Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 158 for “"Tube wall"”.
-
Experimental Investigation of Heated-Tube Wall Ignition in a Han-Based Green Monopropellant
… tubing with an outer diameter of 0.25 inches, wall thickness of 0.0245 inches and a length of 3 feet. This experimental section was instrumented with pressure transducers and thermocouples to detect and characterize the thermal ignition conditions of the HAN-based propellant. Utilizing the same …
-
The effect of circumferential tube wall heat conduction upon laminar filmwise condensation on the outside of condenser tubes.
… the thermal behavior of an internally-cooled tube in a condensing vapor. The analysis constitutes a unique application of the finite element method and provides new insights into the effects of circumferential conduction upon condenser tube performance. Comparisons are made between the present …
-
Effects of Louver Length and Vortex Generators to Augment Tube Wall Heat Transfer in Louvered Fin Heat Exchangers
… the effect of louver length on pressure drop and tube wall heat transfer, which is the primary heat transfer surface in the heat exchanger. The second is to augment tube wall heat transfer with the use of delta winglets placed on the fins near the tube wall. These studies were completed on a 20X …
-
Effects of rf power and tube wall temperature on plasma stability and analyte emission in furnace atomization plasma excitation spectrometry
… and does not depend absolutely on the furnace wall temperature but on the temperature of rf center electrode. The spatial distribution of analyte in the plasma shows an increase in emission intensity from the center of the furnace toward the wall, reaches a maximum at 1.25 mm from the center, …
-
Measurements and Predictions of the Heat Transfer at the Tube-Fin Junction for Louvered Fin Heat Exchangers
… govern air side heat transfer is required. The tube wall heat transfer results presented in this paper were obtained both experimentally and computationally for a typical compact heat exchanger design. Both isothermal and constant heat flux tube walls were studied. For the experimental …
-
Practical Applications of Delta Winglets in Compact Heat Exchangers with Louvered Fins
… vehicle designs. Air-side resistance on the tube wall and louvered fin surfaces comprises over 85% of total resistance to heat transfer in louvered fin heat exchangers. The tube wall surface is considered the primary surface for heat transfer, where the temperature between the working fluid …
-
Modelling the Impact of Tube Fouling on Heat Transfer in Once-Through Steam Generators
… transfer efficiency in OTSGs and can increase tube wall temperatures above safe operating limits, potentially causing tube failures. For conductivities between 0.05 – 2 W/m K and thicknesses between 0.1 – 30% of inner radius (0.4 – 11 mm), average tube wall temperatures above safe literature …
-
Mathematical Modelling of an Industrial Steam Methane Reformer
… simulations and on-line monitoring of tube-wall temperatures. The model calculates temperature profiles for the outer-tube wall, inner-tube wall, furnace gas and process gas. Reformer performance ratios and composition profiles are also computed. The model inputs are the reformer …
-
Investigation of hybridoma cell death by recirculation
… were studied. Flow conditions corresponding to tube wall shear stresses ofup to 1.29 dyn/cm² proved to be harmless to cells in recirculation; stresses of 1.73-2.59 dyn/cm² caused a very slow but unrecoverable cell death; stresses of 3.45 dyn/cm² disrupted the cells and hampered metabolism …
-
Protective, Delayed, and Propagated Oxidation Regimes in Fe9Cr1Mo Steel Heat Exchanger Tubes in Simulated AGR Conditions
… behaviour of experimental Fe9Cr1Mo steel finned tubes under high-temperature CO2 environments for simulated advanced gas-cooled reactor (AGR) operating conditions. Through a combination of correlative microscopy, long-term exposure analysis, and advanced imaging methods, five distinct oxidation …
-
Stitch weld effect on solar collector efficiency factor
… from the plate to the fluid flowing inside the tube has been presented. The heat transfer coefficient based on the difference between bond temperature and fluid bulk mean temperature is an important factor in determining the collector efficiency factor F'. The upper and lower limits of the …
-
Strain-induced self-rolled-up semiconductor micro/nanotubes: Fabrication and characterization
Strain-induced self-rolled-up semiconductor nanotubes are a new type of building block for three-dimensional architectures. Semiconductor nanotubes (SNTs) take advantage of the lattice mismatch between different layers and are formed when the strained semiconductor layers are released from the …
-
Investigation of heat transfer in a vertical annulus
… The heat exchanger used consisted of a straight tube in tube test section with water as the heat transfer medium in both tubes „ Convection coefficients of heat transfer between the inner tube and the fluid flowing in the annulus were determined from the measured inner tube wall and average fluid …
-
Development, performance measurement, and modelling of a packed-bed, fire-tube heater
Fire-tubes are good candidates for indirect heating of pyrolysis and gasification reactors because of their simplicity and low cost. Typical fire-tube designs use empty tubes filled with hot combustion gases. The open-tube design suffers from a low overall thermal efficiency, typically on the order …
-
Primary Development of a Propane Air Combustor
… of measurements of flame temperature, flame tube wall temperature, and flame tube exit plane temperature. A comparison was made between the experimental and theoretical flame temperatures. The uniformity of air flow in the annulus between the flame tube and outer casing was investigated. …
-
Heat transfer to Boiling Liquids
… thermocouple and the temperature of the tube wall, very near the film, at various levels are measured by fixed thermocouples. The installation of these thermocouples in the tube wall is a skilful and at the same time troublesome job. This laborious method has been avoided by finding out …
-
Analysis of Flow and Heat Transfer in OTSGs and Injection Wells
… the thicker the foulant, the higher the outer tube wall temperature and the lower is the water temperature – the foulant acts as an insulator on the inner wall of the tube. Flow perturbations are demonstrated to yield benefits for lowering the outer tube wall temperature. An examination of …
-
A study of thermal transients involving hydrodynamic variation in the thermal entrance region of a circular tube
… transient associated with step increases in wall temperature for laminar gas flow in a clrcular tube is presented. The basic governing equations are derived with property variations taken into account. The governing equations are put into an appropriate form for numerical solution. Problem …
Page 1 of 8