Global ETD Search

Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.

Results

Showing 1 to 20 of 49 for “"Single-lap shear"”.

  1. Cure Dependent Viscoelastic-Plastic Modeling of Adhesives to Capture CTE Effects in Multi-Material Structures

    … the structure were run at coupon level using a single lap shear geometry and at component level on a scaled-down automotive roof component. The other set of tests were done to determine the effect of manufacturing induced residual stresses on the performance of the adhesive joint. This work …

    clemson Repository record for Cure Dependent Viscoelastic-Plastic Modeling of Adhesives to Capture CTE Effects in Multi-Material Structures (opens in a new tab)

  2. BOND STRENGTH EVALUATION IN ADHESIVE JOINTS USING NDE AND DIC METHODS

    … defects and reliably predicting the bond shear strength. As a result, adhesive bonding technology is still not solely implemented in primary structures of an aircraft. Therefore, there is a greater demand for a novel NDE tool that can meet the existing aerospace requirement for adhesive …

    siu-theses Repository record for BOND STRENGTH EVALUATION IN ADHESIVE JOINTS USING NDE AND DIC METHODS (opens in a new tab)

  3. Development of High Performance Hierarchical Multi-Functional Ceramic Nanocomposites Employing Carbon-Nanotube Nanoforest and Pre-Ceramic Polymers

    … and tested using a 4-point bending method, single lap shear method, and single specimen double shear bolted joint method. Four-point bending test [1] was also conducted at room temperature to evaluate the flexural mechanical performance of six different CFCC’s (i.e., those with MPs and NPs, …

    hawaii Repository record for Development of High Performance Hierarchical Multi-Functional Ceramic Nanocomposites Employing Carbon-Nanotube Nanoforest and Pre-Ceramic Polymers (opens in a new tab)

  4. Constitutive Property Testing and Reliability Assessment of Lead-Free Solder Joint

    A modified single lap shear test configuration, based on the Iosipescu geometry, is proposed to characterize mechanical properties of solder alloys. In the method, an auxiliary device (extension unit) is employed to improve the accuracy of measurement. The extension unit is attached directly to the …

    maryland Repository record for Constitutive Property Testing and Reliability Assessment of Lead-Free Solder Joint (opens in a new tab)

  5. Development of Bio-based Wood Adhesive by Using Cellulose Nanofiber Reinforcement and Crosslinking Agent for Improved Bonding Strength

    … and a crosslinking agent was also used. Single-lap shear test, flexural and internal bond tests were performed on dry and water-immersed samples to measure the bond strength. Fractured bond surfaces were studied using optical observation and scanning electron microscopy (SEM) to determine …

    ndsu Repository record for Development of Bio-based Wood Adhesive by Using Cellulose Nanofiber Reinforcement and Crosslinking Agent for Improved Bonding Strength (opens in a new tab)

  6. Calibration of Alumina-epoxy Nanocomposites Using Piezospectroscopy for the Development of Stress-sensing Adhesives

    … were applied to an alumina-filled adhesive in a single lap shear configuration demonstrating the capability of the technique to monitor R-line peak positions with high spatial resolution and assess the stress distribution within the material prior to failure. Additionally, particle dispersion and …

    ucf Repository record for Calibration of Alumina-epoxy Nanocomposites Using Piezospectroscopy for the Development of Stress-sensing Adhesives (opens in a new tab)

  7. Effect of surface treatments on interfacial strength and durability of metal-polymer composite bond

    … temperature curing epoxy) bond was studied using single lap shear, flatwise tensile and wedge crack test. The interfacial strength (IFSS) and % cohesive fracture varied with composite adhesive thickness and 0.03-0.04 mm that maximized the interfacial fracture was chosen to compare surface …

    manitoba Repository record for Effect of surface treatments on interfacial strength and durability of metal-polymer composite bond (opens in a new tab)

  8. Experimental Testing and Modelling of Adhesively Joined T-structures

    … were undertaken including quasi-static direct shear (2.5 mm/min), quasi-static torsion (2.5 mm/min), unsupported dynamic impact shear (4.43 m/s) and supported dynamic impact shear (3.96 m/s). Surface preparation is an important component when assessing the strength of the adhesive. Grit …

    waterloo Repository record for Experimental Testing and Modelling of Adhesively Joined T-structures (opens in a new tab)

  9. Large-Scale Externally Bonded Fibre-Reinforced Polymer Systems for Tension Strengthening of Existing Reinforced Concrete Structures with and without Fibre Anchors

    … thin, short EB-FRP systems for flexural or shear strengthening and do not capture the bond and anchorage mechanisms of large-scale EB-FRP required for tension strengthening applications. Anchorage behaviour for multi-anchor configurations remains insufficiently characterized, resulting in …

    auckland-ms Repository record for Large-Scale Externally Bonded Fibre-Reinforced Polymer Systems for Tension Strengthening of Existing Reinforced Concrete Structures with and without Fibre Anchors (opens in a new tab)

  10. Impact of recycled plastic content on bond line performance

    … and the strength of the joints was measured with single lap shear tests after curing and ageing. Surface analysis measurements of surface free energy, cleanliness, and surface roughness were also done to see the differences among the materials and how the surface properties changed after …

    chalmers Repository record for Impact of recycled plastic content on bond line performance (opens in a new tab)

  11. Structural health monitoring in adhesively bonded composite joints

    … a simple, state-of-the-art composite single lap shear joint is selected for experimentation and analysis to measure and quantify the effect of incorporating a sensor within the bondline to evaluate and expand on the ability of the embedded sensor to monitor and assess the joint …

    colostate Repository record for Structural health monitoring in adhesively bonded composite joints (opens in a new tab)

  12. TEMPERATURE AND RATE DEPENDENT PARTITIONED CONSTITUTIVE RELATIONSHIPS FOR 95.5PB2SN2.5AG SOLDER ALLOY

    … and strain rates utilizing miniature single-lap shear specimens, with a partitioned form of the general constitutive equation.

    maryland Repository record for TEMPERATURE AND RATE DEPENDENT PARTITIONED CONSTITUTIVE RELATIONSHIPS FOR 95.5PB2SN2.5AG SOLDER ALLOY (opens in a new tab)

  13. Photoactivated Fixation of Cartilage Tissue

    … cartilage tissues was performed using a modified single-lap shear test. Finally, the cellular viability and bond stability of a photochemically bonded cartilage interface was evaluated over seven days of in vitro culture, where the bond strength was assessed by pushout of cores from annular …

    gatech Repository record for Photoactivated Fixation of Cartilage Tissue (opens in a new tab)

  14. The development of poly(vinylidene fluoride) piezoelectric sensors for measuring peel stresses in adhesive joints

    … in both the elastomeric butt joint and the single lap shear joint were measured using the developed stress sensors. Comparison of the measured stresses with calculated values obtained from closed-form analytical solutions and finite element analysis for the stresses was excellent. The …

    vt Repository record for The development of poly(vinylidene fluoride) piezoelectric sensors for measuring peel stresses in adhesive joints (opens in a new tab)

  15. Synthesis and characterization of phenylethynyl endcapped polyetherimide oligomers

    … surface treated titanium alloys were produced by single lap shear measurements. Resin infusion molding has been conducted that permitted low void graphite fabric composite panels to be prepared. The diamine monomer bis(m-aminophenyl) methyl phosphine oxide (DAMPO) was synthesized via nitration and …

    vt Repository record for Synthesis and characterization of phenylethynyl endcapped polyetherimide oligomers (opens in a new tab)

  16. Adhesion study of thermoplastic polyimides with Ti-6Al-4V alloy and PEEK-graphite composites

    … test temperature, and polyimide structure via single lap shear samples prepared from treated Ti-6AI-4V alloy adherends and compression molded film adhesives or scrim cloth adhesives. The adhesive bond strengths increased greatly with siloxane segment incorporation at 10, 20 and 30 weight …

    vt Repository record for Adhesion study of thermoplastic polyimides with Ti-6Al-4V alloy and PEEK-graphite composites (opens in a new tab)

  17. Effect of Surface Treatment on Joint Performance and Fracture Morphology in Adhesively Bonded Al-Si Coated Ultra-High Strength Steel

    … joined adherends were evaluated using the single-lap shear (SLS) test to investigate the nine material conditions (three surface treatments, three steel thermal processing treatments). The measured joint strength of the GB and AP conditions were 60% and 56%, respectively, higher than the …

    waterloo Repository record for Effect of Surface Treatment on Joint Performance and Fracture Morphology in Adhesively Bonded Al-Si Coated Ultra-High Strength Steel (opens in a new tab)

  18. The Behaviour of Cold-Formed Steel Built-up Structural Members

    … built-up specimens was determined by means of single lap shear tests. Detailed finite element models were created of the built-up beams and columns, which included the material non-linearity obtained from the tensile coupons, the geometric imperfections recorded on the actual specimens and the …

    whiterose Download PDF for The Behaviour of Cold-Formed Steel Built-up Structural Members (opens in a new tab)

  19. Data-Driven Thermal Modeling and Interlaminar Bond Improvement for In-situ Automated Fiber Placement (AFP) of Thermoplastic Composites

    … both modes, bond strength was measured through Single Lap Shear (SLS) tests. Results from the in-situ treatment were compared with those from autoclave-consolidated, in-situ AFP-consolidated, and in-situ repassed samples. The proposed in-situ treatment achieved near-autoclave-level bond strength …

    concordia Download PDF for Data-Driven Thermal Modeling and Interlaminar Bond Improvement for In-situ Automated Fiber Placement (AFP) of Thermoplastic Composites (opens in a new tab)

Page 1 of 3