Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 18 of 18 for “"Tee Junction"”.
-
Venturi Flowmeter Performance Installed Downstream of the Branch of a Tee Junction
… this research was to evaluate the influence of a tee junction on flow rate measurement of a Venturi flowmeter installed downstream of the branch of a tee. Accuracy in flow measurement is important to organizations where miscalculated flow rates can add up to be millions of dollars in either lost …
-
Classical Venturi Meter Performance Downstream of the Through Leg of a Tee Junction
… installed downstream of the through leg of a tee junction. A flowmeter that functions inaccurately due to improper installation may cause revenue loss for any company or organization involved in extraction, transportation, production, or purchasing of fluid resources and products. This …
-
Two-phase flow and pressure drop in a horizontal, equal-sided combining tee junction
… losses during two-phase flow in combining tee junctions. Pipe networks in industrial applications involve combining and dividing junctions and knowledge of the pressure losses at these junctions is essential for analysis of the flow distribution in the network. To this end, the pressure …
-
Two-phase flow in a mini-size impacting tee junction with a rectangular cross-section
… phenomena in a mini-size, horizontal impacting tee junction. The test section was machined in an acrylic block with a rectangular cross-section of 1.87-mm height × 20-mm width on the inlet and outlet sides. Air-water mixtures at 200 kPa (abs) and room temperature were used as the test fluids. …
-
Venturi Meter Performance When Installed on the Branch of a Tee Junction with Converging Run Flow
… installed downstream of disturbances such as a tee junction, valve, or elbow. In such a case, a laboratory calibration may be needed to measure the Venturi meter’s performance under said limitations so that accurate metering is achieved. However, in some cases, laboratory calibration may not be …
-
Two-phase pressure drop and phase distribution at a reduced horizontal tee junction, the effect of system pressure
… data for air-water flows in a reduced horizontal tee junction. This junction consisted of a 38.1-mm I.D. inlet tube with a 7.85-mm I.D. branch tube, thus yielding a diameter ratio of $\rm D\sb3/D\sb1=0.206.$ The operating conditions were as follows: an inlet* pressure of 3.0 bar (abs), an inlet …
-
Phase redistribution and separation of gas-liquid flows in an equal-sided impacting tee junction with a horizontal inlet and inclined outlets
… flow splitting at an equal-sided impacting tee junction with a horizontal inlet and inclined outlets. The flow loop incorporated a tee junction machined in an acrylic block with the three sided having an equal diameter of 13.5 ± 0.1 mm I.D. Both sets of experiments were conducted at a …
-
Design and assessment of a new device for gas-liquid separation
… was conducted with a combined impacting tee junction in order to study its phase-separation capability for air-water two-phase flows. The combined junction consisted of one horizontal and two vertical impacting tee junctions; all equal-sided with internal diameter 13.5-mm. All experiments …
-
Investigation and design of novel spatial power combiner
… 40% gain bandwidth at 5GHz centre frequency. The Tee-junction coupler in Design 1 is subsequently modified and the final bandwidth is increased to 52%. To achieve a greater performance, the direct signal coupling technique and the EBG hole structure are proposed and verified through the …
-
Two-phase flow in horizontal impacting tee junctions, current state of the art
… the phase distribution in horizontal impacting tee junctions during two-phase flow. The currently existing data base was reviewed and the effects of different parameters on the phase distribution were investigated. These parameters include JL1, JG1, P1, x1, inlet flow regime, and inlet …
-
Experimental investigation of gas-liquid separation with a new combined impacting junction
A novel system of combined impacting tee junctions was designed to generate partial- and full-phase-separation data for air-water two phase flow. The system consisted of three horizontal and four vertical equal-sided impacting tee junctions of internal diameter 13.5 mm, having one (horizontal) …
-
Mixing gaseous hydrogen into natural gas distribution pipelines
… trapped near the top wall once injected via a Tee junction. In this study, the hydrogen blending into the natural gas distribution pipelines using Tee junctions is numerically investigated, and the mixing homogeneity (uniformity) length is quantified through the coefficient of variation (CoV) …
-
Design and applications of improved hyphenation and separation strategies for multidimensional biomolecule characterization
… The interface uses a tapered stainless steel needle that surrounds the capillary terminus, so that the needle interior acts as the CE outlet vial and the outside tip is the electrospray emitter. A chemical modifier solution, introduced via a tee junction, serves to improve the …
-
Three Dimensional Finite Element Analysis of the IDDP-2 Modulating Orifice Control Valve
… area of the valve body is the PN160 flange, the Tee junction, and its internal weld layers, where constrained thermal expansion and material mismatch cause high stress. Although membrane stresses in the constrained flange region exceed the nominal design limits specified in EN 12516-2, the …
-
Numerické modelování soutoku proudu v rozvětvení tvaru T.
Hlavním cílem této diplomové práce je provedení numerického modelování soutoku proudů v rozvětvení tvaru T pomocí programu Fluent. Modelování je provedeno pro různé poměry průtoků při stacionárním proudění. Z výpočtů jsou, s využitím nového matematického modelu, vyhodnoceny křivky ztrátových …