Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 50 for “"SPECIMEN THICKNESS"”.
-
The Effect of Specimen Thickness on the Lüders Phenomena in AISI 1524 Steel Alloy
… aims to investigate the effect of the sample’s thickness on the Lüders phenomena in AISI 1524 hot-rolled steel alloy. Sixteen samples were machined from hot-rolled plates and uniaxial testing in conjunction with digital image correlation were performed to gain insight and quantify the Lüders …
-
The development of self-interference of split HOLZ (SIS-HOLZ) lines for measuring z-dependent atomic displacement in crystals
… enable measuring atomic displacement inside specimen. However, among all TEM techniques offering nano-scale resolution measurements, convergent beam electron diffraction (CBED) patterns show the highest sensitivity to the atomic displacement. Higher order Laue zone (HOLZ) lines split by small …
-
A Relationship Between the Strengths of Type N Cubic Mortar Specimens and In-Situ Mortar
… This disparity is a result of the differences in thickness, aspect ratio, curingconditions, water content, and confinement between mortar cubes and mortar joints. While thesedifferences lead to mortar joints being stronger than mortar cubes, a relationship between theirstrengths is desired.Two …
-
Scalability of cone calorimeter test results for the prediction of full scale fire behavior of polyurethane foam
… cone calorimeter incident heat flux setting, 2) specimen thickness and 3) ignition location on the predictive capability of the CBUF model. To provide input for the CBUF model cone and furniture calorimeter tests were conducted. Cone calorimeter tests were conducted on foam specimen thicknesses …
-
Experimental evaluation of J-integral for concrete subjected to impact loading
… to impact loading. Twenty four three-point bend specimens with two different thicknesses and mid-span notch lengths were tested under impact velocities of 167.22 in/sec (424.74 cm/sec) and 261.78 in/sec (664.92 cm/sec). Multi specimen method was used to analyze and estimate J<sub>I</sub> and its …
-
Effect of imaging conditions for reliable measurement of local strain from synthetic High Resolution Transmission Electron Microscope (HRTEM) images by Geometrical Phase Analysis (GPA)
… using Jems® simulation software with a model specimen consisting of a film of strained silicon on top of a relaxed Si0.82Ge0.18 alloy substrate in the [110] zone axis, where biaxial tensile strain exists in the strained silicon layer. Two simulated models are created: one with a sudden change …
-
Hole-drilling residual stress measurement in an intermediate thickness specimen
… to two extreme cases. In the “thick” case, the specimen depth is very large compared with the hole depth. The far boundary is then sufficiently distant that its effect can be neglected. In the “thin” case, the specimen has the form of a thin plate through which the hole penetrates fully. The …
-
Some Aspects of the Oxidative Stability of Cis-1, 4-Polyisoprene Vulcanizates
… cis-1,4- polyisoprene. Initially the effect of specimen thickness was investigated to ensure that diffusion controlled oxidation did not occur during the course of the oxygen uptake measurements. A comparison of several types of sulphur vulcanizates indicated that an efficiently cured system, …
-
The relationship between fracture toughness and shear lip size
… have been determined using compact tension specimens of varying thicknesses from 4 to 25mm. The size of the shear lips, BSL, measured at the free surfaces of the specimens was found to be independent of the specimen thickness and to be related to the true plane strain fracture toughness, …
-
An interfacial study of III-V materials
… and the AlAs-on-GaAs interfaces as a function of specimen thickness. The analysis of the images showed that the apparent interface widths varied with thickness in an unexpected manner. The measured GaAs-on-AlAs interface widths remained constant with thickness while the AlAs-on-GaAs interface …
-
Mechanical properties and microstructural characteristics of an Al-Mg alloy with bimodal grain size at room and elevated temperatures
… parameters including strain rate, temperature, specimen thickness, CG ratio, and anisotropy affect the mechanical properties of this material when tested in uniaxial tension. The material is fabricated through cryomilling, cold isostatic pressing, and extrusion. A full factorial experiment is …
-
An analysis of fretting fatigue
… of cylindrical fretting pads contacting a plane specimen is amenable to classical stress analysis and the surface tractions between the contacting bodies are derived. The effects of tension in the specimen, finite specimen thickness, differing elastic constants, and surface roughness are all …
-
Mechanisms of forming intergranular microcracks and microscopic surface discontinuities in welds
… speed were considered along with the effects of specimen thickness. The materials investigated were mild steel, aluminum, 304 stainless steel, titanium, and high strength steels, including HY-100, HY-130, and HSLA 100. The welding processes considered were electron beam (EB) welding, gas metal …
-
Assessment of mechanical properties and minimum printable thickness of definitive 3D-printed restorative materials across different printer platforms
… in vitro study evaluated the minimum printable thickness and mechanical properties of definitive 3D-printed restorative materials fabricated using different DLP printer platforms. The effects of material type and printer platform on dimensional accuracy, biaxial flexural strength (BFS), and …
-
Effect of specimen geometry and test configuration on the fracture process zone for asphalt materials
… eventually controls the global response of the specimen. I-FIT outputs are influenced by specimen geometry and test conditions (e.g., thickness, and loading rate, as well field aging). For this reason, there is a need to understand the effect of test parameters on global and microstructural …
-
Investigating the Effect of Thickness on Fracture Toughness of NiTi Shape Memory Alloy
… metals is believed to be dependent on specimen thickness especially due to the ductile fracture behavior of the material. On the other hand, due to the complex fracture behavior and the phase transformation characteristics of SMAs, the desire to explore the thickness effect on fracture …
-
Flammability Performance of Bio-derived Composite Materials for Aircraft Interiors
… the flammability properties of their respective specimens. An experimental study was also conducted, which compared flax fibre reinforced epoxy specimens to composites formed from glass fibre reinforcements of similar architecture, reinforcing the same resin system. The results demonstrated that …
-
Stresses around fasteners in composite aircraft structures and effects on fatigue life
… dimensional stress analyses of CFRP material specimens with holes, loaded in flexure in a cantilever-type of arrangement, the specimen being attached to a rigid support via bolts through the holes. The types of specimens studied were those used in experiments on a robust fatigue rig which was …
-
Tensile behavior of concrete and mortar under direct impact tensile load
… under direct tensile impact loading. A unique specimen was developed for this study based on a coaxial cylindrical design and is used to investigate the direct tensile behavior of cementitious composites. A specially instrumented drop weight testing apparatus was used for this study. Wave …
-
Resinas acrílicas utilizadas em placas estabilizadoras: resistência a fraturas e ensaio microbiológico
… and if the tested properties are related to thickness variation of these devices. The method included mechanical and microbiological steps, each one composed by Conventional (CG) (n=30), Milled (MG) (n=30) and Printed (PG) (n=30) groups, according to the method of preparation, each one having …
Page 1 of 3