Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 225 for “"Steam injection"”.
-
Recovery of viscous crude oil by steam injection
… they proved to be uneconomical. Propane-Butane injection followed by water resulted only in loss of the expensive injected fluid. Many things could have happened to the liquid petroleum gas, but the probabilities are that it was dissolved in the undersaturated crude oil, or perhaps that it …
-
Optimization of cyclic steam injection using geometric programming
Includes bibliographical references.
-
Experimental investigation of caustic steam injection for heavy oils
… has been conducted to compare the effect of steam injection and caustic steam injection in improving the recovery of San Ardo and Duri heavy oils. A 67 cm long x 7.4 cm O.D (outer diameter), steel injection cell is used in the study. Six thermocouples are placed at specific distances in the …
-
Steam injection for globule size reduction in an emulsion
Thesis (Ph. D.)--Michigan State University of Agriculture and Applied Science. Department of Agricultural Engineering, 1962
-
Relative Permeability Determination for Steam Injection Processes: An Analytical Approach
… is achieved through the utilization of steam assisted gravity drainage (SAGD) as well as solvent steam assisted gravity drainage (S-SAGD). However, the presence of three distinct fluid phases (oil, steam, and water) in the reservoir during steam injection has implications for the …
-
Response of mat conditions and flakeboard properties to steam- injection variables
… in three locations for one conventional and four steam-injection press schedules used in the laboratory scale manufacture of aspen (Populus grandidentata and Populus tremuloides) flakeboard. Two resins, phenol formaldehyde and polymeric MDI, were used. Steam-injection press schedules varied from …
-
New Dual Porosity Thermal Simulator for Steam Injection in Naturally Fractured Reservoirs
… recovery from naturally fractured reservoirs is steam injection. Heat transfer, imbibition, gas generation, and other mechanisms have the potential to expel fluids from matrix blocks at sufficient rates and in sufficient quantities to be feasible. The objective of this study is to develop an …
-
Performance Evaluation of Solvent Assisted-Steam Injection Processes with Asphaltene Insoluble Solvents
Adding solvents to steam flooding processes during bitumen production can reduce the water and natural gas usage but may create a new unique set of problems. Most solvents are toxic and are prohibited to be used on sites. Most importantly, since the solvent-bitumen-steam interactions are not well …
-
The effect of steam injection on the electrical conductivity of sand and clay
… electrical surveys used to monitor subsurface steam-injection projects, one needs to know whether steam zones are resistive or conductive relative to initial conditions. This can be determined through laboratory measurements of the effects of steam injection on the electrical conductivity of …
-
Evaluation of UHT milk processed by direct steam injection and steam infusion technology
UHT direct steam injection and steam infusion are widely used; however there is no comparison of their impact on milk components. This study evaluates the structural changes at different steps during the UHT processing of whole milk in a full-scale UHT plant by transmission electron microscopy …
-
Steam Injection Strategies for Bitumen Recovery from an Element of the Grosmont Carbonate Reservoir
… study employs numerical simulation for several steam-based recovery schemes and proposes steam injection strategies. Selected simulation results were analyzed using analytical methods. A representative geological model of Grosmont was used to examine numerically several steam injection schemes, …
-
A comparative analysis of numerical simulation and analytical modeling of horizontal well cyclic steam injection
… research is to compare the performance of cyclic steam injection using horizontal wells based on the analytical model developed by Gunadi against that based on numerical simulation. For comparison, a common reservoir model was used. The reservoir model measured 330 ft long by 330 ft wide by 120 ft …
-
Steam injection distribution optimization in SAGD oil field using reinforcement learning and web-based GIS
Steam injection distribution optimization refers to the process of distributing certain amount of high temperature steam in steam-assisted gravity drainage (SAGD) oil field to maximize the total oil production. In this thesis, two novel optimization methods are presented to solve the steam …
-
Performance and emission characteristics of natural gas combined cycle power generation system with steam injection and oxyfuel combustion.
… oxidizes with air and pure oxygen separately. Steam is injected in main combustion chamber and reheater combustion chamber individually and simultaneously to understand the performance of combined cycle work output and greenhouse gas emission. The effect of pressure ratio, turbine inlet …
Page 1 of 12