Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 33 for “"Selective emitter"”.
-
Laser doped selective emitter solar cells
… schemes is an ideal combination. The benefits of selective emitter have been known and quantified for many years. However, the adaptation of selective emitter solar cell designs into mass-production has been quite slow due to the relatively complex processing steps involved in applying such a …
-
Aerosol Processing for Plated Selective-Emitter Silicon Solar Cells
… will require the minimisation of front surface (emitter) recombination after other significant loss components (i.e., rear surface and bulk recombination) have been minimised. A suggested path towards enabling higher commercially-produced cell efficiencies is through the implementation of a …
-
Laser-doped selective emitter and local back surface field solar cells with rear passivation
… of the rear surface and the formation of a selective emitter and local back-surface field by laser doping. One-sun implied Voc above 680 mV is achieved on commercial grade CZ p-type wafers when measured after laser doping and prior to metallisation. This is ~50 mV higher than the Voc …
-
Copper diffusion through plated nickel barrier layers for laser-doped selective-emitter silicon solar cells
… into mono-crystalline silicon laser-doped selective emitter (LDSE) solar cells. Energy dispersive X-ray spectroscopy was used in conjunction with transmission electron microscopy for chemical identification of copper-rich regions in silicon under the nickel/copper metal contacts of …
-
Numerical modeling and fabrication of high efficiency crystalline silicon solar cells
… promise to increase solar cell efficiency is a selective emitter solar cell. In this work the benefit of selective emitter solar cells is quantified through numerical modeling. Further, the use of ultraviolet laser to create a laser doped selective emitter solar cell is explored. Through …
-
Back contacting for crystalline silicon epitaxial thin-film solar cells
… two that most closely resemble the better known Emitter Wrap-Through back contact cell concept are the basic EpiWT concept and a similar version with a passivated selective emitter. The third version also has a passivated selective emitter but also introduces a reduced back-side emitter coverage, …
-
Simulation and characterization of novel large-area silicon solar cells for industrial production
… Three novel concepts are covered: the passivated emitter and rear cell, the selective emitter and the metal wrap through concept.
-
Inkjet printing for commercial high efficiency silicon solar cells
… high efficiency solar cell structures such as selective emitter, localised contacts, surface texturing and edge isolation are demonstrated using the indirect inkjet patterning method. Both inkjet patterning methods are then used in the fabrication of a selective emitter solar cell. Fill factors …
-
A study of thermal exchange in a thermophotovoltaic (Tpv) system at moderate temperature
… evacuated parallel-plate system consisting of an emitter and a photovoltaic (PV) material with the emitter temperature between 350K and 550K. Although higher temperature (and thus higher power output) thermophotovoltaic systems have been of interest previously, the focus here is on systems that …
-
Fabrication and modeling of high efficiency and stabilized P-type passivated emitter rear silicon solar cells (PERC)
… high-efficiency commercial-ready passivated emitter rear solar cells (PERC). Two specific aims are: 1) modeling and fabrication of high efficiency solar cells to reduce module cost for a given power output, and 2) reducing or eliminating of the widely observed light-induced degradation in …
-
Spectral and Directional Control of Thermal Emission with Nanophotonics
… including thermophotovoltaics (TPV), selective solar absorption, and infrared spectroscopy. Making it selective can greatly improve application performance. Here, selectivity is achieved using engineered photonic structures. Two specific design scenarios are discussed for different …
-
Laser Technology in the Fabrication of High Efficiency Solar Cells
… contact solar cells (BCSC) and laser doped selective emitter (LDSE) solar cells have achieved considerable success in large-scale manufacturing. Both of these technologies are based on plated contacts. The high metal aspect ratios achieved by BCSC allow for low shading loss while the buried …
-
High efficiency metal stencil printed silicon solar cells
… and 22-μm high. The best metal stencil printed, selective emitter silicon solar cell demonstrates a 34.2 mA/cm2 short circuit current density, 625 mV open circuit voltage, 0.77 fill factor and 16.4% efficiency, with an excellent spectral response at short wavelengths due to its selective emitter …
-
Development of commercial high-efficiency solar cells incorporating selective emitters and passivated rear contacts
… of solar cells, through the use of laser-doped selective emitter and localised rear contacts. This thesis begins with the development of laser-doped selective emitter (LDSE) technology to overcome the limitations of the front surface design associated with the industrial screen-printed solar …
-
Spherical Silicon for Photovoltaic Application: Material, Modeling, and Devices
… cells. A new device design with passivated selective emitter is proposed based on simulation results. Plasma processes were developed to selectively etch back the deep emitter of the spherical cells using reactive ion etching, and then passivate the surface using plasma enhanced chemical …
-
Point-contacting by Localised Dielectric Breakdown: self-aligned metallisation for a solar cell rear surface
… largely driven by new screen printed pastes and selective emitter technologies which have facilitated the use of high efficiency emitters. The rear surface offers next best way to increase cell efficiency by improving on the ubiquitous full area screen printed aluminium back surface field. A new …
-
Techno-Economic Analysis of Photovoltaic Technologies: methods to guide research and commercialisation
… back-surface-field (Al-BSF), Passivated emitter and rear cell (PERC), laser-doped selective emitter (LDSE), advanced hydrogenation and silicon heterojunction (SHJ) with both n-type and p-type wafers. This analysis showed there was good potential for the "PERC + LDSE", "advanced …
-
The impact of silicon nano-texture morphology on solar cell integration, performance, and degradation
… processes that are affected by nano-textures: emitter formation, surface passivation, and metal contact formation. Furthermore, it is identified that nano-texture may suppress light-induced-degradation (LID), however, the root cause of this behaviour is not understood. While fast diffusing …
-
Eutectic Sn-Bi Alloy for Interconnection of Silicon Solar Cells
… on n-type and p-type Cu contacts of laser-doped selective-emitter cells using light-induced and field-induced plating, respectively. The importance of uniformly reflowing the alloy after plating is demonstrated, with cells having plated Sn-Bi alloy and interconnected using Smart Wire Connection …
Page 1 of 2