Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 74 for “"Stress concentration factor"”.
-
Torsional stress concentration factor for hollow stepped shafts
In this investigation the stress concentration factor was evaluated for a hollow stepped shaft with variable wall thickness and two fillet sizes. Electric strain gages of the SR-4 type were employed to measure strains in the fillet section. Values of the stress concentration factor were determined …
-
Prediction of Stress Concentration Factor from In-Line Inspection Data Using Convolutional Neural Networks
… to identify dent defects and calculate their stress concentration factor (SCF). These ILI runs typically identify a large number of dent defects, making it difficult for engineers to process individually. This study developed a Convolutional Neural Network (CNN) trained on 4,667 raw ILI data …
-
Determination of stress concentration factors using experimental methods
Several experimental methods are examined for stress concentration factor determination. Tests are performed on a chosen 2-D specimen using strain gages, brittle coating, brittle specimen failure, photoelasticity, and Moire interferometry. Results are compared to each other and to finite element …
-
Stress concentrations in undercut spur gear teeth via the finite element method
… analysis of the influence of undercutting on the stress concentration factor for undercut gears using the finite element method is presented. The models used are in the shape of a whole gear with three teeth. The middle tooth is loaded assuming single-tooth contact. Thirty seven finite element …
-
Transient thermal stresses at near surface elliptical holes
… of the near surface elliptical holes on the stress field when the surface experiences a rapid temperature change. The problem is formulated as a two-dimensional transient problem in a multiply connected semi-infinite region. It is assumed that the quasi-static formulation of thermoelasticity …
-
Fatigue Performance of Brass Light Pole Couplings
… and individual loading configurations. The stress concentration factor, Ktb, determined by strain measurement at hexagonal and notched sections was 5.70, which is slightly higher than the theoretical stress concentration factor of 4.7. Fatigue tests were also performed on the notched …
-
A finite element analysis of pinion shaped spur gear teeth
… with a pinion cutter upon the geometry and root stresses in external spur gears using the finite element method is given. The models analyzed have the shape of a ring with three teeth. The middle tooth is loaded and load sharing has been assumed. Thirty-five finite element models were used for …
-
The effects of water displacing corrosion preventatives on the fatigue behaviour of mechanically fastened aluminium joints
… in friction coefficient. Three types of stress reduction factors are proposed in the net-section failure model to account for these parameters. The stress reduction factors modify stress range that is used in crack growth calculation. If there are no effects of these parameters, the …
-
Concentração de tensões em chapas infinitas tracionadas
… work presents a theoretical development about stress concentration in infinite plates with holes, using complex variables functions. Applications of this technique to different problems are presented as well as the soluction of the same problems using Finite Element Method. Through results …
-
Stress concentration in fibrous composite material
This thesis work involves an initial study on Stress Concentration caused by holes out of center in thin plates of finite width made of Unidirectional and Crossply Fiberglass Composites. The results are reported under the form of the Stress Concentration factor K. as a function of two …
-
A Comparative Study of the Effects of Stress Raisers in Steel Specimens on Fatigue Life in Bending
One of the primary areas of experimental stress analysis for the last century has been the determination of theoretical stress concentration factors for different combinations of holes and notches on samples under static loading (tension and compression). Although the values for the theoretical …
-
Stress reduction in a plate with a hole by applied induced strains
This work investigates the potential of reducing stresses in the region of stress concentration by applied induced strains. A thin 30 inch square plate with a 1 inch diameter circular hole under uniaxial load was used for this investigation. This investigation considered first an ideal case with a …
-
Isogeometric Finite Element Code Development for Analysis of Composite Structures
… diminishing property of Nurbs basis for stress analysis of composite and sandwich beams and plates. This research also computes stress concentration factor in a composite plate with a hole. Isogeometric nonlinear/linear finite element code is developed for static and dynamic analysis of …
-
Stresses in sprayed concrete tunnel junctions
… comparatively little work has been done on the stresses in SCL tunnels or junctions. The structural behaviour of an SCL tunnel junction in terms of stresses is not well understood because design models are usually simplistic and field data are scarce. This research addressed these gaps in …
-
ΠΡΟΣΔΙΟΡΙΣΜΟΣ ΤΩΝ ΓΕΩΜΕΤΡΙΚΩΝ ΜΕΓΕΘΩΝ ΠΟΥ ΟΡΙΟΘΕΤΟΥΝ ΤΗΝ ΑΝΤΟΧΗ ΣΕ ΚΑΜΨΗ ΤΩΝ ΔΟΝΤΙΩΝ ΟΔΟΝΤΩΤΩΝ ΤΡΟΧΩΝ
PRESUPOSITION FOR THE CALCULATION OF BENDING STRESSES ON THE GEAR TEETH ROOT, IS THE KNOWLEDGE OF THE TOOTH PROFILE WHICH, SHOULD BE NOTED, IS DIFFERENT FOR GEARS WITH DIFFERENT NUMBER OF TEETH. OWING TO THE RESEARCH DEVELOPED IN THIS DISSERTATION IT WAS SUCCEEDED: A) TO DERIVE EQUATIONS WHICH GIVE …
-
The development of design criteria for a rotating disk containing noncentral circular hole patterns
The problem of finding the stress distribution about circular, noncentral holes in a spinning disk is discussed. A theoretical approximation is first developed using the methods of elasticity and combining solutions to similar problems from Ling (reference 6) and Timoshenko and Goodier (reference …
-
A finite element mesh optimization procedure using a thermal expansion analogy
… In one test case, the errors in the maximum stresses are reduced by more than 1/3 after 1 iteration. In another test case, the error in the stress concentration factor is reduced by more than 3/4 after 7 iterations.
-
A simplified method for the photoelastic determination of stress concentration factors in a tensile stress field
The stress concentration factors for rectangular slots with semicircular ends with their major axes inclined to the direction of a uniaxial tension field were investigated by photoelastic methods. A major portion of this thesis deals with the problem of loading a circular disk such as to create an …
-
An Investigation of Hole Size Effects in a Composite Material During Tensile Fracture
… with an increase in hole size at a constant stress concentration factor, for a glass fiber reinforced epoxy crossply laminate during tensile fracture. The characteristic dimension according to the point-stress and average-stress criteria of the two-parameter models proposed by Whitney and …
Page 1 of 4