Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 91 for “"Stiction"”.
-
Oil stiction in automatic compressor valves
… and theoretical investigations into oil stiction effects in automatic compressor valves. The experimental programme involved the testing of disc valves in a compressor in which the working fluid could be varied and the oil circulation controlled. The main purpose of the experiment was to …
-
Stochastic multiscale modeling of MEMS stiction failure
… and van der Waal forces, can lead to the stiction failure for which the two contacting surfaces can accidentally be stuck together permanently. This is a common failure of MEMS. Because of the comparability between the roughness of the contacting surfaces and the ranges of adhesive stress, …
-
Stiction Prevention in MEMS Structures After Wet Treatment by Optimized Drying Techniques
… we use liquid chemicals, which may result in stiction of suspended structures. Thus, the drying process is being an essential step in wet processing. If we do not have a proper technique to evaporate liquid inside structures, stiction would be unavoidable and may cause failure in fabricated …
-
Mode I and Mode II Measurements For Stiction Failed Micro-Electro-Mechanical Systems
… (MEMS), the most common type of failure is stiction. Stiction is the unintended adhesion between two surfaces when they are in close proximity to each other. Various studies have been conducted in recent years to study stiction. Our research group has shown the in-service repair of the …
-
Wettability modification of polysilicon for stiction reduction in silicon based micro-electromechanical structures
… in the fabrication of such structures is "stiction" or adhesion to the substrate. This may occur during the drying step that is required after wet processing and/or during use of a device. Deposition of self-assembled monolayer coatings is one of the most successful approaches to chemical …
-
Anti-Stiction And Self-Recovery Active Mechanisms For High Reliability RF-MEMS Switches
… the actuation electrode, also referred to as stiction, due to accumulated charge or to micro-welding phenomenon, are the most common types of RF-MEMS failures. This work presents a novel effective heat-based mechanism that enables to release a stuck component. Such mechanism can be embedded …
-
Mechanics of nanoscale beams in liquid electrolytes: beam deflections, pull-in instability, and stiction
… is approximately equal in liquid and air. Stiction, the most common failure mode of the cantilever-based devices, is studied in a liquid environment, including elastic energy, electrochemical work done, van der Waals work done and surface adhesion energy. We extend the classical energy …
-
Neural Network-Based Noise Suppressor and Predictor for Quantifying Valve Stiction in Oscillatory Control Loops
Valve stiction-induced oscillations in chemical processing systems adversely affects control loop performance and can degrade the quality of products. Estimating the degree of stiction in a valve is a crucial step in compensating for the effect. This work proposes a neural network approach to …
-
Curve veering and a parametric study of stiction in capacitive microelectromechanical systems subjected to electrostatic and Casimir forces
Curve veering is a phenomenon in which the plot of eigenvalues of a system against a system parameter sometimes results in curves that abruptly veer away from each other in a rapid but continuous manner at points where they are expected to intersect. For certain modes of vibration, the natural …
-
Characterization of Mechanical Properties at the Micro/Nano Scale: Stiction Failure of MEMS, High-Frequency Michelson Interferometry and Carbon NanoFibers
… NanoElectroMechanical Systems (NEMS) - a.k.a. stiction-failure. The adhesive forces between MEMS devices leading to stiction failure are characterized in this dissertation analytically and experimentally. Specifically, the adhesion energy of poly-Si μcantilevers are determined experimentally …
-
Continuous high-speed resin 3D printing by interface temperature control : a thesis presented in partial fulfilment of the requirements for the degree of Master of Engineering in Mechatronics at Massey University, Albany, New Zealand. EMBARGOED until 15th December 2027
… their printing speed is often limited by the stiction between the cured resin and the substrate. This stiction restricts how quickly layers can be separated during the printing process and is one of the key limitations preventing the wider adoption of high-speed and continuous 3D printing. …
-
Accelerated aging of the digital micromirror device using full custom electrostatic control
Stiction and friction are integral to the dynamic operation of many Microelectromechanical(MEMS) and a comprehensive approach is needed to develop surface coating systems that take into account the fabrication, packaging and operational parameters. The operating environment is also vital for device …
-
Study of chemical contamination at head/disk interface
… at head/disk interface (HDI) in the term of stiction, fly stiction, head smear and disk wear and investigated the failure mechanisms. Hydrocarbon could induce high stiction or fly station at HDI. However, slidersa?? flying characteristics played an important role in leading to interface …
-
Detecção e diagnostico de agarramento em válvulas posicionadoras
Valve stiction, or static friction, in control loops is a common problem in modern industrial processes. Recently, many studies have been developed to understand, reproduce and detect such problem, but quantification still remains a challenge. Since the valve position (mv) is normally unknown in an …
-
Design And Characterization Of Nanoelectromechanical Switches
… show that NEM switches are vulnerable to stiction. Using smart geometry and electrode configurations it is possible to overcome stiction at the expense of a more complex design and higher pull-in voltage. Finally a memory element and electric field sensor are discussed as promising …
-
Nano-patterned Si structures for optical filters and electro-mechanical relays: Fabrication, characterization, prospects, and limitations
… several failure mechanisms including stiction in the contact area, and arc-discharge leading to contact degradation and even contact welding limit their operational lifetime. In this thesis, a method for measuring stiction force is presented using in-plane electrostatically actuated Si …
-
Improving Contouring Accuracy in CNC Machines
… reduced by feedforward compensation. A two-stage stiction compensation scheme is proposed to reduce or eliminate the contour errors caused by stiction. A model-based Taylor series expansion error compensation (TSEEC) approach formulates the contour error as a Taylor series expansion around points …
-
Modelling tribology of slider and disk in a computer hard drive system
… loss and allow higher areal density. Friction, stiction and wear between the slider and disk in a hard drive were studied using Accelerated Friction Test (AFT) apparatus. Contact Start Stop (CSS) and constant speed drag tests were performed using commercial rigid disks and two different air …
-
Innovative techniques for industrial process modeling and monitoring
… tuning or equipment problems. Among them, valve stiction is one of the most common equipment problems. Although there has been many attempts to understand and model valve stiction, those models are either physical models which are not practical to use, or empirical models but with rather …
-
LASER-INDUCED MICROTEXTURING OF MAGNETIC RECORDING MEDIA
… and laser pulse duration. Considering that the stiction is proportional to the contact area, we tried to reduce and optimize the actual contact area between the head slider and the hard disk surface by reducing the bump size and bump density. The mechanisms responsible for the bump formation …
Page 1 of 5