Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 30 for “"Static eccentricity"”.
-
Analysis of Force Coefficients and Dynamic Pressures for Short-Length (L/D=0.2) Open-Ends Squeeze Film Dampers
… various amplitude (r) and departing from various static eccentricity (es) endeavors to reveal the dynamic performance of SFDs to events in gas turbine engine operation such as a blade loss, or a change in eccentricity. Circular (rX=rY) whirl orbits of the SFD with amplitude r/c=0.05 to 0.71, and …
-
Torsional effects in structures subjected to strong ground motion
… in the seismic response of structures with small static eccentricity and closely spaced frequencies. In order to study the response of structures subjected to complex loading histories, structural models were analyzed through the use of a numerical procedure (Newmark's $\beta$ method) combined …
-
Performance analysis of a 3-phase induction machine with inclined static electricity
… unequal air-gap. So far, work on detection of eccentricity related faults in synchronous and induction machines have been well documented. However, few are reported on faults resulting fiom axial non-uniform air-gap. This thesis investigates the performance of a three-phase induction machine …
-
Performance of a Short Open-End Squeeze Film Damper With Feed Holes: Experimental Analysis of Dynamic Force Coefficients
… amplitudes range from r=0.05c-0.6c, while the static eccentricity ranges from eS=0-0.5c. Analysis of the measured film land pressures evidence that the deep end grooves (provisions for installation of end seals) contribute to the generation of dynamic pressures in an almost purely inertial …
-
Performance of an Open Ends Squeeze Film Damper Operating with Large Amplitude Orbital Motions: Experimental Analysis and Assessment of the Accuracy of the Linearized Force Coefficients Model
… orbit motions at prescribed whirl frequencies. A static loader, 45˚ away from each shaker, pulls the bearing to a static eccentric position. Circular orbit tests were performed (10 – 100 Hz frequency range) for eight increasing orbit amplitudes (r=0.08c to ~0.71c) and under four static …
-
Condition monitoring of high efficiency heating, ventilation and air conditioning systems
… condition monitoring method, which analyzes the static pressure of the fan blade, load torque, and the fan motor speeds. For most air handlers, the unbalanced load of the blower wheel is created by unevenly distributed contaminants on the blades. The traditional current-based condition monitoring …
-
CFD Based Prediction of Rotordynamic Coefficients and Stability Analysis for Centrifugal Pump/Compressor
… impeller, a 3D impeller model with the dynamic eccentricity and the tilting angle is generated and the corresponding rotordynamic coefficients are obtained. The calculated results indicate that the precessing motion increases the tendency towards destabilization of the rotor. Lastly, influence …
-
Finite Element Analysis of Motor Eccentric Forces and Effects on Vibration
… of the sources of machinery vibrations. Motor eccentricity is one of the common phenomena that cause forces exerted on motor and the machinery train. The eccentricity between stator and rotor is almost inevitable. Mass unbalance, shaft bending as well as bearing tolerances can introduce the …
-
Identification of Force Coefficients in Two Squeeze Film Dampers with a Central Groove
… to finally exit to ambient. In operation, a static loader pulls the bearing to various static off center positions with respect to the stationary journal, and electromagnetic shakers (2,200 N) excite the test system with single frequency loads over a frequency range to generate rectilinear, …
-
Housing Shape's Impact on Electric Submersible Pump's Equilibrium Position and Rotordynamics
… of the rotor with respect to the housing is the Static Equilibrium Position (SEP). The SEP is important in determining the rotordynamic coefficients for the bearings/seals. An SEP analysis suitable for ESPs is shown. The analysis predicts the equilibrium position due to gravity and/or curvature …
-
Investigation of non-linear phenomena in rotor-damper assemblies
… and then two squeeze-film dampers with different static misalignments were studied. Non-linear jump phenomena and subharmonic resonances have been demonstrated both experimentally and theoretically for a range of rotor unbalance. The effects of varying oil supply have been demonstrated. …
-
System-Level Rotordynamic Analysis of Centrifugal Compressors Using Computational Fluid Dynamics (CFD), Design and Optimization of Novel Swirl Brakes
… CFD approaches, namely quasi-steady, transient static eccentricity, and transient mesh deformation techniques are studied and benchmarked against analytical and experimental results from the literature. Having established the efficacy of the proposed approach, 4 types of swirl brakes are …
-
Optimum design of earthquake resistant structures implementing computational methods
… effect caused by mass, stiffness or strength eccentricity. Due to this type of asymmetry torsional moments are generated that are imposed by means of additional shear forces developed at the vertical resisting structural elements of the buildings. Although the torsional effect on the response …
-
On-line condition monitoring and detection of stator and rotor faults in induction motors.
… and rotor faults (i.e. shorted turn faults, eccentricity faults, and broken rotor bar faults) using three types of sensor signals (i.e. current, leakage flux, and vibration) under different loading conditions. The work is based on an extensive series of sensor measurements taken using a …
-
Measured and predicted rotordynamic coefficients and static performance of a rocker-pivot, tilt pad bearing in load-on-pad and load-between-pad configurations
This thesis presents the static and dynamic performance data for a 5 pad tilting pad bearing in both the load-on-pad (LOP) and the load-between-pad (LBP) configurations over a variety of different loads and speeds. The bearing tested was an Orion Advantage with direct lubrication exhibiting these …
-
Fault detection and identification in Permanent Magnet Synchronous Machines
… Synchronous Machines are discussed in this work: static eccentricity, partial demagnetization and turn-to-turn short circuit faults. Finite Element Analysis simulations and experimental testes were carried out for three Permanent Magnet Synchronous Machines under healthy and the faulted …
-
Measured Static and Rotordynamic Characteristics of a Circumferentially-grooved-stator/smooth-rotor Liquid Annular Seal: Influence of Viscosity, Eccentricity, Pressure, and Speed
… differential pressure (?P), rotor speed (?), and static eccentricity (?o) were varied. Tests are conducted to determine how static and rotordynamic characteristics of a CGS are affected by ? changes. The measured results are compared to predictions, and a smooth seal when applicable. Testing was …
-
Design, analyses and experimental study of a foil gas bearing with compression springs as a compliance support
… nonlinear and showed different behavior for static loading and the sinusoidal dynamic loading. The measured equivalent viscous damping coefficients increased with the applied load amplitude. A series of parametric design studies were performed to investigate the effects of various design …
-
High Force Density Linear Electromagnetic Actuators for Active Suspension
… magnetic force (UMF) in a magnetic screw under static eccentricity have been investigated analytically and by a full 3-D FE model with high-quality meshes. It is shown that the impact of UMF on the mechanical design and the resultant increase in bearing friction are not significant. Finally, the …
-
Detection of faults in a scaled down doubly-fed induction generator using advanced signal processing techniques.
… short-circuit faults (ITSCF), rotor ITSCF and static eccentricity (SE) faults in the laboratory environment. The micromachine has been assessed under the healthy and faulty states, both before and after incorporating a converter into the rotor circuit of the machine. In each scenario, the fault …
Page 1 of 2