Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 327 for “"Slenderness"”.
-
Slenderness of masonry block walls
The slenderness effect of masonry walls is examined through the combination of existing analytical methods and experimental results for masonry walls. The current code design capacities, when compared with the theoretical values, are found to be inconsistent and over-conservative. A Limit State …
-
Slenderness effects in prestressed concrete columns
The purpose of this investigation was to compare the behaviour of real prestressed concrete columns to the predictions of a mathematical model. A previously developed computer programme, based on the mathematical model, had suggested several problems which needed examination. The programme …
-
The Bracing Requirements of Steel Beams of Intermediate Slenderness
… elastic or inelastic conditions depending on the slenderness of the member. A review of the literature pertaining to the bracing requirements of steel beams revealed little published work concerned with the restraint of beams of intermediate and low slenderness which fail inelastically. The …
-
Lower limit of influence of slenderness on the strength of reinforced concrete columns
Bibliography: leaf [12]-[17]
-
INVESTIGATION INTO THE EFFECT OF SLENDERNESS RATIO ON RE-ENTRANT HONEYCOMB MECHANICAL PROPERTIES
Thesis (M.S.)--Michigan State University. Civil Engineering - Master of Science, 2024
-
Simultaneous effect of slenderness, spatially varying excitation and support flexibility on dynamics of rocking bridges
… interpretations of the result. The effect of slenderness on bridge responses with a rigid support was considered first. The result revealed complex girder-pier-footing interactions. Building upon these results, the subsequent experiments were performed on the bridge-soil system under …
-
Experiments to Understand the Impact of Local and Global Slenderness on the Inelastic Deformation Capacity of Square and Round HSS Braces
… component in CBFs and limits on their local slenderness (i.e., width-to-thickness or diameter-to-thickness) defined in the AISC Seismic Provisions (AISC 341-22) are used to achieve a target ductility and drift range capacity for OCBF and SCBF systems. To evaluate these limits, a comprehensive …
-
The Effect of Foam Core Density on the Flexural and Axial Behaviour of Sandwich Panels of Varying Slenderness with Natural Flax-FRP and Glass-FRP Composite Skins
… and axially compressed columns of varying slenderness and skin thickness. Bio-composite unidirectional flax fibre-reinforced polymer (FFRP) is compared to conventional glass-FRP (GFRP) as the skin material used in conjunction with three polyisocyanurate (PIR) foam cores with densities of …
-
Experimental and Analytical Investigations of Doubly Symmetric Built-Up I-Girders with Large Moment Gradient Factors
… bending that have unstiffened webs, a large web slenderness ratio, and a high moment gradient factor resulting in a high shear-to-moment ratio. To further investigate these reductions, this study evaluated six experimental specimens and a suite of complimentary parametric finite element analysis …
-
DESIGN METHODS FOR LARGE RECTANGULAR INDUSTRIAL DUCTS
… in terms of dimensionless pressure, plate slenderness and normalized out-of-plane deflection for three cases namely; 0%, 16.5% and 33% of through thickness yielding of the plate. Results show that approximately 50% increase in stiffener spacing when yielding of 16.5% of thickness is …
-
Comparative Design Analysis of Stainless-Steel Hollow Sections
… determination of the bending resistance, global slenderness, and local slenderness, considering austenitic, ferritic, and duplex stainless-steel grades. A literature review of the different design standards and baseline information about stainless steel and its applications in structural …
-
The instability of slender reinforced concrete columns. A buckling study of very slender reinforced concrete columns between the slenderness ratios of 30 and 79 Including essential creep investigations, and leading to design recommendations.
… reinforcements with lateral ties were cast. Slenderness rates, L A, were varied from 30 to 79. Special factors were obtained to relate the actual modulus of elasticity of concrete in columns at buckling failure to a knowledge of the initial modulus of elasticity of concrete in control …
-
Assessing and promoting windfirmness in conifers in British Columbia
… and sample trees represented a range of stem slenderness in the thinned and control portions. Following thinning, height increment was temporarily reduced, radial increment increased and the allocation of radial increment became more basal in each of the three thinning treatments. The …
-
Experimental Investigation to Compare the Cyclic Response of A500 and A1085 HSS Braces
… years, in particular due to the stringent local slenderness requirements for ductile members and the Ry factor. Traditionally, ASTM A500 HSS sections are used in SCBFs. However, AISC 341 now permits the use of ASTM A1085 HSS sections. The ASTM A1085 specification requires tighter control over the …
-
Three-dimensional elasticity models for buckling of anisotropic and auxetic beams and plates
… beams obtained well results for large slenderness ratios when it compared with Euler-Bernoulli theory which is considered in this study the main area of comparison study. For small values of slenderness ratio the elasticity theory obtained significant difference than the Euler-Bernoulli …
-
Hollow Structural Sections in Flexure
… rectangular sections with relatively low flange slenderness. The present work attempts to relate the tube slenderness and yield strength to the rotation capacity and moment resistance of round sections subjected to bending moment. Also an attempt is made to establish similar guidelines for …
-
Performance evaluation of high-strength concrete circular columns reinforced with GFRP bars and spirals
… (steel or GFRP), spiral pitch (50 or 85 mm), slenderness ratio (14, 20 or 28), the level of axial load eccentricity (60, 90, 120 or 150 mm) and the loading type (axial or flexural loading). The experimental results were then compared to the predictions of the Canadian and American FRP design …
-
TOWARDS THE RECONCILIATION OF THE EMPIRICAL AND RATIONAL DESIGN PROVISIONS OF CSA S304-14
… include mortar type, support conditions, wall slenderness ratio, and the load application method. An experimental program was conducted to provide additional data in areas where test data was lacking: walls constructed using mortar cement mortar, walls with slenderness ratios equal and greater …
-
An experimental investigation of spirally prestressed concrete columns.
… of the effects of initial prestress and slenderness ratios on the ultimate load carrying capacity of spirally prestressed concrete columns. The experimental investigation was carried out on 6 inch diameter concrete columns. The program was divided into series A, B, C and D with …
Page 1 of 17