Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 21 for “"Single-tracks"”.
-
From recycled machining waste to useful powders: sustainable fabrication and utilization of feedstock powder for metal additive manufacturing
… powder created from machining chips in metal AM, single tracks (ST) have been successfully deposited via laser engineered net shaping (LENS®) and compared to the single tracks made from GA powder (ST-GA) using identical deposition conditions. The microstructures of these single tracks exhibited …
-
Development of a Process Parameter Selection Guideline for Additively Manufacturing New Materials Via Laser Powder Bed Fusion
… mitigating lack of fusion. Characterization of single tracks and cubes is performed to explore the relationship between process parameters and porosity and differential evaporation of a binary nickel alloy.
-
SLM 125 Single Track and Density Cube Characterization for 316L Stainless Steel
… investigates system capabilities when melting single tracks of material. Individual tracks allow for a wide range of scan speeds and laser powers to be utilized and the melt pools analyzed. I discuss how existing studies and simulations can be used to narrow down the selection of potentially …
-
Process Monitoring and Defect Detection of Additive Manufacturing Using Inline Coherent Imaging
… 45 $\mu m$ 316L stainless steel. Imaging of both single and multilayer builds is performed at a rate of 200 $kHz$, with a resolution of tens of microns, and a high dynamic range rendering it impervious to blinding from the process beam. This allows imaging before, during, and after laser …
-
Multiscale investigation on surface integrity and performance of metal parts by selective laser melting
… metallurgical, and mechanical properties of single tracks under a broad range of processing conditions in SLM of IN625 alloy; (3) A comprehensive investigation of microstructural evolution of IN625 alloy from as-SLM to different heat treatment conditions; (4) Two efficient multi-physics …
-
Efficient physics signal selectors for the first trigger level of the Belle II experiment based on machine learning
… estimates the 3D track parameters of the single tracks found by a 2D Hough finder. The neural networks are already implemented on parallel FPGA hardware for real time data processing and running pipelined in the online first level trigger of Belle II. Due to the anticipated high luminosity …
-
Development of a Novel Additive Manufacturing Process using Material Extrusion for the Production of Porous Titanium Orthopaedic Implant Material
… bespoke 3D structures through the deposition of single tracks and building up successive layers, whilst still maintaining the optimised porous structure of the material. This research demonstrates the feasibility of this novel manufacturing method which offers the capability of producing …
-
Rapid Thermo-mechanical Modeling of Laser Powder-Bed Fusion Additive Manufacturing using an Effective Heat Source
… melt pool dimensions of Hastelloy X material single tracks were measured experimentally. Afterward, the micro/mesoscale simulation of LPBF single track was conducted, while implementing a volumetric heat source model (conical-Gaussian) to extract the transient temperature profile and melt pool …
-
Desarrollo y caracterización de recubrimientos TiAl mediante procesado láser coaxial sobre Ti6Al4V
… and chemical dilution analysis of the single tracks obtained at different levels in the laser processing variables were able to identify combinations that minimize defects such as cracks, high dilution and inadequate aspect ratio. It found a direct relation between the cooling rate and …
-
Evaluation of load capacity of concrete railway slab spans with defects
… of construction. Moreover, the spans carrying single tracks dominate in this group. The statistical information based on these sources has been presented in this study. Based on the Author’s observations, consultations with bridge inspectors as well as the literature study, a uniform and …
-
Integration of a Chromatic Aberration Technique for In Situ Working Distance Measurement During Powder Blown Laser Directed Energy Deposition Additive Manufacturing
… for two different materials using a series of single-track prints; the heights of these single-tracks are then measured using a profilometer. Since the radiation spectrum depends on the temperature of the emitting surface; the calibration curve is unique to each material with its specific …
-
Functionally Graded Additive Manufacturing of Inconel 625 and CuCrZr Alloys
… such as combining multiple alloys within a single build to create functionally graded structures, eliminating the need for additional joints. In that regard, Functionally Graded Additive Manufacturing (FGAM) is a layer-by-layer process that varies composition and/or microstructure within a …
-
Process Parameter Optimization for Crack Mitigation in CM247LC processed by Electron Beam Powder Bed Fusion
… This started with the basic deposition unit of a single-track and later progressed with multi-tracks. An experimental single-track study, structured within a design of experiment (DoE) framework, was conducted to isolate the primary EBM process parameters and evaluate their effects on the track …
-
Process Optimization, Numerical Modelling, and Microstructure Control in Laser Powder Bed Fusion of Ti-5553 Parts
… the properties of printed parts, an integrated single-track to multi-layer method was systematically employed. An investigation into the track morphology, melt pool geometry and melt pool microstructure composted of single-tracks was compared with a range of microscopic examinations and X-ray …
-
Experimental and numerical study of process parameters effects towards part quality and porosity during powder bed additive manufacturing processes.
… the effect of powder distribution towards the single-track formation during the laser powder bed fusion (LPBF) process. The numerical results show that the single-track morphology and density depend on the process parameters: scanning speed and laser power. Besides, micro-computed tomography …
-
OPTIMIZATION OF LASER POWDER BED FUSION PROCESS IN INCONEL 625 TOWARDS PRODUCTIVITY
… on determining the process window, for which single tracks were printed with two high levels of laser power (300, 400 W), five levels of scan speed (500, 700, 900, 1100, 1300 mm/s), and five levels of powder layer thickness (30, 60, 90, 120, 150 µm). Then, the process window was defined after …
-
Experimental and numerical studies of laser powder-bed fusion process with ti-6al-4v powder: (1) porosity and mechanical properties, and (2) transient phenomena in one- and two-dimensional fabrications.
… of microns interacts with metal powder to form tracks. The laser follows predefined scan paths in each layer, and the behavior of the melt pool during each scan is heavily influenced by the laser power and scan speed. The melting process can occur in three modes: incomplete melting, conduction …
-
Characterization and Simulation of the Microstructure of Additively Manufactured Hastelloy X Parts with Columnar Grain Structure
… is necessary to have consolidated layers made of single lines. Thus, an in-depth understanding of the effect of key process parameters on fast solidification is required to produce condensed layers leading to high-quality parts with low porosity and high strength. Poorly selected parameters result …
-
Mechanisms of Hot-Cracking During Electron Beam Powder Bed Fusion of Co-29Cr-10Ni-7W Alloy
… from the top surface. Numerical simulation of a single scan using ANSYS-APDL software was carried out to illustrate how the scan direction may relate to directions of thermal stresses during track solidification. Finally, single track experiments by having a single track in the last layer were …
-
Multi-Scale Modeling of Laser Powder Bed Fusion Process for Superalloys
… part of the simulation. This includes printed single tracks on a layer of RENÉ 65 powder using six different laser speeds and three different laser powers. The results showed that the HL and ED models are equally accurate in predicting cooling rates and nodal temperatures, essential to simulate …
Page 1 of 2