Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 19 of 19 for “"Square Tube"”.
-
Pitch and Clearance Effects on Stability of Loosely Supported Rotated Square Tube Bundles
… of structural supports in preventing SFEI. Tube-to-support clearance has emerged as a critical parameter influencing the behavior of tube bundles. This thesis investigates the effects of radial clearances on a loosely supported rotated square tube bundle, specifically examining radial …
-
Development Of Design Equations For A Square-tube Subbase Supporting A Shaft-mounted Speed Reducer
… as a function of three subbase parameters: tube thickness, mounting strap width, and end cap thickness. Developing design equations by analytical methods is investigated first. Next, finite element models are used to check the analytical results for accuracy. Finally, finite element models …
-
Multiobjective Optimization of Composite Square Tube for Crashworthiness Requirements Using Artificial Neural Network and Genetic Algorithm
… force and specific energy absorption for a square tube. The design variables include the number of plies, ply angle and ply thickness of the square tube. To obtain an effective approximation an artificial neural network (ANN) is used. Training data for the artificial neural network is …
-
Dynamic measurements with a luminescent photoelastic coating
… The dynamic tests involved bar specimens and square-tube specimens loaded at 1 Hz and 10 Hz. Instead of continuous excitation, strobed excitation was phase-synchronized with the frequency of the specimen. The experimental set-up and results are discussed.
-
Rotors for Moving Frames in Projective Geometric Algebra
… by iteratively applying them to the corners of a square to construct a square tube fitted around a helix. We also generalize the construction of the rotors associated with moving frames to an arbitrary number of dimensions. We thus further develop the use of PGA in the field of differential …
-
Thin-walled tubes with pre-folded origami patterns as energy absorption devices
… of energy absorption device made of thin-walled tubes. The tubes will undergo plastic deformation when subjected to an impact loading, and therefore absorb kinetic energy. It has been found that, if the surface of a tube is pre-folded according to an origami pattern, the failure mode of the tube …
-
Experimental and Predicted Behavior of FRP Beam-Columns Including Retrofitting
… used, namely, channel section, I-section, and square tube section. Six non-retrofitted beam-columns were tested in addition to two retrofitted ones. The members were subjected to an eccentric vertical load applied through a lever arm generating gradually increasing axial load and uniaxial …
-
Design and implementation of an object sensing and counting system
… the objects so that they fall through a small tube in a somewhat single-file fashion. The machine is designed specifically for handling and counting pharmaceutical pills that range in size from 1 to 25 mm. The pills fall through a clear plastic square tube where they are detected and counted by …
-
CFD investigation of cooling flow in a rocket nozzle. A concept for one dimensional modeling with subdomains.
… that the investigations was conducted on were a square tube with a length of 4.2 [m] connected with a inlet manifold and a outlet manifold and 4 other tubes. In order to verify the results a simulation were preformed in the beginning of the thesis that were compared with Volvo Aero’s in-house …
-
Innovative Hybrid FRP/STEEL Splice Details for Modular Bridge Expansion Joints
… have been examined: A GFRP pultruded square tube section, adhesively bonded to the soffit of the spliced beam, consists the moment resisting component in one configuration, whereas the other takes advantage of two series of FRP plates for this purpose. Bolted steel plates splice the …
-
Flow characteristics and acoustic resonance excitation of finned cylinders in cross-flow
… investigated. In the design phase of finned tube heat exchangers, finned cylinders are treated as bare cylinders with a diameter equivalent to their flow blockage. This technique is used in conjunction with empirical data obtained from bare cylinder measurements to estimate the …
-
Torsion as a design driver for structures and architecture
… the intentional deformation of a thin-walled square tube, where each strip of the tube is hinged-joined along its longitudinal edges. The equilibrium geometry of the beam emerges through a delicate interplay between material, its properties, and physical rules within defined boundary …
-
The modelling of particle build up in shell–and–tube heat exchangers due to process cooling water
… high particulate fouling rates inside shell-and-tube heat exchangers that utilize process cooling water. The water and foulants are obtained from various natural and process sources and have irregular fluid properties. The fouling eventually obstructs flow on the shell side of the heat exchanger …
-
Damage Detection in Tubular Structures Using Nonlinear Ultrasonic Guided Waves
… tubular structures, namely circular pipes and square tubes. The main contents of the thesis are outlined as follows: (1) By mixing longitudinal and torsional guided wave modes in the circular isotropic pipe with material nonlinearity, the combinational harmonics at difference frequency with …
-
Tahokov
Řízená deformace. Za jakých podmínek lze ovlivnit proces deformace železa? Tato práce je zaměřena na roztahování ocelových profilů. Pomocí různých zkoušek a testů budu konfrontovat výslednou vizuálnost s technickými možnostmi materiálu. Snaha o nalezení hranice, která je ještě přípustná z hlediska …
-
Static Response of FRP Structural Systems – Piles, Platforms, and Poles
… that included 3/8” angle, ½” angle, 2” x 2” square tube, stiffened bottom with plate were used. Bolt torque levels were varied (0ft-lb, 20ft-lb, and 40ft-lb) to establish joint rigidity and find joint failure under different bolt torques and corresponding load-strain and deflection response …
-
Analytical and experimental investigations of the collapse load characteristics of thin walled structural forms under compressive load actions
… uniform compression of plain and lipped channel, square tube and equal angle sections. In addition to the results of the actual tests, the various auxiliary techniques such as an original application of the Moire fringe method are fully described. The mechanical properties inclusive of tensile and …
-
Kriteria vzniku defektů při ohybu profilových trubek
V práci jsou popsány poznatky z technologie ohybu kruhových trubek, jde o popis konvenčních, ale i nekonvečních zařízení. Jsou zde uvedeny technologické parametry v návaznosti na vznik defektů a výpočtové vztahy pro určení ohybového momentu. Tyto poznatky byly zobecněny a využity k řešení změny …
-
Experimental and Design Evaluation of Multi-bolted GFRP Joints
… study is mainly intended to evaluate doubler and tube-in-tube concepts for their feasibility and effectiveness of multi-bolted joints in composite under different static loading to ensure load/moment transfer and minimize the stress concentration in joints. Experimental and theoretical evaluations …