Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 158 for “"Shear Testing"”.
-
Direct shear testing of marine sediment
… is complex. Specifically, the determination of shear strength of an unconsolidated- undrained sample by the direct shear method was found to exhibit an angle of internal friction ranging from 19 degrees to 23.5 degrees. This indicates that the shear strength of the sediments is dependent on the …
-
Shear Testing of Prestressed High Performance Concrete Bridge Girders
… BT-56 prestressed girder. It also details the shear testing and shear performance of the BT-56 girder. The results are compared with results from previous research dating back to 1986. Finally, all research was compared with the AASHTO Standard (2002), AASHTO LRFD (1998) and AASHTO LRFD (2004) …
-
Rail shear testing of composite materials: analysis and experiment
… analysis of selected graphite/polyimide rail-shear test specimens. The two-dimensional finite element analysis includes both mechanical and thermal loading (differential expansion) of the specimens and their elastic rails. Parameters in this analysis of unidirectional and symmetric angle-ply …
-
Quick Shear Testing of Aggregate Base Materials Stabilized with Geogrid
… was to apply a previously recommended laboratory testing protocol to specific aggregate base materials that are also the subject of ongoing full-scale field testing. The scope of this research involved three aggregate base materials selected from three sites where full-scale field testing programs …
-
Full-Scale Shake Table Cyclic Simple Shear Testing of Liquefiable Soil
… previously observed, or in tabletop laboratory testing. The study detailed herein is a controlled laboratory test performed at full scale to allow for the measurement of field-scale index testing before and after cyclic loading. Testing was performed at the Parson’s geotechnical and Earthquake …
-
Interlocking CSEB buildings Nepal Performance and failure behaviour investigated by masonry prism and triplet shear testing
… up Nepal, this thesis investigates methods of testing and possible improvements for interlocking CSEB masonry. By exploring how testing can be done in a simple way, which parts of the system contribute to overall strength, and what improvements are feasible in rural Nepal, this thesis aims to …
-
A Critical Laboratory Investigation of Multi-Stage Direct Shear Testing Procedures on Rock Joints Using Synthetic Replica Specimens
Direct shear testing is a common laboratory method used to define the geomechanical parameters of rock fractures for numerical inputs and rock engineering design. Of the standardized procedures, multi-stage direct shear testing is a controversial practice of repeatedly shearing the same rock joint …
-
Undrained Cyclic Loading of Low Plasticity Silty Soils in the Pacific Northwest Using Laboratory and Field Cyclic Shear Testing
… using a field and laboratory cyclic shear test program. The field cyclic tests were performed using the NHERI@UTexas large mobile shakers T-Rex and Rattler. The laboratory tests were performed using resonant column torsional shear and cyclic direct simple shear devices. This testing …
-
Development of a Multi-directional Direct Simple Shear Testing Device for Characterization of the Cyclic Shear Response of Marine Clays
… of a new multi-directional direct simple shear testing device, the Texas A&M Multi-directional Direct Simple Shear (TAMU-MDSS), for testing marine soil samples under conditions, which simulate, at the element level, the state of stress acting within a submarine slope under dynamic loading. …
-
Characterization of an interfacial fusion bonding model based on inter-layer shear testing and computationally predicted temperature history for additively manufactured amorphous thermoplastics
… Styrene (ABS) as the model material. Inter-layer shear specimens tested in a Boeing-modified ASTM D695 compression shear fixture isolated the weld response across a DoB range of 0.39 to 0.86, spanning limited interfacial wetting to near cohesive failure, with coefficients of variation below 5%. …
-
Shear design and behavior of ultra-high performance concrete
… objectives of this research are to develop a shear design procedure for possible code adoption and to provide a performance evaluation of structural testing to ensure the viability of the first UHPC bridge design in the United States. Two other secondary objectives will be helpful in this …
-
Comparing Sandwich Wall Panel Shear Connector Testing Methodologies
… rapid construction, and thermal efficiency. Shear connectors are used to connect the two wythes of concrete to allow composite action of the system. In order to design concrete sandwich panel systems to act compositely, the engineer must obtain design values from a connector manufacturer, …
-
Laboratory Investigation of Shear Behaviour in Rock Joints Under Varying Boundary Conditions
… design, is through laboratory direct shear testing. Direct shear testing is typically conducted using two different boundary conditions: constant normal stress (CNL*) and constant normal stiffness (CNS). The CNL* boundary condition represents fracture behaviour in slopes and near …
-
Biomechanics of the lower cervical spine during shear loading
The biomechanics of the cervical spine during shear loading are not well-established as compared to other loading regimes. This deficit may be problematic as there is evidence that shear loading may contribute to fracture-dislocation injuries, which often lead to spinal cord injury. Because of this …
-
THE SYNTHESIS AND CHARACTERIZATION OF DUAL-MODIFIED CARBOXYMETHYLCELLULOSE FOR BIOADHESIVE APPLICATIONS
… strength of the material was determined by lap shear testing with porcine skin. High molecular weight and medium molecular weight methacrylated dialdehyde carboxymethylcellulose (MeDCMCHV & MeDCMCMV) were engineered and MeDCMCHV was combined with low viscosity methacrylated CMC (MeCMCLV1) to …
-
Shear Bond Strengths of One and Two-Step Bonding Techniques on Extracted Teeth
The purpose of this research is compare shear bond strengths using two different self-etching methods and a conventional two step method (control) on brackets bonded to extracted human premolars five minutes and twenty-four hours after light curing. These three products will be compared in shear …
-
Effect of corticosterone injection on carbohydrate metabolism and tenderness of broiler breast muscle
… injection on post mortem muscle metabolism and shear resistance of Pectoralis Major muscle was studied. Short term studies, conducted over an 8 hour post-injection period, showed no significant effect of injection until 6 hours post injection at which time shear values increased from those of …
-
The development of DAPPAM, a glass fibre cable bolt
… cable bolt for mining applications. Laboratory testing consisted of tensile, preliminary shear, compression, grout column and Instron testing in addition to observations through the use of the scanning electron microscope at the University of British Columbia. Additional laboratory testing was …
Page 1 of 8