Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 27 for “"Torque converter"”.
-
Modelling and measurement of transient torque converter characteristics
The torque converter is a crucial component in the drivetrain of a vehicle equipped with an automatic gearbox. It has the ability to transfer power with torque amplification, allow slip between engine and transmission and dampen vibrations between the two. For these reasons its characteristics will …
-
Transient behavior of an engine-torque converter-load system
Thesis (M.S.)--Michigan State University. Dept. of Agricultural Engineering, 1966
-
Transient Maneuvers and Pressure Analysis on an Automotive Torque Converter
… of internal fluid behavior of an automotive torque converter in a front-wheel drive automatic 6-speed transmission. The fluid behavior is identified through 29 pressure transducers instrumented throughout the torus, acquired through IR Telemetrics multiplexed channels, and analyzed with …
-
DEVELOPMENT OF A DYNAMIC TORSIONAL ACTUATOR FOR TORQUE CONVERTER CLUTCH CHARACTERIZATION
… of testing damping and isolation capabilities of torque converter clutch assemblies in automotive torque converters. By utilizing an electric motor typically found in hybrid electric vehicles, the desired torque fluctuations can be achieved for these measurements. The electric motor can be used as …
-
Torque converter turbine noise and cavitation noise over varying speed ratio
… the operational noise caused by automotive torque converters during speed ratio operation. Two specific cases of torque converter noise will be studied; cavitation, and a monotonic turbine induced noise. Cavitation occurs at or near stall, or zero turbine speed. The bubbles produced due to …
-
Experimental investigation of the flow field in an automotive torque converter
Thesis (M.S.)--Michigan State University. Department of Mechanical Engineering, 1993
-
PRESSURE MEASUREMENTS INSIDE MULTIPLE CAVITIES OF A TORQUE CONVERTER AND CFD CORRELATION
A torque converter was instrumented with 29 pressure transducers. The pressure transducers were located in multiple cavities. The instrumented cavities included, four transducers mounted on the impeller shell, on the channel between blades. Six transducers mounted on the pressure and suction sides …
-
CHARACTERIZATION OF HYDRAULIC INTERACTIONS BETWEEN TORQUE CONVERTER AND TRANSMISSION DURING TRANSIENT EVENTS
A torque converter was instrumented with 29 pressure transducers to measure the torus, clutch plate, and torque converter cavities using telemetry to transfer the data. The torque converter was placed in a six-speed front wheel drive transmission and a test cell was built to drive and load the …
-
Characterization of Torque Converter Cavitation Sound Power Level over Varying Speed Ratio
… operating parameters of a matrix of automotive torque converters. Cavitation in a torque converter can reduce torque converter performance and produce noise levels significant enough to be audible in the vehicle cab. The trend toward smaller and more compact torque converters increases the risk …
-
Experimental measurements of the flow field inside of an automotive torque converter
Thesis (M.S.)--Michigan State University. Department of Mechanical Engineering, 1998
-
CORRELATED SIMULATION OF PSEUDO TRANSIENT TORQUE CONVERTER CLUTCH ENGAGEMENT USING COUPLED FLUID-STRUCTURE INTERACTION
… Interaction simulation of a two path torque converter to predict the flow field inside the torque converter and the torque capacity of the torque converter clutch during a pseudo transient maneuver of engagement of clutch from SR 0.81 to 0.99. The pressure data of the CFD simulation is …
-
A quantitative study of primary flow fields within an automotive torque converter using laster doppler velocimetry
Thesis (M.S.)--Michigan State University. Department of Mechanical Engineering, 1998
-
DESIGN OF AN ANTI-JERK CONTROLLER FOR BOTH LOCKED AND SLIPPING TORQUE CONVERTER CONDITIONS IN A VEHICLE
… in the drivetrain when a sudden demand for torque rise or drop is made. Another such parameter is the sluggishness in the delivery of torque at wheels against the requested torque by the driver. This can exist due to the shift in the dynamics during the drivetrain operation from locked …
-
EXPERIMENTAL EVALUATION AND SIMULATION OF TORQUE TRANSMISSIBILITY FREQUENCY RESPONSE FUNCTIONS OF VIBRATION ISOLATORS AND ABSORBERS FOR DRIVETRAIN APPLICATIONS
… Two studies feature experiments on several torque converters, clutch locked and open, to validate models of the hardware. The last study details experiments on a centrifugal pendulum absorber in a torque converter, to characterize the viscous friction while submerged in automatic …
-
Modeling, optimization, and motion control for off-road Vehicles
… wheel loaders occur mainly in the engine, torque converter, and hydraulic main pump. For diesel systems, the proposed optimization and control approach improves the operating conditions of each component, thereby reducing losses and improving efficiency. In contrast, the electrification …
-
Enhancing remanufacturing automation using deep learning approach
… further investigates the empirical data of torque converter components recorded from a remanufacturing facility in Glasgow, UK, using the in-case and cross-case analysis to evaluate the remanufacturing inspection, sorting, and process control applications. -- Nevertheless, the developed …
-
Dynamic Temperature Model of an Automatic Transmission
… losses were different on every gear. However the torque converter was open on the first gear, and could not be closed, which led to the decision to only test the remaining gears since the first gear will only be used during short times during most driving scenarios. To verify the model, simple …
-
Control Oriented Modeling of an Automotive Drivetrain for Anti-Jerk Control
… is developed, which includes the engine as a torque generator, backlash elements as discontinuities, and driveshafts as compliant elements. Experimental validation results showed that the accuracy of the developed model, in representing shuffle oscillation frequency, during the tip-in …
-
Automotive Driveline Backlash State and Size Estimator Design for Anti-Jerk Control
… in the previous works, is validated for a locked torque converter case along with its reduced order model which is used for estimator development. The error in the simulated shuffle frequency for the full order model and reduced order model is less than 1%. The reduced order model is then used to …
-
Acausal Powertrain Modelling with Application to Model-based Powertrain Control
… spark ignition engine, and a hydrodynamic torque converter model. Then, the models are integrated along with the rest of a powertrain's components (e.g. vehicle longitudinal dynamics model) through acausal connections, which represents a more feasible physics-based powertrain model for …
Page 1 of 2