Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 43 for “"Sigma phase"”.
-
Factors affecting sigma phase precipitation in an austenitic stainless steel weld deposit
Includes bibliographical references.
-
Identification of sigma phase in superalloys by correlation with electronic and magnetic properties
Includes bibliographical references (pages 38-40).
-
Sigma phase in the ternary systems chromium-cobalt-copper and chromium-manganese-copper
… metallographic techniques and x-ray analysis the phases present in each alloy were determined and the two ternary isotherml sections constructed. It was found that copper had a very limited solid solubility in the sign phase of both systems. The sigma field in the Cr-Co-Cu 1000°C. ternary …
-
The effect of carbon on the formation of sigma phase in austenitic stainless steel
… (and chromium content) on the amount and rate of sigma phase formation in experimentally prepared iron-chromium-nickel-carbon alloys. Nine alloys were melted in a laboratory under vacuum or controlled atmosphere using high-purity raw materials as ingredients. The compositions were typically in the …
-
Delta-ferrite transformation to M₂₃C₆ carbide, austenite, and sigma phase in AISI 304L austenitic stainless steel
Includes bibliographical references.
-
Factors affecting the constitution and stability of iron-base austenitic alloys.
… by analysing the composition of the individual phases by a micro-probe technique. The transformation of the delta ferrite, during the isothermal heat treatments, to either austenite or (austenite + sigma phase) has been investigated. In the sigma phase regions the delta ferrite transforms first …
-
Abrasive wear resistance of ruthenium aluminide intermetallic and ferritic steels containing a sigma intermetallic phase
… and ferritic steel containing an iron-chrome sigma intermetallic phase have been investigated in this study. A medium carbon wear resistant steel (MCV) was used in the study to facilitate comparison between wear resistances in the materials of interest. Specimens of ruthenium aluminide, MCV …
-
Some aspects of the thermal stability of 316L weld metal
… formation of the brittle, intermetallic compound sigma phase. The thermal stability of welds is often found to be lower than that of the base metal. This effect is most often linked to the presence of ferrite in the weld deposit which greatly increases the rate of sigma formation. The presence of …
-
Phase stability, constitution and precipitation effects in Fe-Ni-Cr alloys.
… and precipitation of intermetallic phases and carbides in the aged microstructures.The transformation of delta ferrite to sigma phase in a duplex (gamma+delta) ternary alloy was studied. The transformation was preceded by the precipitation of a cellular structure which formed on the …
-
The Cr₃O-type compound in the niobium-rhodium-silicon ternary system
… contains niobium plus an unidentified phase assumed to be Nb₅Si₃. The Nb-Rh sigma phase extends into the ternary system to at least 10 atomic percent silicon. All ternary alloys investigated contained three phases. These phases were one or more unidentified phases combined with either …
-
Kinetic and Thermodynamic Modeling of Long Term Phase Stability in Alloy 800H Subjected to LWR Core Conditions
… evolution under irradiation and secondary phase precipitate stability. Due to a lack of radiation induced segregation (RIS) data for Alloy 800H, Isopleth sections varying Cr, Ni, Ti, and Si were generated from a computational thermodynamics approach using ThermoCalc and analyzed to …
-
Investigation into the transformation products of CD3MN cast duplex stainless steel
… The primary research evaluated the kinetics of sigma ([Sigma]) phase formation by developing the time-temperature-transformation diagram for CD3MN and comparing these results to wrought duplex stainless steel transformation diagrams. The results of the study showed that the nose of the …
-
The Effects of Weld Thermal Cycles on Additively Manufactured 316L Stainless Steel
… on the interelayer temperatures and sigma phase determination should be conducted to confirm the hypotheses to explain the phenomena observed in this study.
-
High-temperature deformation and environment-induced degradation of Waspaloy
… possibly due to the formation of brittle sigma phase. The cracking susceptibility of Waspaloy in an acidic solution was enhanced at a higher temperature when tested by the slow strain rate (SSR) technique. Slight variations in ductility parameters, true failure stress and time to failure …
-
Characterization of thermal damage in 2205 duplex stainless steel with nonlinear ultrasonics (nlu)
… which leads to the development of a third (sigma) phase, and thus to a change in material properties. The objective of this research is to assess the material damage in thermally degraded 2205 duplex stainless steel using nonlinear ultrasonics (NLU). Seven 2205 duplex stainless steel …
-
Corrosion performance of an austenitic stainless steel fabricated by wire arc additive manufacturing.
… the transformation of delta ferrite into sigma leading to its complete transformation of during the heat treatment, decreasing corrosion performance. The study identified that microstructural differences between as-deposited WAAM and wrought alloys are linked to differences in pitting …
-
Investigating the heat-treatment process for 316L alloy powders with the application in binder jetting metal additive manufacturing
… with an Energy-dispersive detector. Detrimental sigma-phase was identified in the sintering 316l microstructure. A solutionizing post-heat treatment has been developed to re-solution the sigma-phase into ferrite. The work done on the powder properties and green density will be used as the basis …
-
Cross-frequency coupling and sleep-dependent declarative memory consolidation: sleep states as opponent processes
… In non rapid-eye-movement sleep (NREMS), delta-sigma phase-amplitude coupling (PAC) was marginally increased in central regions after learning, and its learning-related change in frontal regions was strongly predictive of recall performance the next morning. We observed opposite effects for CFC …
-
Solidification behavior and texture of laser-wire directed energy deposition of 316L austenitic stainless steel
… 900°C resulted in an increase in hardness due to sigma phase formation. Variation in hardness between samples heat treated at the same conditions is attributed to differences in the volume fraction of sigma phase due to differences in the initial delta-ferrite volume fraction in the as-built …
-
Κραματωμένες επικαλύψεις με τη τεχνική μεταφερόμενου τόξου πλάσματος
… The existence of chromium nitrides or sigma - phase deteriorated the anti-corrosive behavior of the produced coatings, since chromium did not spread uniformly through the whole matrix. In a next step, the production of coatings with 100% austenitic microstructure and with low nickel …
Page 1 of 3