Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 15 of 15 for “"Sub 1V"”.
-
A simple sub-1V voltage reference
A traditional bandgap reference voltage has a value approximately equal to 1.2V. This is an inconvenient value to obtain in short-channel CMOS circuits where the nominal power supply voltage is 1.2V or lower. Here, a simple circuit is presented to generate a reference voltage between 600mV and …
-
Design of continuous-time sigma-delta modulators with inverter-based amplifiers for sub-1V applications
… (OTAs). This thesis presents the development of sub-1V continuous-time sigma-delta modulators (CT-SDMs) with inverterbased amplifiers. The state of the art of CT-SDMs with inverter-based amplifiers has been delimited, and two low-voltage CT-SDMs prototypes have been designed and experimentally …
-
A 0.45 V low power high PSRR subthreshold CMOS voltage reference
… low power requirement is to operate MOSFETs in subthreshold region. Most often, forward biased PN-junctions of BGRs are substituted with MOSFETs biased in the subthreshold region and achieves a supply voltage down to 0.6 V.\par This paper presents a sub-1V voltage reference circuit that has only …
-
Power Delivery and Management in 3D-Stacked Systems with Back-End-of-Line Compatible Oxide Channel Transistors
… network inference workloads targeting 3.3V-to-sub-1V conversion. Beyond the 3.3 V input, high-voltage operation is addressed for heterogeneous 3D (H3D) systems, where amorphous tungsten-doped indium oxide (IWO) power transistors with gate-to-drain offset regions and a cascaded hybrid DC-DC …
-
Efficiency improvement in nanometre CMOS outphasing power amplifiers
… PAs suffer from low output power due to the sub-1V supply voltages and lossy passive components. This thesis focuses on improving the design of CMOS outphasing PAs which utilise unisolated power combiners and switched-mode voltage-source PA stages.<br/><br/>Power combiner design is advanced …
-
Circuit modeling and design techniques for efficient power delivery under resonant supply noise
… one of the main performance limiting factors in sub-1V technologies. Resonant supply noise caused by the package/bonding inductance and on-die capacitance has been reported as the dominant supply noise component in high performance microprocessors. Recently, adaptive clocking schemes have been …
-
MOSFET Current Source Gate Drivers and Topologies for High Efficiency and High Frequency Voltage Regulator Modules
… microprocessors follow the trend of decreasing (sub 1V) while the demanding currents increase (higher than 100A). Furthermore, the high slew rates during the transient will reach 1200 A/us. All these impose a serious challenge on a Voltage Regulator (VR) or Voltage Regulator Module (VRM). In …
-
Multiphase Hybrid Switched-Capacitor Buck Converters: Synthesis, Packaging, Modelling, and Control for HPC Applications
… manufacturing and lithography—are operating at sub-1V core voltages. This creates a challenging power conversion gap. Unfortunately, conventional multiphase buck (CMB) converters—widely used for 12V-to-1V regulation—are unsuitable for direct 48V-to-sub-1V conversion while meeting stringent …
-
Bandgap Reference Design at the 14-Nanometer FinFET Node
… process parameters are exponentially affected in subthreshold conduction. In order for this proposed solution to be feasible, a design methodology was introduced to mitigate the effects of process variation. A 14 nm bandgap reference was created and simulated across Monte Carlo perturbations for …
-
Sub-10nm Transistors for Low Power Computing: Tunnel FETs and Negative Capacitance FETs
… distributed carriers, which does not allow subthreshold swing (SS) lower than 60mV/dec at room temperature. Recently, a new class of steep-slope devices like Tunnel FETs (TFETs) and Negative-Capacitance FETs (NCFETs) have garnered intense interest due to their ability to surpass the 60mV/dec …
-
Design of Low Power Integrated Radios
… noise figure and power consumption problems of sub 1V mixers. The figure of merit (FOM) is 10 dB higher and the power consumption is 194 μW which is 0.5X lower than the state of the art. The local oscillator (LO) power used is only -14 dBm. Next, a 0.7V 2.3-2.5GHz ultra low power low noise …
-
Κυκλώματα υψηλών συχνοτήτων για σύστημα υπερ-ευρείας ζώνης με διαμόρφωση συχνότητας FM-UWB
… is important as well. The supply voltage of 1V was selected for the FM-UWB transmitter in order to become competitive against other recent published implementations. Targeting at the biasing of the loop divider and the charge pump at the low supply voltage of 1V, a Sub-1V voltage reference …
-
High Frequency, High Efficiency Two-Stage Approach for Future Microprocessors
… efficient way, and accurately regulating the sub-1V voltage in very fast dynamic transient response conditions. Furthermore, the VRs are limited in a given area and the power density is important to save the precious real estate of the motherboard. Based on the power delivery path model, the …
-
Design of PVT Tolerant Inverter Based Circuits for Low Supply Voltages
… the maximum frequency while drawing 4.2mA from 1.1V supply. The measured intermodulation distortion varies by 5dB across 120C variation in temperature and 6.5dB across a 200mV variation in power supply. Further this filter presents a high impedance node at the input and a low impedance node at the …
-
High Frequency High-Efficiency Voltage Regulators for Future Microprocessors
… microprocessors will run at very low voltage (sub 1V), and will consume up to 150A of current, and will have dynamics of about 400A/us. The current VR solution is the 12V-input multiphase interleaved buck converter. The switching frequency is around 300KHz. This approach has several limitations …