treatment. The …

    iastate Repository record for An analysis of the interfacial bond between polypropylene reinforcing fiber and cement matrices (opens in a new tab)

  3. Laboratory development and tensile testing of grapite/glass/epoxy hybrid composite materials.

    … in use today consist of a single type of reinforcing fiber embedded in a matrix. There are possible advantages, however, in a system which used multiple types of reinforcing fibers. Such a material is called a "hybrid" or "mixed modulus" composite. This thesis describes the establishment …

    nps Repository record for Laboratory development and tensile testing of grapite/glass/epoxy hybrid composite materials. (opens in a new tab)

  4. Short-Term Failure Analysis of Aluminum Conducting Composite Core Transmission Lines

    … are concentrated at the interface in the carbon fiber composite region. The composite materials' compressive strength was measured, and found to be significantly lower than similar composite materials based upon the same reinforcing fiber. An excessive bending finite element model was …

    denver Repository record for Short-Term Failure Analysis of Aluminum Conducting Composite Core Transmission Lines (opens in a new tab)

  5. A characterization of the interfacial and interlaminar properties of carbon nanotube modified carbon fiber/epoxy composites

    … (IFSS) of carbon nanotube (CNT) coated carbon fibers and the interlaminar fracture toughness of woven fabric carbon fiber/epoxy composites toughened with CNT/epoxy interleave films is presented. The deposition of multiwalled carbon nanotubes (MWCNT) onto the surface of carbon fibers through …

    tamu Repository record for A characterization of the interfacial and interlaminar properties of carbon nanotube modified carbon fiber/epoxy composites (opens in a new tab)

  6. The influence of surface properties on carbon fiber/epoxy matrix interfacial adhesion

    … materials depends not only on the matrix and the reinforcing fiber, but also to a great extent on the fiber/matrix interfacial adhesion. The focus of this work was to study carbon fiber surface chemical and physical properties and their effects on fiber/matrix adhesion. Untreated, commercially …

    vt Repository record for The influence of surface properties on carbon fiber/epoxy matrix interfacial adhesion (opens in a new tab)

  7. Accounting for Paramagnetic Influence in Wetted Surface Area Studies of Particle Suspensions Using Solvent Relaxometry

    … materials sustained by the synergy between a reinforcing fiber, also known as filler, and a resin matrix. Since performance relies on interfacial interactions between the PMC components, the surface area of particle fillers is a key design consideration. Here, the characterization of Kevlar® …

    ku Repository record for Accounting for Paramagnetic Influence in Wetted Surface Area Studies of Particle Suspensions Using Solvent Relaxometry (opens in a new tab)

  8. A Study of Cellulose Based Biodegradable Foams and Sponges

    … resources. Investigations regarding use of wood fibers and other biomass as a raw material for biodegradable foams and sponges are an example of such a replacement. Foams made at least partially of biomass can be created using cellulose from wood fibers once the cellulose is converted into a …

    gatech Repository record for A Study of Cellulose Based Biodegradable Foams and Sponges (opens in a new tab)

  9. Mechanical degradation of thermal properties of flexible aerogel blankets

    … of silica aerogel particles dispersed in a reinforcing fiber matrix that turns the brittle aerogel into a durable and flexible insulating mat.;While aerogel blankets exhibit excellent thermal properties, they are still some concerns over dust mitigation when the blankets are flexed and …

    wvu Repository record for Mechanical degradation of thermal properties of flexible aerogel blankets (opens in a new tab)

  10. Adhesion and Interphase Properties of Reinforced Polymeric Composites

    … material with a wide range of applications. Fiber reinforced polymeric composites, in particular, possess impressive mechanical properties at a fraction of the weight of many other building materials. There will always, however, be a demand for producing lighter, stiffer, and stronger …

    washington Repository record for Adhesion and Interphase Properties of Reinforced Polymeric Composites (opens in a new tab)

  11. Development And Characterization Of Nanoparticlee Enhancements In Pyrolysis-derived High Temperature Composites

    … justifiable. Previous work by others with “fuzzy fiber” composites have shown that aligned carbon nanotubes (CNTs) grown on fibers can improve their thermal conductivity and wettability. To this end vertically aligned CNTs were studied for their potential use, but found to be difficult to process …

    ucf Repository record for Development And Characterization Of Nanoparticlee Enhancements In Pyrolysis-derived High Temperature Composites (opens in a new tab)

  12. A thermoplastic matrix continuous fiber reinforced composite impregnation method by direct polymer extrusion

    During component design, continuous fiber reinforced composite material systems are often chosen largely based on their structural efficiency. Their mechanical properties, such as specific strength and specific stiffness, are often cited as significant advantages over the use of other materials. …

    colostate Repository record for A thermoplastic matrix continuous fiber reinforced composite impregnation method by direct polymer extrusion (opens in a new tab)

  13. Nylon-6/Agricultural Filler Composites

    … using engineering thermoplastics and plant fibers or fillers is a technical challenge because the processing temperature of the thermoplastics is generally above the temperature of degradation of plant fibers of fillers. There have been numerous attempts for processing high melting point …

    waterloo Repository record for Nylon-6/Agricultural Filler Composites (opens in a new tab)

  14. Durability of Polymer Matrix Composites for Infrastructure: The Role of the Interphase

    As fiber reinforced polymer matrix composites find greater use in markets such as civil infrastructure and ground transportation, the expectations placed on these materials are ever increasing. The overall cost and reliability have become the drivers of these high performance materials and have led …

    vt Repository record for Durability of Polymer Matrix Composites for Infrastructure: The Role of the Interphase (opens in a new tab)

  15. 3D tisk kompozitních materiálů

    Předložená diplomová práce se zabývá studiem kompozitních materiálů a jejich zpracováním pomocí technologie 3D tisku. Experimentální část je zaměřena na výrobu zkušebních vzorků s využitím aditivní technologie Fused Deposition Modeling a Continuos Filament Fabrication. Kompozitní vzorky se …

    brno-tech Repository record for 3D tisk kompozitních materiálů (opens in a new tab)

  16. Využití 3D tisku při výrobě funkčních prototypů pro automotive

    Diplomová práce se zabývá problematikou 3D tisku kompozitních materiálů. Neustálý vývoj této technologie umožnil aplikaci výtisků nejen do výroby prototypů, ale také funkčních součástí. V teoreticko-metodologické části je definována studie kompozitních materiálů s principem výroby pomocí aditivní …

    brno-tech Repository record for Využití 3D tisku při výrobě funkčních prototypů pro automotive (opens in a new tab)

  17. Analýza mechanických vlastností kompozitních materiálů vytisknutých aditivní technologií 3D tisku

    Diplomová práce se zabývá analýzou mechanických vlastností kompozitních materiálů používaných pro 3D tisk společností Markforged. Teoretická část je zaměřena na charakteristiku kompozitních materiálů a rozbor mechanických zkoušek. Experimentální část se zabývá výrobou zkušebních vzorků pro …

    brno-tech Repository record for Analýza mechanických vlastností kompozitních materiálů vytisknutých aditivní technologií 3D tisku (opens in a new tab)

  18. Atomic Layer Deposition onto Fibers

    … deposition (ALD) can be applied to “endless” fibers. A reactor of atomic layer deposition has been designed, especially for coating depositions onto meter long bundles of fibers. Aluminum oxide (alumina), titanium oxide (titania), double layers of alumina and titania, as well as aluminium …

    qucosa-diss