Global ETD Search

Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.

Results

Showing 1 to 20 of 116 for “"Spray cooling"”.

  1. Spray cooling with R134a

    Spray cooling is a high heat flux cooling technique, which can be used to cool solid state laser diodes and other high heat flux electronic devices. This study will investigate the beat transfer coefficients obtained when spray cooling with Rl34a. The experiment will u e a single nozzle and a 1 cm2 …

    ucf Repository record for Spray cooling with R134a (opens in a new tab)

  2. Drop impact in spray cooling

    Spray cooling has enormous potential in addressing high-heat-flux thermal challenges in many cutting-edge technologies. In spray cooling, a flow of coolant drops is emitted from a spray nozzle and impacts a hot surface, which is covered by a flowing film. Heat transfers by convection from the …

    ubc Repository record for Drop impact in spray cooling (opens in a new tab) Download PDF for Drop impact in spray cooling (opens in a new tab)

  3. Investigation of Enhanced Surface Spray Cooling

    … passive refrigeration cycles to semiconductor cooling. The primary heat transfer techniques associated with phase change heat transfer are pool boiling, flow boiling, and spray cooling. Of these techniques, spray cooling is the least studied and the most recent to receive attention in the …

    maryland Repository record for Investigation of Enhanced Surface Spray Cooling (opens in a new tab)

  4. Spray cooling applications for alternative energy vehicles

    … induced drag. Here we examine utilizing water to spray onto the heat exchangers to increase performance, allowing a decrease in surface area required for heat exchangers in alternative fuel source vehicles. The scalable and optimized super hydrophilic heat exchangers developed here at UIUC have …

    uiuc Repository record for Spray cooling applications for alternative energy vehicles (opens in a new tab)

  5. An investigation of heat transfer in spray cooling

    Spray water fluxes .and heat-transfer coefficients have been measured for some commercial spray nozzles, with a view to generating reliable and accurate data for the design of spray chambers of continuous casting machines. Sprays produced by both full cone and vee-jet nozzles have been …

    ubc Repository record for An investigation of heat transfer in spray cooling (opens in a new tab) Download PDF for An investigation of heat transfer in spray cooling (opens in a new tab)

  6. PRESSURE-BASED PREDICTION OF SPRAY COOLING HEAT TRANSFER

    One of the main challenges of spray cooling technology is the prediction of local and average heat flux on the heater surface. It has been suggested that spray cooling heat transfer depends on the local spray mass flux. However, in this work it is hypothesized and demonstrated that local …

    maryland Repository record for PRESSURE-BASED PREDICTION OF SPRAY COOLING HEAT TRANSFER (opens in a new tab)

  7. Alumina Nanofluid for Spray Cooling Heat Transfer Enhancement

    … in such applications. The use of nanofluids for spray cooling is an extension of the application of nanofluids for enhancement of heat dissipation. In this investigation, experiments were performed to determine the level of heat transfer enhancement with the addition of alumina nanoparticles to …

    usf Repository record for Alumina Nanofluid for Spray Cooling Heat Transfer Enhancement (opens in a new tab)

  8. Heat Transfer Enhancement of Spray Cooling with Nanofluids

    Spray cooling is a technique for achieving large heat fluxes at low surface temperatures by impinging a liquid in droplet form on a heated surface. Heat is removed by droplets spreading across the surface, thus removing heat by evaporation and by an increase in the convective heat transfer …

    usf Repository record for Heat Transfer Enhancement of Spray Cooling with Nanofluids (opens in a new tab)

  9. Investigation of Spray Cooling Schemes for Dynamic Thermal Management

    … investigate variable flow and intermittent flow spray cooling characteristics for efficiency improvement in active two-phase thermal management systems. Variable flow spray cooling scheme requires control of pump input voltage (or speed), while intermittent flow spray cooling scheme requires …

    unt Repository record for Investigation of Spray Cooling Schemes for Dynamic Thermal Management (opens in a new tab)

  10. Mill roll profile control by means of spray cooling

    … in order to simulate the effectiveness of each spray zone in removing heat from the roll. A simplified method of evaluating roll thermal cambers, derived from the model, is presented. The model shows good agreement between predicted and measured roll thermal cambers.The model is linked to a …

    bournemouth Download PDF for Mill roll profile control by means of spray cooling (opens in a new tab)

  11. Development of Spray Cooling for High Heat Flux Electronics

    … systems require innovative thermal solutions. Spray cooling has proven to be able to cool heat fluxes orders of magnitude higher than traditional cooling methodologies. This work includes a comparison of spray cooling to standard thermal management methodologies. Key system parameters and …

    arkansas Repository record for Development of Spray Cooling for High Heat Flux Electronics (opens in a new tab)

  12. Control of spray cooling in the continuous casting of steel

    The basic principles of spray control during casting speed changes in the continuous casting of steel have been studied. The normal spray control practice in which water flow in the sprays is made proportional to the casting speed has been found to be completely inadequate from the standpoint of …

    ubc Repository record for Control of spray cooling in the continuous casting of steel (opens in a new tab) Download PDF for Control of spray cooling in the continuous casting of steel (opens in a new tab)

  13. High Heat Flux Spray Cooling With Ammonia On Enhanced Surfaces

    … task include several single and two phase cooling options. When these cooling schemes are compared based on the high heat flux removal (100-1000 W/cm2) and isothermal operation (within several oC across the cooled device) aspects, as well as system mass, volume and power consumption, spray …

    ucf Repository record for High Heat Flux Spray Cooling With Ammonia On Enhanced Surfaces (opens in a new tab)

Page 1 of 6