Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 107 for “"Residual strain"”.
-
Time-dependent Yielding and Residual Strain Accumulation of Polymer Membranes
… and experimental investigations of the onset of residual strains of a viscoelastic polymer membrane subjected to creep loading at various temperatures. The aim of this study is to establish a model that can be employed to determine the time-to-yield given the stress and temperature history a …
-
Nondestructive residual strain measurement using high energy x-ray diffraction
… x-ray diffraction method to measure the internal strain depth-profile in materials was developed using a standard 320 kVp laboratory x-ray source. Traditional x-ray strain measurements are limited to few microns of depth due to the limited penetration of Cu Ka and Mo Ka radiation if a synchrotron …
-
The residual strain distribution around a fastener hole coldworked with a tube expander
Thesis (M.S.)--Michigan State University. Department of Metallurgy, Mechanics, and Material Science,
-
An experimental study of large compressive loads upon residual strain fields and the interaction between surface strain fields created by coldworking fastener holes
Thesis (Ph.D.) - Michigan State University. Department of Mechanical Engineering, 1980. ()--Thesis (Ph.D.) - Michigan State University. Department of Mechanical Engineering, 1980
-
An investigation into the relationship between processing, orientation and properties of low density polyethylene films
… in mechanical properties with the change in the residual strain of manufactured film. The residual strain was measured by using a shrinkage method.
-
An experimental investigation of residual stress and strain in rapidly cured fibre reinforced composites
… high specific strength and stiffness. However, residual stress is present in all fibre reinforced composites to some degree, caused by their inherent anisotropy and differential material properties between fibres and reinforcing matrix. Residual stress can cause premature failure in structures …
-
Micro-Raman measurement of strain in silicon nanowires
… such as silicon nanowires (SiNWs) may have residual mechanical stress and strain from the fabrication process, which can potentially impair their reliability as building blocks of Microelectromechanical system (MEMS). The amount of strain may be minuscule, which requires very accurate …
-
An investigation into methods of detecting dewetted zones in solid rocket propellants using holographic interferometry.
… interferometry , Techniques used were simple strain, residual strain and time-average holography. As a basis for comparison with experimental data a finite element program was used to model the test samples.
-
Mechanical behavior of individual type I collagen fibrils
… and cyclic loading/recovery experiments, and strain rate tests spanning six decades of strain rates in the range 10-3 – 102 s-1. Experiments were conducted with reconstituted type I calfskin collagen fibrils which were isolated from buffer and after drying were adhesively attached to a …
-
Understanding Residual Stress in Direct Energy Deposition: A Comprehensive Study of GRCop-42 using Finite Element Simulation and Energy Dispersive X-ray Diffraction
The development of residual stress in metal material additive manufacturing brings a significant obstacle to achieving parts with good quality. The residual stress can be destructive as the structural integrity and mechanical properties are seriously influenced during the manufacturing process. In …
-
Stress-strain and strength characteristics of clay during post-cyclic monotonic loading
… loading on the post-cyclic undrained stress-strain characteristics of a marine clay. The influence of factors, such as, cyclic stress level, number of cycles, amplitude of maximum axial strain during cyclic loading, residual pore pressure and residual strain at the conclusion of cyclic …
-
A Study of Cure Kinetics, Microstructures, and Properties of Thermoset Composites Manufactured Through Frontal Polymerization
… high energy consumption, void formation, and residual stress development, by leveraging the effects of thermal (TPED-1,1,2,2-Tetraphenyl-1,2-ethanediol) and cationic initiators to accelerate the curing process without compromising material performance.A comprehensive experimental approach was …
-
Effect of chill condition and grain refinement on the microstructure and mechanical properties of B319 aluminum alloy
… However, high thermal gradients may develop residual strain in the as-cast alloy, which may be detrimental to the life-cycle of the automotive part and thus needs to be evaluated. The results of this thesis suggest that water cooled chill provides higher thermal gradient, resulting in a finer …
-
The generation of thermal stress and strain during quenching.
… was used to calculate the thermal stress and strain generated during the quenching of an infinite plate of high hardenability steel (835M30) in water, oil and Polymer. In the present work the mathematical model was modified to include the effect of initial stress on the rate of stress …
-
Polymerization Shrinkage Strain Versus C-Factor And Placement Method For Dental Composites
… shrink during polymerization creating stress and strain around the restoration. This may produce failure at the composite-tooth interface. This leads to marginal gaps, staining, post-operative sensitivity, secondary caries, and crack development within the body of a tooth. It is critical to be …
-
The Inhomogeneous Microstructure and Deformation of Similar and Dissimilar Al-Zn Containing Mg Friction Stir Welds
… friction stir welded microstructures, textures, residual strains, and the local deformation behaviour based on strain mapping during tensile tests. Covering bead-on-plate and butt configurations, joining of similar and dissimilar materials, and a range of processing conditions, many findings of …
-
Seismic Performance of Reinforced Concrete Tall Buildings with Advanced Materials
… concrete tall buildings and reduce the residual strain upon subjecting the structure to severe earthquake shaking. The study building was evaluated for four cases of reinforcement: conventional steel Grade 60, high strength ASTM A706 Grade 80, and high strength ASTM A1035 Grade 100 and …
-
Molecular beam epitaxial growth and characterization of indium antimonide on gallium arsenide
… that of bulk InSb, indicating very little or no residual strain in the epilayers.
-
Measurement of residual stresses and solving the inverse problem to infer dislocation distributions
Residual stresses are present in the absence of external loads. All manufactured parts exhibit some degree of residual stress, which can drastically impact fatigue life. The simulation of these stresses has become exceedingly difficult as manufacturing processes have become more complex, and …
-
Epitaxial growth of dilute nitride-arsenide compound semiconductors by molecular beam epitaxy
… also favour the faceted growth mode. The residual strain in relaxed InGaAsN films is found to be higher than in InGaAs epilayers having the same lattice mismatch. In situ substrate curvature measurements were used to monitor the strain state of. the sample in real time during the growth. …
Page 1 of 6