Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 229 for “"Resistance factor"”.
-
Improving Confidence Intervals for the Resistance Factor in Load and Resistance Factor Design (LRFD)
… are generally quantified as loads and resistances. Loads are forces applied to structures which cause stress. Dead Loads Q_DL and Live Loads Q_LL are the two main types of loads considered. The resistance R is the capacity of the structure to bear the loads. For safe use of the …
-
Resistance Factor for Cold-Formed Steel Compression Members
… investigates if the LRFD strength reduction factor for cold-formed steel compression members can be increased above its current value of Ï c = 0.85, which was established by the LRFD Cold-Formed Steel Design Manual (1991) on the basis of 264 column tests. The resistance factor in the Canadian …
-
Load and resistance factor design for wood structures
… used in conjunction with the predetermined load factors and load combinations to determine resistance factors. Finally, a design format is proposed for Load and Resistance Factor Design for wood structures.
-
Building better confidence intervals for the resistance factor in LRFD
… account the load the structure will bear and the resistance of the structure against that load. Of interest in the LRFD system is the resistance factor (φ) that affects the resistance. Samples are collected to estimate φ, but the estimate (φ ̂ ) has typically been treated as a deterministic …
-
MRP2 as a Targetable Oxaliplatin Resistance Factor in Gastrointestinal Cancer
… efficacy due to the development of multidrug resistance (MDR), chemotherapy is still the treatment of choice for most of the cancer patients. One of the formidable MDR mechanisms is the up-regulation of various efflux pumps, known as the ATP binding cassette (ABC) transporters, which can …
-
Load and resistance factor design of shallow foundations for bridges
Load Factor Design (LFD), adopted by AASHTO in the mid-1970, is currently used for bridge superstructure design. However, the AASHTO specifications do not have any LFD provisions for foundations. In this study, a LFD format for the design of shallow foundations for bridges is developed. Design …
-
Conjugal fertility associated with resistance factor R in Escerichia coli
… Hirota. Conjugal fertility associated with resistance factor R in Escerichia coli. Journal of Bacteriology. 1962. 84(5), p.902-910.
-
Load and resistance factor design of cold-formed steel structural members
… structural failure by using an appropriate factor of safety selected primarily on the basis of engineering judgment and long-time experience. Recently, the concepts of risk and reliability analysis have been successfully applied to many fields of engineering. By applying the theories of …
-
Load and resistance factor design of cold-formed stainless steel structural members
… States. Recently, the probability-based load and resistance factor design (LRFD) criteria have been successfully applied to the structural design of hot-rolled steel shapes and built-up members. The AISI LRFD Specification is being developed as well for the design of structural members cold-formed …
-
Axially Loaded Drilled Shafts: LRFD Resistance Factor Calibration and Predictive Techniques for Settlement
… While the calibration of area-specific LRFD resistance factors for the strength limit state offers a potential solution to this issue, current calibration methods require that traditional or local design procedures be capable of predicting nominal capacity with a reasonable and consistent …
-
Load and resistance factor design of drilled shafts at the service limit state
… state is proposed. The procedure uses Load and Resistance Factor Design (LRFD) concepts to achieve target probabilities of failure without requiring case-specific probabilistic analyses. Proposed resistance factors are primarily dependent on four parameters: the normalized load, the coefficient …
-
Load and Resistance Factor Design (LRFD) Resistance Factors for Tip Grouted Drilled Shafts
… enhance both the usable and ultimate end bearing resistance. In short, postgrouting is a form of compaction grouting beneath the shaft tip (performed after concrete has cured) that can improve the soil strength and increase the axial shaft stiffness. Until 2006, there was no published design …
-
Fiber-Reinforced Plastic Composite Beam Stability and Load and Resistance Factor Design Approach
… experimental buckling loads. Lastly, a Load & Resistance Factor Design (LRFD) approach is presented and its use demonstrated by means of practical analysis and design examples.
-
Cost-Benefit Analyses for Load Resistance Factor Design (LRFD) of Drilled Shafts in Arkansas
… The analyses, specifically developed for load resistance factor design (LRFD) designed drilled shaft foundations, were designed to compare the fiscal impacts of the drilling and sampling, in-field and laboratory testing, full-scale load testing, and concrete mixing techniques utilized by the …
-
Membrane topology of a broad-spectrum resistance factor responsible for lipid modification in Enterococcus faecium.
… net negative charge of the membrane, conferring resistance to various classes of antibacterial agents (i.e., cationic antimicrobial peptides, beta-lactams, glycopeptides, and lipopeptides) and protecting the cell against osmotic stress and acidic conditions. aaPGS homologs are found in a variety …
-
Analysis of NEIL3 expression : a possible resistance factor to cancer chemotherapy in paediatric cancer cells
… ALL cell line. Therefore, NEIL3 could be a resistance factor to cancer chemotherapy in paediatric cancer cells and may be a novel target for the treatment of paediatric cancers.
-
Numerical Study and Load and Resistance Factor Design (LRFD) Calibration for Reinforced Soil Retaining Walls
Load and resistance factor design (LRFD) (often called limit states design (LSD)) has been mandated in the AASHTO Bridge Design Specifications and will be adopted in future editions of Canadian Highway Bridge Design Code for all transportation-related structures including reinforced soil retaining …
-
Load and resistance factor design of drilled shafts in shale using SPT and TCP measurements
… These methods are generally based on Load and Resistance Factor Design (LRFD) methods that relate uniaxial compressive strength measurements of rock cores to the side and tip resistance for drilled shafts. However, shale and other weak rock can be notoriously difficult to effectively sample and …
Page 1 of 12