Global ETD Search

Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.

Results

Showing 1 to 13 of 13 for “"Straightener"”.

  1. Testing of an Axial Flow Moisture Separator in a Turbocharger System for Polymer Electrolyte Membrane Fuel Cells

    … separator was tested independently, with a flow straightener preceding it, and with a commercially available centrifugal moisture separator in series following it. It was shown that cooling makes a significant impact on the separation rate while adding a flow straightener does not. Separation …

    gatech Repository record for Testing of an Axial Flow Moisture Separator in a Turbocharger System for Polymer Electrolyte Membrane Fuel Cells (opens in a new tab)

  2. A Study of the Beginning Boundary Layer Influence on the Flow Field about a Two-Dimensional Automotive Model

    … disturbance created by the step where the flow straightener and screens mount to the inlet of the wind tunnel. The model data from the test section and splitter plate showed an increase in velocity across the top of the model when placed on the splitter plate that can be partially attributed to …

    ut-knoxville Repository record for A Study of the Beginning Boundary Layer Influence on the Flow Field about a Two-Dimensional Automotive Model (opens in a new tab)

  3. CFD modeling of center cones, vortex breakers and pressure relief slits in a wind speed accelerator.

    … concentrator components were tested: a flow straightener, vortex breaker, and pressure relief slits. Fluent 12.1, a computational fluid dynamics (CFD) program, was used to model air flow patterns through a prototype wind concentrator and optimize its performance. Through this method, it was …

    louisville Repository record for CFD modeling of center cones, vortex breakers and pressure relief slits in a wind speed accelerator. (opens in a new tab)

  4. Playing Kazoo: Scales

    … a sort of supernatural peacekeeper and straightener of mystical messes, has to find out who did it. April's quite insistent about it. Being dead will do that to a person. Not that Roger's in the mood. He's just killed his favorite god, and dealing with a murder that could wind up being …

    iastate Repository record for Playing Kazoo: Scales (opens in a new tab)

  5. Correlation for measured mold heat flux and CON1D simulations for feasible operating conditions in thin-slab continuous casting

    … First, controlling metallurgical length between straightener and end of containment to avoid stress related cracks and whales respectively; Secondly, to regulate surface temperature profile to avoid unbending in the temperature range of the ductility trough. In this work, using the heat-transfer …

    uiuc Repository record for Correlation for measured mold heat flux and CON1D simulations for feasible operating conditions in thin-slab continuous casting (opens in a new tab)

  6. Environmental influences on menstrual disturbances and uterine leiomyomata

    … socioeconomic environment, use of chemical hair straighteners, and metal biomarkers — on the risk of abnormal uterine bleeding (AUB), dysmenorrhea, and uterine leiomyomata (UL).First, we conducted a cross-sectional study of the associations of neighborhood socioeconomic disadvantage with the …

    bu Repository record for Environmental influences on menstrual disturbances and uterine leiomyomata (opens in a new tab)

  7. Design and Low-Speed Validation of a Tailored Low-Loss Flow Straightening Device

    In many applications, non-uniform flows are undesirable and have a negative system impact. Non-uniform flows can arise in many ways such as in geometry changes and turns in piping/ducting, as well as with lip separation in certain aircraft engine inlets at high angle of attack. These …

    vt Repository record for Design and Low-Speed Validation of a Tailored Low-Loss Flow Straightening Device (opens in a new tab)

  8. Design, Construction, and Qualification of an Open Loop Wind Tunnel Facility to Quantify Enhanced Heat Transfer/Pumping Power Performance in Isothermal Rectangular-Cross Section Passages

    … cm tall and 23.2 cm wide test section, a flow straightener/exit plenum, round ducting, a flow rate measurement nozzle, and finally the suction end of a variable speed blower. The upper and lower test section surfaces consist of aluminum blocks that are separated from each other by insulation. …

    unr Repository record for Design, Construction, and Qualification of an Open Loop Wind Tunnel Facility to Quantify Enhanced Heat Transfer/Pumping Power Performance in Isothermal Rectangular-Cross Section Passages (opens in a new tab)

  9. Rovnačka profilů

    Diplomová práce se zabývá návrhem rovnačky profilů, která je určena pro rovnání U, I a L profilů za jejich pohybu. Zařízení je součástí válcovací tratě, kde slouží pro dokončovací operaci – rovnání profilů. Součástí práce jsou návrh konstrukční varianty, návrhové a kontrolní výpočty, popis funkce …

    brno-tech Repository record for Rovnačka profilů (opens in a new tab)

  10. Technologie rovnání polotovarů

    Tématem bakalářské práce je vytvoření všeobecného přehledu postupů pro rovnání polotovarů, a to jak za pomoci metod ručních, tak i strojních. Práce podává informace o principech této technologie, zabývá se ukázkami použití a předkládá výčet výhod a nevýhod daných postupů na základě průzkumu …

    brno-tech Repository record for Technologie rovnání polotovarů (opens in a new tab)

  11. Návrh rovnačky XRK 7-200

    Diplomová práce Návrh rovnačky XRK 7-200 seznamuje čtenáře s typy rovnacích strojů a jejich principy. Následně jsou popsány postupy konstrukčního návrhu sedmiválcové rovnačky pro průměry tyčí 100-200 mm. Návrh se týká především horního a dolního příčníku. Práce též popisuje vybrané výpočty, a to …

    brno-tech Repository record for Návrh rovnačky XRK 7-200 (opens in a new tab)

  12. Výpočtová analýza kosoúhlého rovnání tyčí

    V dnešní době je na výrobky z hlediska kvality kladen stále větší důraz. Tato práce se zaměřuje na analýzu rovnání dlouhých polotovarů s kruhovým průřezem na kosoúhlých rovnačkách. Tento proces zvyšuje jakost polotovarů z hlediska jejich křivosti, protože tyto polotovary nedosahují po prvotním …

    brno-tech Repository record for Výpočtová analýza kosoúhlého rovnání tyčí (opens in a new tab)

  13. Uložení spodních, horních a průhybových válců rovnačky XRK 7-200

    Bakalářská práce Uložení spodních, horních a průhybových válců rovnačky XRK 7-200 popisuje postupy konstrukčních návrhů válců sedmiválcové rovnačky tyčí o průměru 100-200 mm. Zároveň se zabývá kontrolou tohoto návrhu. Ta spočívá ve výpočtu životnosti ložisek a kontrolou pevnosti hřídelí.

    brno-tech Repository record for Uložení spodních, horních a průhybových válců rovnačky XRK 7-200 (opens in a new tab)